According to user manual / programming guide there is no separate PCIe
phy 3A and 3B, but one 8-lane QMP PCIe Gen5 PHY which consists of two
4-lane blocks.  This is also visible in memory map, where the 0xf00000
is marked as the main block with additional sub blocks for each 4-lane
phys.

Describing the sub phys without the rest is not correct from hardware
description, even if it works.

Link: https://lore.kernel.org/r/20260420-optimistic-unnatural-stingray-80da35@quoll/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>

---

Changes in v2:
1. Rebase (context)
---
 arch/arm64/boot/dts/qcom/glymur-crd.dtsi |  5 ---
 arch/arm64/boot/dts/qcom/glymur.dtsi     | 39 +-----------------------
 2 files changed, 1 insertion(+), 43 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/glymur-crd.dtsi b/arch/arm64/boot/dts/qcom/glymur-crd.dtsi
index e784b538f42e..6e2e06ae6c8a 100644
--- a/arch/arm64/boot/dts/qcom/glymur-crd.dtsi
+++ b/arch/arm64/boot/dts/qcom/glymur-crd.dtsi
@@ -451,11 +451,6 @@ &pcie3b {
 	pinctrl-names = "default";
 };
 
-&pcie3b_phy {
-	vdda-phy-supply = <&vreg_l3c_e1_0p89>;
-	vdda-pll-supply = <&vreg_l2c_e1_1p14>;
-};
-
 &pcie3b_port0 {
 	reset-gpios = <&tlmm 155 GPIO_ACTIVE_LOW>;
 	wake-gpios = <&tlmm 157 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/qcom/glymur.dtsi b/arch/arm64/boot/dts/qcom/glymur.dtsi
index 20b49af7298e..0ecf1fcd700e 100644
--- a/arch/arm64/boot/dts/qcom/glymur.dtsi
+++ b/arch/arm64/boot/dts/qcom/glymur.dtsi
@@ -770,7 +770,7 @@ gcc: clock-controller@100000 {
 				 <0>,				/* USB 2 Phy PIPEGMUX */
 				 <0>,				/* USB 2 Phy SYS PCIE PIPEGMUX */
 				 <0>,				/* PCIe 3a */
-				 <&pcie3b_phy>,			/* PCIe 3b */
+				 <0>,				/* PCIe 3b */
 				 <&pcie4_phy>,			/* PCIe 4 */
 				 <&pcie5_phy>,			/* PCIe 5 */
 				 <&pcie6_phy>,			/* PCIe 6 */
@@ -3659,49 +3659,12 @@ pcie3b_port0: pcie@0 {
 				reg = <0x0 0x0 0x0 0x0 0x0>;
 				bus-range = <0x01 0xff>;
 
-				phys = <&pcie3b_phy>;
-
 				#address-cells = <3>;
 				#size-cells = <2>;
 				ranges;
 			};
 		};
 
-		pcie3b_phy: phy@f10000 {
-			compatible = "qcom,glymur-qmp-gen5x4-pcie-phy";
-			reg = <0x0 0x00f10000 0x0 0x10000>;
-
-			clocks = <&gcc GCC_PCIE_PHY_3B_AUX_CLK>,
-				 <&gcc GCC_PCIE_3B_CFG_AHB_CLK>,
-				 <&tcsr TCSR_PCIE_3_CLKREF_EN>,
-				 <&gcc GCC_PCIE_3B_PHY_RCHNG_CLK>,
-				 <&gcc GCC_PCIE_3B_PIPE_CLK>,
-				 <&gcc GCC_PCIE_3B_PIPE_DIV2_CLK>;
-			clock-names = "aux",
-				      "cfg_ahb",
-				      "ref",
-				      "rchng",
-				      "pipe",
-				      "pipediv2";
-
-			resets = <&gcc GCC_PCIE_3B_PHY_BCR>,
-				 <&gcc GCC_PCIE_3B_NOCSR_COM_PHY_BCR>;
-			reset-names = "phy",
-				      "phy_nocsr";
-
-			assigned-clocks = <&gcc GCC_PCIE_3B_PHY_RCHNG_CLK>;
-			assigned-clock-rates = <100000000>;
-
-			power-domains = <&gcc GCC_PCIE_3B_PHY_GDSC>;
-
-			#clock-cells = <0>;
-			clock-output-names = "pcie3b_pipe_clk";
-
-			#phy-cells = <0>;
-
-			status = "disabled";
-		};
-
 		cryptobam: dma-controller@1dc4000 {
 			compatible = "qcom,bam-v1.7.4", "qcom,bam-v1.7.0";
 			reg = <0x0 0x01dc4000 0x0 0x28000>;
-- 
2.53.0