Change TEGRA_USB_HOSTPC1_DEVLC_PTS_HSIC to its literal value instead of
using the BIT macro, as it is an enumeration. Correct the spelling in the
comment and rename uhsic_registers_shift to uhsic_registers_offset.
These changes are cosmetic and do not affect code behavior.

Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
---
 drivers/usb/phy/phy-tegra-usb.c   | 12 ++++++------
 include/linux/usb/tegra_usb_phy.h |  4 ++--
 2 files changed, 8 insertions(+), 8 deletions(-)

diff --git a/drivers/usb/phy/phy-tegra-usb.c b/drivers/usb/phy/phy-tegra-usb.c
index effa767ec019..3a7a74f01d1c 100644
--- a/drivers/usb/phy/phy-tegra-usb.c
+++ b/drivers/usb/phy/phy-tegra-usb.c
@@ -48,7 +48,7 @@
 #define TEGRA_USB_HOSTPC1_DEVLC			0x1b4
 #define   TEGRA_USB_HOSTPC1_DEVLC_PTS(x)	(((x) & 0x7) << 29)
 #define   TEGRA_USB_HOSTPC1_DEVLC_PHCD		BIT(22)
-#define   TEGRA_USB_HOSTPC1_DEVLC_PTS_HSIC	BIT(2)
+#define   TEGRA_USB_HOSTPC1_DEVLC_PTS_HSIC	4
 
 /* Bits of PORTSC1, which will get cleared by writing 1 into them */
 #define TEGRA_PORTSC1_RWC_BITS	(PORT_CSC | PORT_PEC | PORT_OCC)
@@ -169,7 +169,7 @@
 /*
  * Tegra20 has no UTMIP registers on PHY2 and UHSIC registers start from 0x800
  * just where UTMIP registers should have been. This is the case only with Tegra20
- * Tegra30+ have UTMIP registers at 0x800 and UHSIC registers shifter by 0x400
+ * Tegra30+ have UTMIP registers at 0x800 and UHSIC registers are shifted by 0x400
  * to 0xc00, but register layout is preserved.
  */
 #define UHSIC_PLL_CFG1				0x804
@@ -873,7 +873,7 @@ static int ulpi_phy_power_off(struct tegra_usb_phy *phy)
 static u32 tegra_hsic_readl(struct tegra_usb_phy *phy, u32 reg)
 {
 	void __iomem *base = phy->regs;
-	u32 shift = phy->soc_config->uhsic_registers_shift;
+	u32 shift = phy->soc_config->uhsic_registers_offset;
 
 	return readl_relaxed(base + shift + reg);
 }
@@ -881,7 +881,7 @@ static u32 tegra_hsic_readl(struct tegra_usb_phy *phy, u32 reg)
 static void tegra_hsic_writel(struct tegra_usb_phy *phy, u32 reg, u32 value)
 {
 	void __iomem *base = phy->regs;
-	u32 shift = phy->soc_config->uhsic_registers_shift;
+	u32 shift = phy->soc_config->uhsic_registers_offset;
 
 	writel_relaxed(value, base + shift + reg);
 }
@@ -1469,7 +1469,7 @@ static const struct tegra_phy_soc_config tegra20_soc_config = {
 	.requires_usbmode_setup = false,
 	.requires_extra_tuning_parameters = false,
 	.requires_pmc_ao_power_up = false,
-	.uhsic_registers_shift = 0,
+	.uhsic_registers_offset = 0,
 	.uhsic_tx_rtune = 0, /* 40 ohm */
 };
 
@@ -1479,7 +1479,7 @@ static const struct tegra_phy_soc_config tegra30_soc_config = {
 	.requires_usbmode_setup = true,
 	.requires_extra_tuning_parameters = true,
 	.requires_pmc_ao_power_up = true,
-	.uhsic_registers_shift = 0x400,
+	.uhsic_registers_offset = 0x400,
 	.uhsic_tx_rtune = 8,  /* 50 ohm */
 };
 
diff --git a/include/linux/usb/tegra_usb_phy.h b/include/linux/usb/tegra_usb_phy.h
index 1a8843bd1e95..fbdd2dcb3a2b 100644
--- a/include/linux/usb/tegra_usb_phy.h
+++ b/include/linux/usb/tegra_usb_phy.h
@@ -24,7 +24,7 @@ struct gpio_desc;
  * requires_extra_tuning_parameters: true if xcvr_hsslew, hssquelch_level
  *      and hsdiscon_level should be set for adequate signal quality
  * requires_pmc_ao_power_up: true if USB AO is powered down by default
- * uhsic_registers_shift: for Tegra30+ where HSIC registers were shifted
+ * uhsic_registers_offset: for Tegra30+ where HSIC registers were offset
  *      comparing to Tegra20 by 0x400, since Tegra20 has no UTMIP on PHY2
  * uhsic_tx_rtune: fine tuned 50 Ohm termination resistor for NMOS/PMOS driver
  */
@@ -35,7 +35,7 @@ struct tegra_phy_soc_config {
 	bool requires_usbmode_setup;
 	bool requires_extra_tuning_parameters;
 	bool requires_pmc_ao_power_up;
-	u32 uhsic_registers_shift;
+	u32 uhsic_registers_offset;
 	u32 uhsic_tx_rtune;
 };
 
-- 
2.51.0