From: Herve Codina <herve.codina@bootlin.com>

In RZ/N1 SoCs, CPUs are allowed to work at 125, 250 or 500 MHz when the
'ref' clock frequency value is set to 500 MHz which is the default 'ref'
clock frequency value.

Add support for CPU frequency scaling defining those 3 frequencies in
the opp-table with the assumption that the 'ref' clock is set to its
default value.

Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
---
 arch/arm/boot/dts/renesas/r9a06g032.dtsi | 35 ++++++++++++++++++++++++
 1 file changed, 35 insertions(+)

diff --git a/arch/arm/boot/dts/renesas/r9a06g032.dtsi b/arch/arm/boot/dts/renesas/r9a06g032.dtsi
index 8debb77803bb..9f21d8fba940 100644
--- a/arch/arm/boot/dts/renesas/r9a06g032.dtsi
+++ b/arch/arm/boot/dts/renesas/r9a06g032.dtsi
@@ -15,6 +15,39 @@ / {
 	#size-cells = <1>;
 	interrupt-parent = <&gic>;
 
+	/*
+	 * The CPUs clock is based on the 'ref' clock (output of OPPDIV divisor)
+	 * with x1, x2 or x4 ratio between the CPUs clock frequency and this
+	 * 'ref' clock frequency.
+	 *
+	 * The table below is built on the assumption that the 'ref' clock
+	 * frequency is set to 500MHz which is its default value.
+	 *
+	 * The table should be overridden in the board device-tree file based
+	 * on the 'ref' clock frequency if this frequency value is not the
+	 * default one.
+	 */
+	cpu_opp_table: opp-table-cpu {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-125000000 {
+			opp-hz = /bits/ 64 <125000000>;
+			/* ~35 clocks cycles at 125mhz */
+			clock-latency-ns = <300>;
+		};
+
+		opp-250000000 {
+			opp-hz = /bits/ 64 <250000000>;
+			clock-latency-ns = <300>;
+		};
+
+		opp-500000000 {
+			opp-hz = /bits/ 64 <500000000>;
+			clock-latency-ns = <300>;
+		};
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -24,6 +57,7 @@ cpu@0 {
 			compatible = "arm,cortex-a7";
 			reg = <0>;
 			clocks = <&sysctrl R9A06G032_CLK_A7MP>;
+			operating-points-v2 = <&cpu_opp_table>;
 		};
 
 		cpu@1 {
@@ -33,6 +67,7 @@ cpu@1 {
 			clocks = <&sysctrl R9A06G032_CLK_A7MP>;
 			enable-method = "renesas,r9a06g032-smp";
 			cpu-release-addr = <0 0x4000c204>;
+			operating-points-v2 = <&cpu_opp_table>;
 		};
 	};
 
-- 
2.52.0

Hi all,

SOB lines and author are not correct.

Even if it's me (Herve Codina) in all cases, I messed me up with the
"(Schneider Electric)" part.

Please ignore this v1. I will send a v2 with correct SoB and author.

Sorry for the noise.

Best regards,
Hervé


On Thu, 15 Jan 2026 17:01:44 +0100
"Herve Codina (Schneider Electric)" <herve.codina@bootlin.com> wrote:

> From: Herve Codina <herve.codina@bootlin.com>
> 
...
> 
> Signed-off-by: Herve Codina <herve.codina@bootlin.com>
> Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>