From: Sushrut Shree Trivedi <quic_sushruts@quicinc.com>

PCIe0 is routed to an m.2 E key connector on the mainboard for wifi
attaches while PCIe1 routes to a standard PCIe x4 expansion slot.
Hence, enable the PCIe0 and PCIe1 controller and phy-nodes.

Signed-off-by: Sushrut Shree Trivedi <quic_sushruts@quicinc.com>
Signed-off-by: Ziyue Zhang <ziyue.zhang@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/monaco-evk.dts | 85 +++++++++++++++++++++++++
 1 file changed, 85 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/monaco-evk.dts b/arch/arm64/boot/dts/qcom/monaco-evk.dts
index bb35893da73d..5b9966bd6c3c 100644
--- a/arch/arm64/boot/dts/qcom/monaco-evk.dts
+++ b/arch/arm64/boot/dts/qcom/monaco-evk.dts
@@ -400,6 +400,44 @@ &iris {
 	status = "okay";
 };
 
+&pcie0 {
+	pinctrl-0 = <&pcie0_default_state>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie0_phy {
+	vdda-phy-supply = <&vreg_l6a>;
+	vdda-pll-supply = <&vreg_l5a>;
+
+	status = "okay";
+};
+
+&pcie1 {
+	pinctrl-0 = <&pcie1_default_state>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie1_phy {
+	vdda-phy-supply = <&vreg_l6a>;
+	vdda-pll-supply = <&vreg_l5a>;
+
+	status = "okay";
+};
+
+&pcieport0 {
+	reset-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+};
+
+&pcieport1 {
+	reset-gpios = <&tlmm 23 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+};
+
 &qupv3_id_0 {
 	firmware-name = "qcom/qcs8300/qupv3fw.elf";
 	status = "okay";
@@ -435,6 +473,30 @@ &serdes0 {
 };
 
 &tlmm {
+
+	pcie0_default_state: pcie0-default-state {
+		wake-pins {
+			pins = "gpio0";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		clkreq-pins {
+			pins = "gpio1";
+			function = "pcie0_clkreq";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-pins {
+			pins = "gpio2";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
 	ethernet0_default: ethernet0-default-state {
 		ethernet0_mdc: ethernet0-mdc-pins {
 			pins = "gpio5";
@@ -458,6 +520,29 @@ qup_i2c1_default: qup-i2c1-state {
 		bias-pull-up;
 	};
 
+	pcie1_default_state: pcie1-default-state {
+		wake-pins {
+			pins = "gpio21";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		clkreq-pins {
+			pins = "gpio22";
+			function = "pcie1_clkreq";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-pins {
+			pins = "gpio23";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
 	qup_i2c15_default: qup-i2c15-state {
 		pins = "gpio91", "gpio92";
 		function = "qup1_se7";
-- 
2.34.1