Monaco EVK is a single-board computer based on the Qualcomm QCS8300 SoC.
It lacks a camera sensor in its default configuration.
This series adds CCI support and enables the IMX577 sensor via CSIPHY1
through device tree overlay.
We have tested IMX577 Sensor on CCI1 with following commands:
- media-ctl --reset
- media-ctl -V '"imx577 3-001a":0[fmt:SRGGB10/4056x3040 field:none]'
- media-ctl -V '"msm_csiphy1":0[fmt:SRGGB10/4056x3040]'
- media-ctl -V '"msm_csid0":0[fmt:SRGGB10/4056x3040]'
- media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB10/4056x3040]'
- media-ctl -l '"msm_csiphy1":1->"msm_csid0":0[1]'
- media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
- yavta -B capture-mplane -c -I -n 5 -f SRGGB10P -s 4056x3040 -F /dev/video1
---
This patch series depends on patch series:
https://lore.kernel.org/all/20250813053724.232494-1-quic_vikramsa@quicinc.com
Bindings for Supplies are added by below patch, Bryan is going to merge
this in linux-next:
https://lore.kernel.org/all/20250910104915.1444669-1-quic_vikramsa@quicinc.com/
Changes in V3:
- Updated and Wrapped commit messages for [PATCH v2 1/3] and [PATCH v2 2/3] - Rob
- Link to v2:
https://lore.kernel.org/all/20250912141134.2799078-1-quic_vikramsa@quicinc.com
Changes in V2:
- Remove the patch that adds PHY supply documentation in the qcs8300 CAMSS.
bindings. This change should be submitted together with the qcs8300 bindings patch.
- Fix indentation and regulator node name - Krzysztof.
- Update commit message as suggested - Dmitry.
- Link to v1:
https://lore.kernel.org/lkml/20250909114241.840842-1-quic_vikramsa@quicinc.com
Used following tools for the sanity check of these changes.
- make -j32 W=1
- checkpatch.pl
- make DT_CHECKER_FLAGS=-m W=1 DT_SCHEMA_FILES=i2c/qcom,i2c-cci.yaml dt_binding_check
- make CHECK_DTBS=y W=1 DT_SCHEMA_FILES=i2c/qcom,i2c-cci.yaml
Below 2 checks are passing by taking bindings from:
https://lore.kernel.org/all/20250910104915.1444669-1-quic_vikramsa@quicinc.com/
- make DT_CHECKER_FLAGS=-m W=1 DT_SCHEMA_FILES=media/qcom,qcs8300-camss.yaml dt_binding_check
- make CHECK_DTBS=y W=1 DT_SCHEMA_FILES=media/qcom,qcs8300-camss.yaml
Signed-off-by: Nihal Kumar Gupta <quic_nihalkum@quicinc.com>
Signed-off-by: Vikram Sharma <quic_vikramsa@quicinc.com>
Nihal Kumar Gupta (3):
dt-bindings: i2c: qcom-cci: Document qcs8300 compatible
arm64: dts: qcom: qcs8300: Add CCI definitions
arm64: dts: qcom: monaco-evk-camera: Add DT overlay
.../devicetree/bindings/i2c/qcom,i2c-cci.yaml | 2 +
arch/arm64/boot/dts/qcom/Makefile | 4 +
.../dts/qcom/monaco-evk-camera-imx577.dtso | 96 ++++++
arch/arm64/boot/dts/qcom/qcs8300.dtsi | 309 ++++++++++++++++++
4 files changed, 411 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/monaco-evk-camera-imx577.dtso
--
2.25.1