1. Patchew
  2. linux
  3. [PATCH v2 0/7] Add DSI display support for TI's Jacinto platforms
  4. View patch

[PATCH v2 6/7] arm64: dts: ti: k3-j721s2-common-proc-board: Enable DisplayPort-1

Jayesh Choudhary posted 7 patches 7 months, 2 weeks ago
There is a newer version of this series
[PATCH v2 6/7] arm64: dts: ti: k3-j721s2-common-proc-board: Enable DisplayPort-1
Posted by Jayesh Choudhary 7 months, 2 weeks ago 
Enable DSI display for J721S2 EVM.

Add the endpoint nodes to describe connection from:
DSS => DSI Bridge => DSI to eDP bridge => DisplayPort-1

Set status for all required nodes for DisplayPort-1 as 'okay'.

Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
---
 .../dts/ti/k3-j721s2-common-proc-board.dts    | 89 +++++++++++++++++++
 1 file changed, 89 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index 793d50344fad..efe857a50bb1 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -93,6 +93,29 @@ vdd_sd_dv: gpio-regulator-TLV71033 {
 			 <3300000 0x1>;
 	};
 
+	dp1_pwr_3v3: regulator-dp1-prw {
+		compatible = "regulator-fixed";
+		regulator-name = "dp1-pwr";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&exp4 1 GPIO_ACTIVE_HIGH>; /* P1 - DP1_PWR_SW_EN */
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	dp1: connector-dp1 {
+		compatible = "dp-connector";
+		label = "DP1";
+		type = "full-size";
+		dp-pwr-supply = <&dp1_pwr_3v3>;
+
+		port {
+			dp1_connector_in: endpoint {
+				remote-endpoint = <&dp1_out>;
+			};
+		};
+	};
+
 	transceiver1: can-phy1 {
 		compatible = "ti,tcan1043";
 		#phy-cells = <0>;
@@ -563,3 +586,69 @@ &main_mcan5 {
 	pinctrl-0 = <&main_mcan5_pins_default>;
 	phys = <&transceiver4>;
 };
+
+&dss {
+	/*
+	 * DSS on J721S2-EVM supports DP on VP0 and DSI on VP2.
+	 * These clock assignments are chosen to enable the following outputs:
+	 * VP0 - DisplayPort SST
+	 * VP2 - DSI
+	 */
+	status = "okay";
+	assigned-clocks = <&k3_clks 158 2>,
+			  <&k3_clks 158 14>;
+	assigned-clock-parents = <&k3_clks 158 3>,
+				 <&k3_clks 158 16>;
+};
+
+&dss_ports {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	port@2 {
+		reg = <2>;
+		dpi2_out: endpoint {
+			remote-endpoint = <&dsi0_in>;
+		};
+	};
+};
+
+&dsi0_ports {
+	port@0 {
+		reg = <0>;
+		dsi0_out: endpoint {
+			remote-endpoint = <&dp1_in>;
+		};
+	};
+
+	port@1 {
+		reg = <1>;
+		dsi0_in: endpoint {
+			remote-endpoint = <&dpi2_out>;
+		};
+	};
+};
+
+&dsi_edp_bridge_ports {
+	port@0 {
+		reg = <0>;
+		dp1_in: endpoint {
+			remote-endpoint = <&dsi0_out>;
+		};
+	};
+
+	port@1 {
+		reg = <1>;
+		dp1_out: endpoint {
+			remote-endpoint = <&dp1_connector_in>;
+		};
+	};
+};
+
+&dphy_tx0 {
+	status = "okay";
+};
+
+&dsi0 {
+	status = "okay";
+};
-- 
2.34.1
Re: [PATCH v2 6/7] arm64: dts: ti: k3-j721s2-common-proc-board: Enable DisplayPort-1
Posted by Kumar, Udit 7 months, 2 weeks ago 
On 6/24/2025 1:56 PM, Jayesh Choudhary wrote:
> Enable DSI display for J721S2 EVM.
>
> Add the endpoint nodes to describe connection from:
> DSS => DSI Bridge => DSI to eDP bridge => DisplayPort-1
>
> Set status for all required nodes for DisplayPort-1 as 'okay'.
>
> Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
> ---
>   .../dts/ti/k3-j721s2-common-proc-board.dts    | 89 +++++++++++++++++++
>   1 file changed, 89 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
> index 793d50344fad..efe857a50bb1 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
> @@ -93,6 +93,29 @@ vdd_sd_dv: gpio-regulator-TLV71033 {
>   			 <3300000 0x1>;
>   	};
>   
> +	dp1_pwr_3v3: regulator-dp1-prw {
> +		compatible = "regulator-fixed";
> +		regulator-name = "dp1-pwr";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&exp4 1 GPIO_ACTIVE_HIGH>; /* P1 - DP1_PWR_SW_EN */
> +		enable-active-high;
> +		regulator-always-on;

Please check once, if this regulator falls under regulator-always-on case,

I can imagine a case, where DP1 is not used and still regulator is kept on


> +	};
> +
> +	dp1: connector-dp1 {
> +		compatible = "dp-connector";
> +		label = "DP1";
> +		type = "full-size";
> +		dp-pwr-supply = <&dp1_pwr_3v3>;
> +
> +		port {
> +			dp1_connector_in: endpoint {
> +				remote-endpoint = <&dp1_out>;
> +			};
> +		};
> +	};
> +
>   	transceiver1: can-phy1 {
>   		compatible = "ti,tcan1043";
>   		#phy-cells = <0>;
> @@ -563,3 +586,69 @@ &main_mcan5 {
>   	pinctrl-0 = <&main_mcan5_pins_default>;
>   	phys = <&transceiver4>;
>   };
> +
> +&dss {
> +	/*
> +	 * DSS on J721S2-EVM supports DP on VP0 and DSI on VP2.
> +	 * These clock assignments are chosen to enable the following outputs:
> +	 * VP0 - DisplayPort SST
> +	 * VP2 - DSI
> +	 */
> +	status = "okay";
> +	assigned-clocks = <&k3_clks 158 2>,
> +			  <&k3_clks 158 14>;
> +	assigned-clock-parents = <&k3_clks 158 3>,
> +				 <&k3_clks 158 16>;
> +};
> +
> +&dss_ports {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	port@2 {
> +		reg = <2>;
> +		dpi2_out: endpoint {
> +			remote-endpoint = <&dsi0_in>;
> +		};
> +	};
> +};
> +
> +&dsi0_ports {
> +	port@0 {
> +		reg = <0>;
> +		dsi0_out: endpoint {
> +			remote-endpoint = <&dp1_in>;
> +		};
> +	};
> +
> +	port@1 {
> +		reg = <1>;
> +		dsi0_in: endpoint {
> +			remote-endpoint = <&dpi2_out>;
> +		};
> +	};
> +};
> +
> +&dsi_edp_bridge_ports {
> +	port@0 {
> +		reg = <0>;
> +		dp1_in: endpoint {
> +			remote-endpoint = <&dsi0_out>;
> +		};
> +	};
> +
> +	port@1 {
> +		reg = <1>;
> +		dp1_out: endpoint {
> +			remote-endpoint = <&dp1_connector_in>;
> +		};
> +	};
> +};
> +
> +&dphy_tx0 {
> +	status = "okay";
> +};
> +
> +&dsi0 {
> +	status = "okay";
> +};
Re: [PATCH v2 6/7] arm64: dts: ti: k3-j721s2-common-proc-board: Enable DisplayPort-1
Posted by Jayesh Choudhary 6 months, 4 weeks ago 
Hello Udit,

On 26/06/25 16:04, Kumar, Udit wrote:
> 
> On 6/24/2025 1:56 PM, Jayesh Choudhary wrote:
>> Enable DSI display for J721S2 EVM.
>>
>> Add the endpoint nodes to describe connection from:
>> DSS => DSI Bridge => DSI to eDP bridge => DisplayPort-1
>>
>> Set status for all required nodes for DisplayPort-1 as 'okay'.
>>
>> Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
>> ---
>>   .../dts/ti/k3-j721s2-common-proc-board.dts    | 89 +++++++++++++++++++
>>   1 file changed, 89 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts 
>> b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
>> index 793d50344fad..efe857a50bb1 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
>> +++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
>> @@ -93,6 +93,29 @@ vdd_sd_dv: gpio-regulator-TLV71033 {
>>                <3300000 0x1>;
>>       };
>> +    dp1_pwr_3v3: regulator-dp1-prw {
>> +        compatible = "regulator-fixed";
>> +        regulator-name = "dp1-pwr";
>> +        regulator-min-microvolt = <3300000>;
>> +        regulator-max-microvolt = <3300000>;
>> +        gpio = <&exp4 1 GPIO_ACTIVE_HIGH>; /* P1 - DP1_PWR_SW_EN */
>> +        enable-active-high;
>> +        regulator-always-on;
> 
> Please check once, if this regulator falls under regulator-always-on case,
> 
> I can imagine a case, where DP1 is not used and still regulator is kept on

Yes it is not required.
I will remove this property from j721s2-common-proc-board and am68-sk
board dts.

Thanks,
Jayesh

> 
> 
>> +    };
>> +
>> +    dp1: connector-dp1 {
>> +        compatible = "dp-connector";

[...]

Patchew 2.1-devel-b67e4c2

© 2016 - 2026 Red Hat, Inc.