There are many fuzzy register variables in the lpuart driver, such as
temp, tmp, val, reg. Let's give these register variables more specific
names.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
drivers/tty/serial/fsl_lpuart.c | 220 ++++++++++++++++----------------
1 file changed, 110 insertions(+), 110 deletions(-)
diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
index 3b48e320e7f4..c8cc0a241fba 100644
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -441,36 +441,36 @@ static unsigned int lpuart_get_baud_clk_rate(struct lpuart_port *sport)
static void lpuart_stop_tx(struct uart_port *port)
{
- u8 temp;
+ u8 cr2;
- temp = readb(port->membase + UARTCR2);
- temp &= ~(UARTCR2_TIE | UARTCR2_TCIE);
- writeb(temp, port->membase + UARTCR2);
+ cr2 = readb(port->membase + UARTCR2);
+ cr2 &= ~(UARTCR2_TIE | UARTCR2_TCIE);
+ writeb(cr2, port->membase + UARTCR2);
}
static void lpuart32_stop_tx(struct uart_port *port)
{
- u32 temp;
+ u32 ctrl;
- temp = lpuart32_read(port, UARTCTRL);
- temp &= ~(UARTCTRL_TIE | UARTCTRL_TCIE);
- lpuart32_write(port, temp, UARTCTRL);
+ ctrl = lpuart32_read(port, UARTCTRL);
+ ctrl &= ~(UARTCTRL_TIE | UARTCTRL_TCIE);
+ lpuart32_write(port, ctrl, UARTCTRL);
}
static void lpuart_stop_rx(struct uart_port *port)
{
- u8 temp;
+ u8 cr2;
- temp = readb(port->membase + UARTCR2);
- writeb(temp & ~UARTCR2_RE, port->membase + UARTCR2);
+ cr2 = readb(port->membase + UARTCR2);
+ writeb(cr2 & ~UARTCR2_RE, port->membase + UARTCR2);
}
static void lpuart32_stop_rx(struct uart_port *port)
{
- u32 temp;
+ u32 ctrl;
- temp = lpuart32_read(port, UARTCTRL);
- lpuart32_write(port, temp & ~UARTCTRL_RE, UARTCTRL);
+ ctrl = lpuart32_read(port, UARTCTRL);
+ lpuart32_write(port, ctrl & ~UARTCTRL_RE, UARTCTRL);
}
static void lpuart_dma_tx(struct lpuart_port *sport)
@@ -599,7 +599,7 @@ static void lpuart_flush_buffer(struct uart_port *port)
{
struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
struct dma_chan *chan = sport->dma_tx_chan;
- u32 val;
+ u32 fifo;
if (sport->lpuart_dma_tx_use) {
if (sport->dma_tx_in_progress) {
@@ -611,13 +611,13 @@ static void lpuart_flush_buffer(struct uart_port *port)
}
if (lpuart_is_32(sport)) {
- val = lpuart32_read(port, UARTFIFO);
- val |= UARTFIFO_TXFLUSH | UARTFIFO_RXFLUSH;
- lpuart32_write(port, val, UARTFIFO);
+ fifo = lpuart32_read(port, UARTFIFO);
+ fifo |= UARTFIFO_TXFLUSH | UARTFIFO_RXFLUSH;
+ lpuart32_write(port, fifo, UARTFIFO);
} else {
- val = readb(port->membase + UARTCFIFO);
- val |= UARTCFIFO_TXFLUSH | UARTCFIFO_RXFLUSH;
- writeb(val, port->membase + UARTCFIFO);
+ fifo = readb(port->membase + UARTCFIFO);
+ fifo |= UARTCFIFO_TXFLUSH | UARTCFIFO_RXFLUSH;
+ writeb(fifo, port->membase + UARTCFIFO);
}
}
@@ -642,7 +642,7 @@ static int lpuart_poll_init(struct uart_port *port)
struct lpuart_port *sport = container_of(port,
struct lpuart_port, port);
unsigned long flags;
- u8 temp;
+ u8 fifo;
port->fifosize = 0;
@@ -650,9 +650,9 @@ static int lpuart_poll_init(struct uart_port *port)
/* Disable Rx & Tx */
writeb(0, port->membase + UARTCR2);
- temp = readb(port->membase + UARTPFIFO);
+ fifo = readb(port->membase + UARTPFIFO);
/* Enable Rx and Tx FIFO */
- writeb(temp | UARTPFIFO_RXFE | UARTPFIFO_TXFE,
+ writeb(fifo | UARTPFIFO_RXFE | UARTPFIFO_TXFE,
port->membase + UARTPFIFO);
/* flush Tx and Rx FIFO */
@@ -694,7 +694,7 @@ static int lpuart32_poll_init(struct uart_port *port)
{
unsigned long flags;
struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
- u32 temp;
+ u32 fifo;
port->fifosize = 0;
@@ -703,10 +703,10 @@ static int lpuart32_poll_init(struct uart_port *port)
/* Disable Rx & Tx */
lpuart32_write(port, 0, UARTCTRL);
- temp = lpuart32_read(port, UARTFIFO);
+ fifo = lpuart32_read(port, UARTFIFO);
/* Enable Rx and Tx FIFO */
- lpuart32_write(port, temp | UARTFIFO_RXFE | UARTFIFO_TXFE, UARTFIFO);
+ lpuart32_write(port, fifo | UARTFIFO_RXFE | UARTFIFO_TXFE, UARTFIFO);
/* flush Tx and Rx FIFO */
lpuart32_write(port, UARTFIFO_TXFLUSH | UARTFIFO_RXFLUSH, UARTFIFO);
@@ -789,10 +789,10 @@ static void lpuart_start_tx(struct uart_port *port)
{
struct lpuart_port *sport = container_of(port,
struct lpuart_port, port);
- u8 temp;
+ u8 cr2;
- temp = readb(port->membase + UARTCR2);
- writeb(temp | UARTCR2_TIE, port->membase + UARTCR2);
+ cr2 = readb(port->membase + UARTCR2);
+ writeb(cr2 | UARTCR2_TIE, port->membase + UARTCR2);
if (sport->lpuart_dma_tx_use) {
if (!lpuart_stopped_or_empty(port))
@@ -806,14 +806,14 @@ static void lpuart_start_tx(struct uart_port *port)
static void lpuart32_start_tx(struct uart_port *port)
{
struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
- u32 temp;
+ u32 ctrl;
if (sport->lpuart_dma_tx_use) {
if (!lpuart_stopped_or_empty(port))
lpuart_dma_tx(sport);
} else {
- temp = lpuart32_read(port, UARTCTRL);
- lpuart32_write(port, temp | UARTCTRL_TIE, UARTCTRL);
+ ctrl = lpuart32_read(port, UARTCTRL);
+ lpuart32_write(port, ctrl | UARTCTRL_TIE, UARTCTRL);
if (lpuart32_read(port, UARTSTAT) & UARTSTAT_TDRE)
lpuart32_transmit_buffer(sport);
@@ -1411,9 +1411,9 @@ static inline int lpuart_start_rx_dma(struct lpuart_port *sport)
dma_async_issue_pending(chan);
if (lpuart_is_32(sport)) {
- u32 temp = lpuart32_read(&sport->port, UARTBAUD);
+ u32 baud = lpuart32_read(&sport->port, UARTBAUD);
- lpuart32_write(&sport->port, temp | UARTBAUD_RDMAE, UARTBAUD);
+ lpuart32_write(&sport->port, baud | UARTBAUD_RDMAE, UARTBAUD);
if (sport->dma_idle_int) {
u32 ctrl = lpuart32_read(&sport->port, UARTCTRL);
@@ -1520,10 +1520,10 @@ static int lpuart32_config_rs485(struct uart_port *port, struct ktermios *termio
static unsigned int lpuart_get_mctrl(struct uart_port *port)
{
unsigned int mctrl = 0;
- u8 reg;
+ u8 cr1;
- reg = readb(port->membase + UARTCR1);
- if (reg & UARTCR1_LOOPS)
+ cr1 = readb(port->membase + UARTCR1);
+ if (cr1 & UARTCR1_LOOPS)
mctrl |= TIOCM_LOOP;
return mctrl;
@@ -1532,10 +1532,10 @@ static unsigned int lpuart_get_mctrl(struct uart_port *port)
static unsigned int lpuart32_get_mctrl(struct uart_port *port)
{
unsigned int mctrl = TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
- u32 reg;
+ u32 ctrl;
- reg = lpuart32_read(port, UARTCTRL);
- if (reg & UARTCTRL_LOOPS)
+ ctrl = lpuart32_read(port, UARTCTRL);
+ if (ctrl & UARTCTRL_LOOPS)
mctrl |= TIOCM_LOOP;
return mctrl;
@@ -1543,49 +1543,49 @@ static unsigned int lpuart32_get_mctrl(struct uart_port *port)
static void lpuart_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
- u8 reg;
+ u8 cr1;
- reg = readb(port->membase + UARTCR1);
+ cr1 = readb(port->membase + UARTCR1);
/* for internal loopback we need LOOPS=1 and RSRC=0 */
- reg &= ~(UARTCR1_LOOPS | UARTCR1_RSRC);
+ cr1 &= ~(UARTCR1_LOOPS | UARTCR1_RSRC);
if (mctrl & TIOCM_LOOP)
- reg |= UARTCR1_LOOPS;
+ cr1 |= UARTCR1_LOOPS;
- writeb(reg, port->membase + UARTCR1);
+ writeb(cr1, port->membase + UARTCR1);
}
static void lpuart32_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
- u32 reg;
+ u32 ctrl;
- reg = lpuart32_read(port, UARTCTRL);
+ ctrl = lpuart32_read(port, UARTCTRL);
/* for internal loopback we need LOOPS=1 and RSRC=0 */
- reg &= ~(UARTCTRL_LOOPS | UARTCTRL_RSRC);
+ ctrl &= ~(UARTCTRL_LOOPS | UARTCTRL_RSRC);
if (mctrl & TIOCM_LOOP)
- reg |= UARTCTRL_LOOPS;
+ ctrl |= UARTCTRL_LOOPS;
- lpuart32_write(port, reg, UARTCTRL);
+ lpuart32_write(port, ctrl, UARTCTRL);
}
static void lpuart_break_ctl(struct uart_port *port, int break_state)
{
- u8 temp;
+ u8 cr2;
- temp = readb(port->membase + UARTCR2) & ~UARTCR2_SBK;
+ cr2 = readb(port->membase + UARTCR2) & ~UARTCR2_SBK;
if (break_state != 0)
- temp |= UARTCR2_SBK;
+ cr2 |= UARTCR2_SBK;
- writeb(temp, port->membase + UARTCR2);
+ writeb(cr2, port->membase + UARTCR2);
}
static void lpuart32_break_ctl(struct uart_port *port, int break_state)
{
- u32 temp;
+ u32 ctrl;
- temp = lpuart32_read(port, UARTCTRL);
+ ctrl = lpuart32_read(port, UARTCTRL);
/*
* LPUART IP now has two known bugs, one is CTS has higher priority than the
@@ -1602,22 +1602,22 @@ static void lpuart32_break_ctl(struct uart_port *port, int break_state)
* Disable the transmitter to prevent any data from being sent out
* during break, then invert the TX line to send break.
*/
- temp &= ~UARTCTRL_TE;
- lpuart32_write(port, temp, UARTCTRL);
- temp |= UARTCTRL_TXINV;
- lpuart32_write(port, temp, UARTCTRL);
+ ctrl &= ~UARTCTRL_TE;
+ lpuart32_write(port, ctrl, UARTCTRL);
+ ctrl |= UARTCTRL_TXINV;
+ lpuart32_write(port, ctrl, UARTCTRL);
} else {
/* Disable the TXINV to turn off break and re-enable transmitter. */
- temp &= ~UARTCTRL_TXINV;
- lpuart32_write(port, temp, UARTCTRL);
- temp |= UARTCTRL_TE;
- lpuart32_write(port, temp, UARTCTRL);
+ ctrl &= ~UARTCTRL_TXINV;
+ lpuart32_write(port, ctrl, UARTCTRL);
+ ctrl |= UARTCTRL_TE;
+ lpuart32_write(port, ctrl, UARTCTRL);
}
}
static void lpuart_setup_watermark(struct lpuart_port *sport)
{
- u8 val, cr2, cr2_saved;
+ u8 fifo, cr2, cr2_saved;
cr2 = readb(sport->port.membase + UARTCR2);
cr2_saved = cr2;
@@ -1625,8 +1625,8 @@ static void lpuart_setup_watermark(struct lpuart_port *sport)
UARTCR2_RIE | UARTCR2_RE);
writeb(cr2, sport->port.membase + UARTCR2);
- val = readb(sport->port.membase + UARTPFIFO);
- writeb(val | UARTPFIFO_TXFE | UARTPFIFO_RXFE,
+ fifo = readb(sport->port.membase + UARTPFIFO);
+ writeb(fifo | UARTPFIFO_TXFE | UARTPFIFO_RXFE,
sport->port.membase + UARTPFIFO);
/* flush Tx and Rx FIFO */
@@ -1696,14 +1696,14 @@ static void lpuart32_setup_watermark(struct lpuart_port *sport)
static void lpuart32_setup_watermark_enable(struct lpuart_port *sport)
{
- u32 temp;
+ u32 ctrl;
lpuart32_setup_watermark(sport);
- temp = lpuart32_read(&sport->port, UARTCTRL);
- temp |= UARTCTRL_RE | UARTCTRL_TE;
- temp |= FIELD_PREP(UARTCTRL_IDLECFG, 0x7);
- lpuart32_write(&sport->port, temp, UARTCTRL);
+ ctrl = lpuart32_read(&sport->port, UARTCTRL);
+ ctrl |= UARTCTRL_RE | UARTCTRL_TE;
+ ctrl |= FIELD_PREP(UARTCTRL_IDLECFG, 0x7);
+ lpuart32_write(&sport->port, ctrl, UARTCTRL);
}
static void rx_dma_timer_init(struct lpuart_port *sport)
@@ -1820,16 +1820,16 @@ static void lpuart_hw_setup(struct lpuart_port *sport)
static int lpuart_startup(struct uart_port *port)
{
struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
- u8 temp;
+ u8 fifo;
/* determine FIFO size and enable FIFO mode */
- temp = readb(port->membase + UARTPFIFO);
+ fifo = readb(port->membase + UARTPFIFO);
- sport->txfifo_size = UARTFIFO_DEPTH((temp >> UARTPFIFO_TXSIZE_OFF) &
+ sport->txfifo_size = UARTFIFO_DEPTH((fifo >> UARTPFIFO_TXSIZE_OFF) &
UARTPFIFO_FIFOSIZE_MASK);
port->fifosize = sport->txfifo_size;
- sport->rxfifo_size = UARTFIFO_DEPTH((temp >> UARTPFIFO_RXSIZE_OFF) &
+ sport->rxfifo_size = UARTFIFO_DEPTH((fifo >> UARTPFIFO_RXSIZE_OFF) &
UARTPFIFO_FIFOSIZE_MASK);
lpuart_request_dma(sport);
@@ -1840,24 +1840,24 @@ static int lpuart_startup(struct uart_port *port)
static void lpuart32_hw_disable(struct lpuart_port *sport)
{
- u32 temp;
+ u32 ctrl;
- temp = lpuart32_read(&sport->port, UARTCTRL);
- temp &= ~(UARTCTRL_RIE | UARTCTRL_ILIE | UARTCTRL_RE |
+ ctrl = lpuart32_read(&sport->port, UARTCTRL);
+ ctrl &= ~(UARTCTRL_RIE | UARTCTRL_ILIE | UARTCTRL_RE |
UARTCTRL_TIE | UARTCTRL_TE);
- lpuart32_write(&sport->port, temp, UARTCTRL);
+ lpuart32_write(&sport->port, ctrl, UARTCTRL);
}
static void lpuart32_configure(struct lpuart_port *sport)
{
- u32 temp;
+ u32 ctrl;
- temp = lpuart32_read(&sport->port, UARTCTRL);
+ ctrl = lpuart32_read(&sport->port, UARTCTRL);
if (!sport->lpuart_dma_rx_use)
- temp |= UARTCTRL_RIE | UARTCTRL_ILIE;
+ ctrl |= UARTCTRL_RIE | UARTCTRL_ILIE;
if (!sport->lpuart_dma_tx_use)
- temp |= UARTCTRL_TIE;
- lpuart32_write(&sport->port, temp, UARTCTRL);
+ ctrl |= UARTCTRL_TIE;
+ lpuart32_write(&sport->port, ctrl, UARTCTRL);
}
static void lpuart32_hw_setup(struct lpuart_port *sport)
@@ -1880,16 +1880,16 @@ static void lpuart32_hw_setup(struct lpuart_port *sport)
static int lpuart32_startup(struct uart_port *port)
{
struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
- u32 temp;
+ u32 fifo;
/* determine FIFO size */
- temp = lpuart32_read(port, UARTFIFO);
+ fifo = lpuart32_read(port, UARTFIFO);
- sport->txfifo_size = UARTFIFO_DEPTH((temp >> UARTFIFO_TXSIZE_OFF) &
+ sport->txfifo_size = UARTFIFO_DEPTH((fifo >> UARTFIFO_TXSIZE_OFF) &
UARTFIFO_FIFOSIZE_MASK);
port->fifosize = sport->txfifo_size;
- sport->rxfifo_size = UARTFIFO_DEPTH((temp >> UARTFIFO_RXSIZE_OFF) &
+ sport->rxfifo_size = UARTFIFO_DEPTH((fifo >> UARTFIFO_RXSIZE_OFF) &
UARTFIFO_FIFOSIZE_MASK);
/*
@@ -1934,16 +1934,16 @@ static void lpuart_dma_shutdown(struct lpuart_port *sport)
static void lpuart_shutdown(struct uart_port *port)
{
struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
- u8 temp;
+ u8 cr2;
unsigned long flags;
uart_port_lock_irqsave(port, &flags);
/* disable Rx/Tx and interrupts */
- temp = readb(port->membase + UARTCR2);
- temp &= ~(UARTCR2_TE | UARTCR2_RE |
+ cr2 = readb(port->membase + UARTCR2);
+ cr2 &= ~(UARTCR2_TE | UARTCR2_RE |
UARTCR2_TIE | UARTCR2_TCIE | UARTCR2_RIE);
- writeb(temp, port->membase + UARTCR2);
+ writeb(cr2, port->membase + UARTCR2);
uart_port_unlock_irqrestore(port, flags);
@@ -2141,7 +2141,7 @@ static void __lpuart32_serial_setbrg(struct uart_port *port,
unsigned int baudrate, bool use_rx_dma,
bool use_tx_dma)
{
- u32 sbr, osr, baud_diff, tmp_osr, tmp_sbr, tmp_diff, tmp;
+ u32 sbr, osr, baud_diff, tmp_osr, tmp_sbr, tmp_diff, baud;
u32 clk = port->uartclk;
/*
@@ -2170,9 +2170,9 @@ static void __lpuart32_serial_setbrg(struct uart_port *port,
tmp_diff = clk / (tmp_osr * tmp_sbr) - baudrate;
/* select best values between sbr and sbr+1 */
- tmp = clk / (tmp_osr * (tmp_sbr + 1));
- if (tmp_diff > (baudrate - tmp)) {
- tmp_diff = baudrate - tmp;
+ baud = clk / (tmp_osr * (tmp_sbr + 1));
+ if (tmp_diff > (baudrate - baud)) {
+ tmp_diff = baudrate - baud;
tmp_sbr++;
}
@@ -2194,23 +2194,23 @@ static void __lpuart32_serial_setbrg(struct uart_port *port,
dev_warn(port->dev,
"unacceptable baud rate difference of more than 3%%\n");
- tmp = lpuart32_read(port, UARTBAUD);
+ baud = lpuart32_read(port, UARTBAUD);
if ((osr > 3) && (osr < 8))
- tmp |= UARTBAUD_BOTHEDGE;
+ baud |= UARTBAUD_BOTHEDGE;
- tmp &= ~(UARTBAUD_OSR_MASK << UARTBAUD_OSR_SHIFT);
- tmp |= ((osr-1) & UARTBAUD_OSR_MASK) << UARTBAUD_OSR_SHIFT;
+ baud &= ~(UARTBAUD_OSR_MASK << UARTBAUD_OSR_SHIFT);
+ baud |= ((osr-1) & UARTBAUD_OSR_MASK) << UARTBAUD_OSR_SHIFT;
- tmp &= ~UARTBAUD_SBR_MASK;
- tmp |= sbr & UARTBAUD_SBR_MASK;
+ baud &= ~UARTBAUD_SBR_MASK;
+ baud |= sbr & UARTBAUD_SBR_MASK;
if (!use_rx_dma)
- tmp &= ~UARTBAUD_RDMAE;
+ baud &= ~UARTBAUD_RDMAE;
if (!use_tx_dma)
- tmp &= ~UARTBAUD_TDMAE;
+ baud &= ~UARTBAUD_TDMAE;
- lpuart32_write(port, tmp, UARTBAUD);
+ lpuart32_write(port, baud, UARTBAUD);
}
static void lpuart32_serial_setbrg(struct lpuart_port *sport,
@@ -3085,7 +3085,7 @@ static int lpuart_suspend_noirq(struct device *dev)
static int lpuart_resume_noirq(struct device *dev)
{
struct lpuart_port *sport = dev_get_drvdata(dev);
- u32 val;
+ u32 stat;
pinctrl_pm_select_default_state(dev);
@@ -3094,8 +3094,8 @@ static int lpuart_resume_noirq(struct device *dev)
/* clear the wakeup flags */
if (lpuart_is_32(sport)) {
- val = lpuart32_read(&sport->port, UARTSTAT);
- lpuart32_write(&sport->port, val, UARTSTAT);
+ stat = lpuart32_read(&sport->port, UARTSTAT);
+ lpuart32_write(&sport->port, stat, UARTSTAT);
}
}
--
2.34.1© 2016 - 2026 Red Hat, Inc.