[PATCH v4 00/10] Implement setup_interface() in the DaVinci NAND controller

Bastien Curutchet posted 10 patches 1 week ago
drivers/memory/ti-aemif.c           | 187 +++++++++++++++++-----------
drivers/mtd/nand/raw/Kconfig        |   4 +-
drivers/mtd/nand/raw/davinci_nand.c |  94 +++++++++++++-
include/linux/memory/ti-aemif.h     |  32 +++++
4 files changed, 237 insertions(+), 80 deletions(-)
create mode 100644 include/linux/memory/ti-aemif.h
[PATCH v4 00/10] Implement setup_interface() in the DaVinci NAND controller
Posted by Bastien Curutchet 1 week ago
Hi all,

This patch series aims to implement the setup_interface() operation in
the DaVinci NAND controller to enable the use of all ONFI modes and
improve the NAND access speed.

PATCH 6 depends on PATCH 1-2-3-4-5
PATCH 10 depends on PATCH 6-8-9

This NAND controller is present in the DaVinci (OMAP L138) and Keystone2
SoCs and functions as a 'child' of the AEMIF controller. So its timings
are set by the AEMIF controller itself from device-tree properties.
Implementing the setup_interface() callback implies being able to update
dynamically these timings, so the first three patches of the series modify
the AEMIF driver to provide its 'children' a way to modify their chip
select timing configuration.

The remaining patches implement the setup_interface() operation.
The computation of the register's contents is directly based on
§20.3.2.3 of the OMAP-L138 TRM [1]

This has been tested on two platforms based upon the DaVinci SoC. One is
interfaced with a Macronix MX30UF4G18AC NAND, the other with a Toshiba
NAND.

[1] : https://www.ti.com/lit/ug/spruh77c/spruh77c.pdf

Change log:
 * v4
   PATCH 1,2,3 [new]:
     - Create the struct aemif_cs_timings inside the already existing
       struct aemif_cs_data
 * v3
   PATCH 1 [new]:
     - Wrap the verification of CS timing configuration into a function
   PATCH 2:
     - Fix comments
   PATCH 3:
     - Replace the spin-lock with a mutex
   PATCH 7:
     - Add handling of the NAND_DATA_IFACE_CHECK_ONLY case
     - setup_interface() returns errno on failures

 * v2
   Cover letter :
     - Add dependency details
     - Remove the question about ti-aemif.h location
   PATCH 1 :
     - Fix aemif_cs_timings's description in the comments
   PATCH 2 :
     - Fix typo in the config_cs_lock's description in the comments
     - Move include/memory/ti-aemif.h to include/linux/memory/ti-aemif.h
   PATCH 3 [NEW] :
     - Fix dependency issue with aemif controller in Kconfig
   PATCH 5 :
     - Add details about the clock bindings in the commit log
     - Replace devm_clk_get() with devm_clk_get_enabled()
     - Use dev_err_probe() to return the devm_clk_get_enabled() error

[v1] : https://lore.kernel.org/all/20241030104717.88688-1-bastien.curutchet@bootlin.com/
[v2] : https://lore.kernel.org/all/20241106085507.76425-1-bastien.curutchet@bootlin.com/
[v3] : https://lore.kernel.org/all/20241113094938.44817-1-bastien.curutchet@bootlin.com/

Bastien Curutchet (10):
  memory: ti-aemif: Store timings parameter in number of cycles - 1
  memory: ti-aemif: Remove unnecessary local variables
  memory: ti-aemif: Wrap CS timings into a struct
  memory: ti-aemif: Create aemif_check_cs_timings()
  memory: ti-aemif: Create aemif_set_cs_timings()
  memory: ti-aemif: Export aemif_*_cs_timings()
  mtd: rawnand: davinci: Always depends on TI_AEMIF
  mtd: rawnand: davinci: Order headers alphabetically
  mtd: rawnand: davinci: Add clock resource
  mtd: rawnand: davinci: Implement setup_interface() operation

 drivers/memory/ti-aemif.c           | 187 +++++++++++++++++-----------
 drivers/mtd/nand/raw/Kconfig        |   4 +-
 drivers/mtd/nand/raw/davinci_nand.c |  94 +++++++++++++-
 include/linux/memory/ti-aemif.h     |  32 +++++
 4 files changed, 237 insertions(+), 80 deletions(-)
 create mode 100644 include/linux/memory/ti-aemif.h

-- 
2.47.0

Re: [PATCH v4 00/10] Implement setup_interface() in the DaVinci NAND controller
Posted by Krzysztof Kozlowski 1 day, 6 hours ago
On 15/11/2024 14:26, Bastien Curutchet wrote:
> Hi all,
> 
> This patch series aims to implement the setup_interface() operation in
> the DaVinci NAND controller to enable the use of all ONFI modes and
> improve the NAND access speed.
> 
> PATCH 6 depends on PATCH 1-2-3-4-5
> PATCH 10 depends on PATCH 6-8-9

That's a bit too many to go via separate tree, so I'll provide them via
stable tag to Miquel/MTD.

Best regards,
Krzysztof
Re: [PATCH v4 00/10] Implement setup_interface() in the DaVinci NAND controller
Posted by Miquel Raynal 1 day, 1 hour ago
Hello Krzysztof,

On 21/11/2024 at 11:23:51 +01, Krzysztof Kozlowski <krzk@kernel.org> wrote:

> On 15/11/2024 14:26, Bastien Curutchet wrote:
>> Hi all,
>> 
>> This patch series aims to implement the setup_interface() operation in
>> the DaVinci NAND controller to enable the use of all ONFI modes and
>> improve the NAND access speed.
>> 
>> PATCH 6 depends on PATCH 1-2-3-4-5
>> PATCH 10 depends on PATCH 6-8-9
>
> That's a bit too many to go via separate tree, so I'll provide them via
> stable tag to Miquel/MTD.

Yep, works perfectly for me.

Cheers,
Miquèl