Move the common MMC "slot" properties because they are shared by the
single-slot or multi-slot controllers, and will help defining a simple
mmc-slot bindings document with proper slot properties and nodename.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 .../bindings/mmc/mmc-controller-common.yaml        | 357 +++++++++++++++++++++
 .../devicetree/bindings/mmc/mmc-controller.yaml    | 344 +-------------------
 2 files changed, 360 insertions(+), 341 deletions(-)

diff --git a/Documentation/devicetree/bindings/mmc/mmc-controller-common.yaml b/Documentation/devicetree/bindings/mmc/mmc-controller-common.yaml
new file mode 100644
index 000000000000..e02d3cbcc271
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/mmc-controller-common.yaml
@@ -0,0 +1,357 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mmc/mmc-controller-common.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MMC Controller & Slots Common Properties
+
+maintainers:
+  - Ulf Hansson <ulf.hansson@linaro.org>
+
+description: |
+  These properties are common to multiple MMC host controllers and the
+  possible slots or ports for multi-slot controllers.
+
+properties:
+  "#address-cells":
+    const: 1
+    description: |
+      The cell is the slot ID if a function subnode is used.
+
+  "#size-cells":
+    const: 0
+
+  # Card Detection.
+  # If none of these properties are supplied, the host native card
+  # detect will be used. Only one of them should be provided.
+
+  broken-cd:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      There is no card detection available; polling must be used.
+
+  cd-gpios:
+    maxItems: 1
+    description:
+      The card detection will be done using the GPIO provided.
+
+  non-removable:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Non-removable slot (like eMMC); assume always present.
+
+  # *NOTE* on CD and WP polarity. To use common for all SD/MMC host
+  # controllers line polarity properties, we have to fix the meaning
+  # of the "normal" and "inverted" line levels. We choose to follow
+  # the SDHCI standard, which specifies both those lines as "active
+  # low." Therefore, using the "cd-inverted" property means, that the
+  # CD line is active high, i.e. it is high, when a card is
+  # inserted. Similar logic applies to the "wp-inverted" property.
+  #
+  # CD and WP lines can be implemented on the hardware in one of two
+  # ways: as GPIOs, specified in cd-gpios and wp-gpios properties, or
+  # as dedicated pins. Polarity of dedicated pins can be specified,
+  # using *-inverted properties. GPIO polarity can also be specified
+  # using the GPIO_ACTIVE_LOW flag. This creates an ambiguity in the
+  # latter case. We choose to use the XOR logic for GPIO CD and WP
+  # lines.  This means, the two properties are "superimposed," for
+  # example leaving the GPIO_ACTIVE_LOW flag clear and specifying the
+  # respective *-inverted property property results in a
+  # double-inversion and actually means the "normal" line polarity is
+  # in effect.
+  wp-inverted:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The Write Protect line polarity is inverted.
+
+  cd-inverted:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The CD line polarity is inverted.
+
+  # Other properties
+
+  bus-width:
+    description:
+      Number of data lines.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [1, 4, 8]
+    default: 1
+
+  max-frequency:
+    description: |
+      Maximum operating frequency of the bus:
+        - for eMMC, the maximum supported frequency is 200MHz,
+        - for SD/SDIO cards the SDR104 mode has a max supported
+          frequency of 208MHz,
+        - some mmc host controllers do support a max frequency upto
+          384MHz.
+      So, lets keep the maximum supported value here.
+
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 400000
+    maximum: 384000000
+
+  disable-wp:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      When set, no physical write-protect line is present. This
+      property should only be specified when the controller has a
+      dedicated write-protect detection logic. If a GPIO is always used
+      for the write-protect detection logic, it is sufficient to not
+      specify the wp-gpios property in the absence of a write-protect
+      line. Not used in combination with eMMC or SDIO.
+
+  wp-gpios:
+    maxItems: 1
+    description:
+      GPIO to use for the write-protect detection.
+
+  cd-debounce-delay-ms:
+    description:
+      Set delay time before detecting card after card insert
+      interrupt.
+
+  no-1-8-v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      When specified, denotes that 1.8V card voltage is not supported
+      on this system, even if the controller claims it.
+
+  cap-sd-highspeed:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SD high-speed timing is supported.
+
+  cap-mmc-highspeed:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      MMC high-speed timing is supported.
+
+  sd-uhs-sdr12:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SD UHS SDR12 speed is supported.
+
+  sd-uhs-sdr25:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SD UHS SDR25 speed is supported.
+
+  sd-uhs-sdr50:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SD UHS SDR50 speed is supported.
+
+  sd-uhs-sdr104:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SD UHS SDR104 speed is supported.
+
+  sd-uhs-ddr50:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SD UHS DDR50 speed is supported.
+
+  cap-power-off-card:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Powering off the card is safe.
+
+  cap-mmc-hw-reset:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC hardware reset is supported
+
+  cap-sdio-irq:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      enable SDIO IRQ signalling on this interface
+
+  full-pwr-cycle:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Full power cycle of the card is supported.
+
+  full-pwr-cycle-in-suspend:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Full power cycle of the card in suspend is supported.
+
+  mmc-ddr-1_2v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC high-speed DDR mode (1.2V I/O) is supported.
+
+  mmc-ddr-1_8v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC high-speed DDR mode (1.8V I/O) is supported.
+
+  mmc-ddr-3_3v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC high-speed DDR mode (3.3V I/O) is supported.
+
+  mmc-hs200-1_2v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC HS200 mode (1.2V I/O) is supported.
+
+  mmc-hs200-1_8v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC HS200 mode (1.8V I/O) is supported.
+
+  mmc-hs400-1_2v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC HS400 mode (1.2V I/O) is supported.
+
+  mmc-hs400-1_8v:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC HS400 mode (1.8V I/O) is supported.
+
+  mmc-hs400-enhanced-strobe:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      eMMC HS400 enhanced strobe mode is supported
+
+  no-mmc-hs400:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      All eMMC HS400 modes are not supported.
+
+  dsr:
+    description:
+      Value the card Driver Stage Register (DSR) should be programmed
+      with.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 0xffff
+
+  no-sdio:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Controller is limited to send SDIO commands during
+      initialization.
+
+  no-sd:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Controller is limited to send SD commands during initialization.
+
+  no-mmc:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Controller is limited to send MMC commands during
+      initialization.
+
+  fixed-emmc-driver-type:
+    description:
+      For non-removable eMMC, enforce this driver type. The value is
+      the driver type as specified in the eMMC specification (table
+      206 in spec version 5.1)
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 4
+
+  post-power-on-delay-ms:
+    description:
+      It was invented for MMC pwrseq-simple which could be referred to
+      mmc-pwrseq-simple.yaml. But now it\'s reused as a tunable delay
+      waiting for I/O signalling and card power supply to be stable,
+      regardless of whether pwrseq-simple is used. Default to 10ms if
+      no available.
+    default: 10
+
+  supports-cqe:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The presence of this property indicates that the corresponding
+      MMC host controller supports HW command queue feature.
+
+  disable-cqe-dcmd:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      The presence of this property indicates that the MMC
+      controller\'s command queue engine (CQE) does not support direct
+      commands (DCMDs).
+
+  keep-power-in-suspend:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SDIO only. Preserves card power during a suspend/resume cycle.
+
+  wakeup-source:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      SDIO only. Enables wake up of host system on SDIO IRQ assertion.
+
+  vmmc-supply:
+    description:
+      Supply for the card power
+
+  vqmmc-supply:
+    description:
+      Supply for the bus IO line power, such as a level shifter.
+      If the level shifter is controlled by a GPIO line, this shall
+      be modeled as a "regulator-fixed" with a GPIO line for
+      switching the level shifter on/off.
+
+  mmc-pwrseq:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      System-on-Chip designs may specify a specific MMC power
+      sequence. To successfully detect an (e)MMC/SD/SDIO card, that
+      power sequence must be maintained while initializing the card.
+
+patternProperties:
+  "^.*@[0-9]+$":
+    type: object
+    description: |
+      On embedded systems the cards connected to a host may need
+      additional properties. These can be specified in subnodes to the
+      host controller node. The subnodes are identified by the
+      standard \'reg\' property. Which information exactly can be
+      specified depends on the bindings for the SDIO function driver
+      for the subnode, as specified by the compatible string.
+
+    properties:
+      compatible:
+        description: |
+          Name of SDIO function following generic names recommended
+          practice
+
+      reg:
+        items:
+          - minimum: 0
+            maximum: 7
+            description:
+              Must contain the SDIO function number of the function this
+              subnode describes. A value of 0 denotes the memory SD
+              function, values from 1 to 7 denote the SDIO functions.
+
+    required:
+      - reg
+
+  "^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|uhs-(sdr(12|25|50|104)|ddr50))$":
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+
+    minItems: 2
+    maxItems: 2
+    items:
+      minimum: 0
+      maximum: 359
+      description:
+        Set the clock (phase) delays which are to be configured in the
+        controller while switching to particular speed mode. These values
+        are in pair of degrees.
+
+dependencies:
+  cd-debounce-delay-ms: [ cd-gpios ]
+  fixed-emmc-driver-type: [ non-removable ]
+
+additionalProperties: true
diff --git a/Documentation/devicetree/bindings/mmc/mmc-controller.yaml b/Documentation/devicetree/bindings/mmc/mmc-controller.yaml
index 58ae298cd2fc..99c01ce318d3 100644
--- a/Documentation/devicetree/bindings/mmc/mmc-controller.yaml
+++ b/Documentation/devicetree/bindings/mmc/mmc-controller.yaml
@@ -18,351 +18,13 @@ description: |
   (and the corresponding mmcblkN devices) by defining an alias in the
   /aliases device tree node.
 
+$ref: mmc-controller-common.yaml#
+
 properties:
   $nodename:
     pattern: "^mmc(@.*)?$"
 
-  "#address-cells":
-    const: 1
-    description: |
-      The cell is the slot ID if a function subnode is used.
-
-  "#size-cells":
-    const: 0
-
-  # Card Detection.
-  # If none of these properties are supplied, the host native card
-  # detect will be used. Only one of them should be provided.
-
-  broken-cd:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      There is no card detection available; polling must be used.
-
-  cd-gpios:
-    maxItems: 1
-    description:
-      The card detection will be done using the GPIO provided.
-
-  non-removable:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      Non-removable slot (like eMMC); assume always present.
-
-  # *NOTE* on CD and WP polarity. To use common for all SD/MMC host
-  # controllers line polarity properties, we have to fix the meaning
-  # of the "normal" and "inverted" line levels. We choose to follow
-  # the SDHCI standard, which specifies both those lines as "active
-  # low." Therefore, using the "cd-inverted" property means, that the
-  # CD line is active high, i.e. it is high, when a card is
-  # inserted. Similar logic applies to the "wp-inverted" property.
-  #
-  # CD and WP lines can be implemented on the hardware in one of two
-  # ways: as GPIOs, specified in cd-gpios and wp-gpios properties, or
-  # as dedicated pins. Polarity of dedicated pins can be specified,
-  # using *-inverted properties. GPIO polarity can also be specified
-  # using the GPIO_ACTIVE_LOW flag. This creates an ambiguity in the
-  # latter case. We choose to use the XOR logic for GPIO CD and WP
-  # lines.  This means, the two properties are "superimposed," for
-  # example leaving the GPIO_ACTIVE_LOW flag clear and specifying the
-  # respective *-inverted property property results in a
-  # double-inversion and actually means the "normal" line polarity is
-  # in effect.
-  wp-inverted:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      The Write Protect line polarity is inverted.
-
-  cd-inverted:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      The CD line polarity is inverted.
-
-  # Other properties
-
-  bus-width:
-    description:
-      Number of data lines.
-    $ref: /schemas/types.yaml#/definitions/uint32
-    enum: [1, 4, 8]
-    default: 1
-
-  max-frequency:
-    description: |
-      Maximum operating frequency of the bus:
-        - for eMMC, the maximum supported frequency is 200MHz,
-        - for SD/SDIO cards the SDR104 mode has a max supported
-          frequency of 208MHz,
-        - some mmc host controllers do support a max frequency upto
-          384MHz.
-      So, lets keep the maximum supported value here.
-
-    $ref: /schemas/types.yaml#/definitions/uint32
-    minimum: 400000
-    maximum: 384000000
-
-  disable-wp:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      When set, no physical write-protect line is present. This
-      property should only be specified when the controller has a
-      dedicated write-protect detection logic. If a GPIO is always used
-      for the write-protect detection logic, it is sufficient to not
-      specify the wp-gpios property in the absence of a write-protect
-      line. Not used in combination with eMMC or SDIO.
-
-  wp-gpios:
-    maxItems: 1
-    description:
-      GPIO to use for the write-protect detection.
-
-  cd-debounce-delay-ms:
-    description:
-      Set delay time before detecting card after card insert
-      interrupt.
-
-  no-1-8-v:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      When specified, denotes that 1.8V card voltage is not supported
-      on this system, even if the controller claims it.
-
-  cap-sd-highspeed:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      SD high-speed timing is supported.
-
-  cap-mmc-highspeed:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      MMC high-speed timing is supported.
-
-  sd-uhs-sdr12:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      SD UHS SDR12 speed is supported.
-
-  sd-uhs-sdr25:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      SD UHS SDR25 speed is supported.
-
-  sd-uhs-sdr50:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      SD UHS SDR50 speed is supported.
-
-  sd-uhs-sdr104:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      SD UHS SDR104 speed is supported.
-
-  sd-uhs-ddr50:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      SD UHS DDR50 speed is supported.
-
-  cap-power-off-card:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      Powering off the card is safe.
-
-  cap-mmc-hw-reset:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      eMMC hardware reset is supported
-
-  cap-sdio-irq:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      enable SDIO IRQ signalling on this interface
-
-  full-pwr-cycle:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      Full power cycle of the card is supported.
-
-  full-pwr-cycle-in-suspend:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      Full power cycle of the card in suspend is supported.
-
-  mmc-ddr-1_2v:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      eMMC high-speed DDR mode (1.2V I/O) is supported.
-
-  mmc-ddr-1_8v:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      eMMC high-speed DDR mode (1.8V I/O) is supported.
-
-  mmc-ddr-3_3v:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      eMMC high-speed DDR mode (3.3V I/O) is supported.
-
-  mmc-hs200-1_2v:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      eMMC HS200 mode (1.2V I/O) is supported.
-
-  mmc-hs200-1_8v:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      eMMC HS200 mode (1.8V I/O) is supported.
-
-  mmc-hs400-1_2v:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      eMMC HS400 mode (1.2V I/O) is supported.
-
-  mmc-hs400-1_8v:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      eMMC HS400 mode (1.8V I/O) is supported.
-
-  mmc-hs400-enhanced-strobe:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      eMMC HS400 enhanced strobe mode is supported
-
-  no-mmc-hs400:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      All eMMC HS400 modes are not supported.
-
-  dsr:
-    description:
-      Value the card Driver Stage Register (DSR) should be programmed
-      with.
-    $ref: /schemas/types.yaml#/definitions/uint32
-    minimum: 0
-    maximum: 0xffff
-
-  no-sdio:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      Controller is limited to send SDIO commands during
-      initialization.
-
-  no-sd:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      Controller is limited to send SD commands during initialization.
-
-  no-mmc:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      Controller is limited to send MMC commands during
-      initialization.
-
-  fixed-emmc-driver-type:
-    description:
-      For non-removable eMMC, enforce this driver type. The value is
-      the driver type as specified in the eMMC specification (table
-      206 in spec version 5.1)
-    $ref: /schemas/types.yaml#/definitions/uint32
-    minimum: 0
-    maximum: 4
-
-  post-power-on-delay-ms:
-    description:
-      It was invented for MMC pwrseq-simple which could be referred to
-      mmc-pwrseq-simple.yaml. But now it\'s reused as a tunable delay
-      waiting for I/O signalling and card power supply to be stable,
-      regardless of whether pwrseq-simple is used. Default to 10ms if
-      no available.
-    default: 10
-
-  supports-cqe:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      The presence of this property indicates that the corresponding
-      MMC host controller supports HW command queue feature.
-
-  disable-cqe-dcmd:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      The presence of this property indicates that the MMC
-      controller\'s command queue engine (CQE) does not support direct
-      commands (DCMDs).
-
-  keep-power-in-suspend:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      SDIO only. Preserves card power during a suspend/resume cycle.
-
-  wakeup-source:
-    $ref: /schemas/types.yaml#/definitions/flag
-    description:
-      SDIO only. Enables wake up of host system on SDIO IRQ assertion.
-
-  vmmc-supply:
-    description:
-      Supply for the card power
-
-  vqmmc-supply:
-    description:
-      Supply for the bus IO line power, such as a level shifter.
-      If the level shifter is controlled by a GPIO line, this shall
-      be modeled as a "regulator-fixed" with a GPIO line for
-      switching the level shifter on/off.
-
-  mmc-pwrseq:
-    $ref: /schemas/types.yaml#/definitions/phandle
-    description:
-      System-on-Chip designs may specify a specific MMC power
-      sequence. To successfully detect an (e)MMC/SD/SDIO card, that
-      power sequence must be maintained while initializing the card.
-
-patternProperties:
-  "^.*@[0-9]+$":
-    type: object
-    description: |
-      On embedded systems the cards connected to a host may need
-      additional properties. These can be specified in subnodes to the
-      host controller node. The subnodes are identified by the
-      standard \'reg\' property. Which information exactly can be
-      specified depends on the bindings for the SDIO function driver
-      for the subnode, as specified by the compatible string.
-
-    properties:
-      compatible:
-        description: |
-          Name of SDIO function following generic names recommended
-          practice
-
-      reg:
-        items:
-          - minimum: 0
-            maximum: 7
-            description:
-              Must contain the SDIO function number of the function this
-              subnode describes. A value of 0 denotes the memory SD
-              function, values from 1 to 7 denote the SDIO functions.
-
-    required:
-      - reg
-
-  "^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|uhs-(sdr(12|25|50|104)|ddr50))$":
-    $ref: /schemas/types.yaml#/definitions/uint32-array
-
-    minItems: 2
-    maxItems: 2
-    items:
-      minimum: 0
-      maximum: 359
-      description:
-        Set the clock (phase) delays which are to be configured in the
-        controller while switching to particular speed mode. These values
-        are in pair of degrees.
-
-dependencies:
-  cd-debounce-delay-ms: [ cd-gpios ]
-  fixed-emmc-driver-type: [ non-removable ]
-
-additionalProperties: true
+unevaluatedProperties: true
 
 examples:
   - |

-- 
2.34.1

On Mon, Oct 07, 2024 at 04:03:37PM +0200, Neil Armstrong wrote:
> Move the common MMC "slot" properties because they are shared by the
> single-slot or multi-slot controllers, and will help defining a simple
> mmc-slot bindings document with proper slot properties and nodename.
> 
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
>  .../bindings/mmc/mmc-controller-common.yaml        | 357 +++++++++++++++++++++
>  .../devicetree/bindings/mmc/mmc-controller.yaml    | 344 +-------------------
>  2 files changed, 360 insertions(+), 341 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/mmc/mmc-controller-common.yaml b/Documentation/devicetree/bindings/mmc/mmc-controller-common.yaml
> new file mode 100644
> index 000000000000..e02d3cbcc271
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mmc/mmc-controller-common.yaml
> @@ -0,0 +1,357 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/mmc/mmc-controller-common.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: MMC Controller & Slots Common Properties
> +
> +maintainers:
> +  - Ulf Hansson <ulf.hansson@linaro.org>
> +
> +description: |
> +  These properties are common to multiple MMC host controllers and the
> +  possible slots or ports for multi-slot controllers.
> +
> +properties:
> +  "#address-cells":
> +    const: 1
> +    description: |
> +      The cell is the slot ID if a function subnode is used.

Actually, this comment is wrong. When slot is used, this is still the 
cell size for the mmc bus.

Hi Rob,

On 07/10/2024 22:02, Rob Herring wrote:
> On Mon, Oct 07, 2024 at 04:03:37PM +0200, Neil Armstrong wrote:
>> Move the common MMC "slot" properties because they are shared by the
>> single-slot or multi-slot controllers, and will help defining a simple
>> mmc-slot bindings document with proper slot properties and nodename.
>>
>> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
>> ---
>>   .../bindings/mmc/mmc-controller-common.yaml        | 357 +++++++++++++++++++++
>>   .../devicetree/bindings/mmc/mmc-controller.yaml    | 344 +-------------------
>>   2 files changed, 360 insertions(+), 341 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/mmc/mmc-controller-common.yaml b/Documentation/devicetree/bindings/mmc/mmc-controller-common.yaml
>> new file mode 100644
>> index 000000000000..e02d3cbcc271
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/mmc/mmc-controller-common.yaml
>> @@ -0,0 +1,357 @@
>> +# SPDX-License-Identifier: GPL-2.0
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/mmc/mmc-controller-common.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: MMC Controller & Slots Common Properties
>> +
>> +maintainers:
>> +  - Ulf Hansson <ulf.hansson@linaro.org>
>> +
>> +description: |
>> +  These properties are common to multiple MMC host controllers and the
>> +  possible slots or ports for multi-slot controllers.
>> +
>> +properties:
>> +  "#address-cells":
>> +    const: 1
>> +    description: |
>> +      The cell is the slot ID if a function subnode is used.
> 
> Actually, this comment is wrong. When slot is used, this is still the
> cell size for the mmc bus.

I don't understand, the comment is still valid, MMC slots can have function subnodes
aswell, perhaps the "slot ID" is confusing here ? here it stands for the MMC protocol
slot ID, not the physical slot of the multi-slot MMC controller.

Neil

On 07/10/2024 22:02, Rob Herring wrote:
> On Mon, Oct 07, 2024 at 04:03:37PM +0200, Neil Armstrong wrote:
>> Move the common MMC "slot" properties because they are shared by the
>> single-slot or multi-slot controllers, and will help defining a simple
>> mmc-slot bindings document with proper slot properties and nodename.
>>
>> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
>> ---
>>   .../bindings/mmc/mmc-controller-common.yaml        | 357 +++++++++++++++++++++
>>   .../devicetree/bindings/mmc/mmc-controller.yaml    | 344 +-------------------
>>   2 files changed, 360 insertions(+), 341 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/mmc/mmc-controller-common.yaml b/Documentation/devicetree/bindings/mmc/mmc-controller-common.yaml
>> new file mode 100644
>> index 000000000000..e02d3cbcc271
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/mmc/mmc-controller-common.yaml
>> @@ -0,0 +1,357 @@
>> +# SPDX-License-Identifier: GPL-2.0
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/mmc/mmc-controller-common.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: MMC Controller & Slots Common Properties
>> +
>> +maintainers:
>> +  - Ulf Hansson <ulf.hansson@linaro.org>
>> +
>> +description: |
>> +  These properties are common to multiple MMC host controllers and the
>> +  possible slots or ports for multi-slot controllers.
>> +
>> +properties:
>> +  "#address-cells":
>> +    const: 1
>> +    description: |
>> +      The cell is the slot ID if a function subnode is used.
> 
> Actually, this comment is wrong. When slot is used, this is still the
> cell size for the mmc bus.

OK, not sure how it should be fixed, and it should be fixed before this serie.

Neil

On Mon, 07 Oct 2024 16:03:37 +0200, Neil Armstrong wrote:
> Move the common MMC "slot" properties because they are shared by the
> single-slot or multi-slot controllers, and will help defining a simple
> mmc-slot bindings document with proper slot properties and nodename.
> 
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
>  .../bindings/mmc/mmc-controller-common.yaml        | 357 +++++++++++++++++++++
>  .../devicetree/bindings/mmc/mmc-controller.yaml    | 344 +-------------------
>  2 files changed, 360 insertions(+), 341 deletions(-)
> 

Reviewed-by: Rob Herring (Arm) <robh@kernel.org>

On Mon, Oct 07, 2024 at 04:03:37PM +0200, Neil Armstrong wrote:
> Move the common MMC "slot" properties because they are shared by the
> single-slot or multi-slot controllers, and will help defining a simple
> mmc-slot bindings document with proper slot properties and nodename.
> 
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
>  .../bindings/mmc/mmc-controller-common.yaml        | 357 +++++++++++++++++++++
>  .../devicetree/bindings/mmc/mmc-controller.yaml    | 344 +-------------------
>  2 files changed, 360 insertions(+), 341 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/mmc/mmc-controller-common.yaml b/Documentation/devicetree/bindings/mmc/mmc-controller-common.yaml
> new file mode 100644
> index 000000000000..e02d3cbcc271
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mmc/mmc-controller-common.yaml
> @@ -0,0 +1,357 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/mmc/mmc-controller-common.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: MMC Controller & Slots Common Properties
> +
> +maintainers:
> +  - Ulf Hansson <ulf.hansson@linaro.org>
> +
> +description: |

Don't need '|'.

> +  These properties are common to multiple MMC host controllers and the
> +  possible slots or ports for multi-slot controllers.
> +
> +properties:
> +  "#address-cells":
> +    const: 1
> +    description: |

Ditto.

> +      The cell is the slot ID if a function subnode is used.

On 07/10/2024 21:58, Rob Herring wrote:
> On Mon, Oct 07, 2024 at 04:03:37PM +0200, Neil Armstrong wrote:
>> Move the common MMC "slot" properties because they are shared by the
>> single-slot or multi-slot controllers, and will help defining a simple
>> mmc-slot bindings document with proper slot properties and nodename.
>>
>> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
>> ---
>>   .../bindings/mmc/mmc-controller-common.yaml        | 357 +++++++++++++++++++++
>>   .../devicetree/bindings/mmc/mmc-controller.yaml    | 344 +-------------------
>>   2 files changed, 360 insertions(+), 341 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/mmc/mmc-controller-common.yaml b/Documentation/devicetree/bindings/mmc/mmc-controller-common.yaml
>> new file mode 100644
>> index 000000000000..e02d3cbcc271
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/mmc/mmc-controller-common.yaml
>> @@ -0,0 +1,357 @@
>> +# SPDX-License-Identifier: GPL-2.0
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/mmc/mmc-controller-common.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: MMC Controller & Slots Common Properties
>> +
>> +maintainers:
>> +  - Ulf Hansson <ulf.hansson@linaro.org>
>> +
>> +description: |
> 
> Don't need '|'.
> 
>> +  These properties are common to multiple MMC host controllers and the
>> +  possible slots or ports for multi-slot controllers.
>> +
>> +properties:
>> +  "#address-cells":
>> +    const: 1
>> +    description: |
> 
> Ditto.
> 
>> +      The cell is the slot ID if a function subnode is used.

Right, so I simply moved the yaml definition, shall I fix it in this patch,
before or after ?

Thanks,
Neil