The Raspberry Pi 5 routes the spi0 of the rp1 chip to the pin header.
Add the rp1_spi0 node and its pinctrl node to the devicetree to enable
the spi interface.

Signed-off-by: Gregor Herburger <gregor.herburger@linutronix.de>
---
The RP1 chip, found on the raspberry Pi 5, has nine spi controllers. The
spi0 is routed to the pin header. Add the rp1 nodes and enable it for
the Raspberry Pi 5.
---
Changes in v2:
- Drop first patch as it got already applied: https://lore.kernel.org/lkml/20260903194624.2038562-1-florian.fainelli@broadcom.com/
- add cs gpios to rp1_gpio for pinctrl
- Link to v1: https://patch.msgid.link/20260811-bcm2712-spi-v1-0-4c1708d354bb@linutronix.de
---
 arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b.dts | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b.dts b/arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b.dts
index 0fc57e72632ed..0de3d78100a5d 100644
--- a/arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b.dts
+++ b/arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b.dts
@@ -69,6 +69,20 @@ usb_vbus_default_state: usb-vbus-default-state {
 		groups = "vbus1";
 	};
 
+	rp1_spi0_default_state: rp1-spi0-default-state {
+		function = "spi0";
+		groups = "spi0";
+		bias-disable;
+		drive-strength = <12>;
+		slew-rate = <1>;
+	};
+
+	rp1_spi0_cs_default_state: rp1-spi0-cs-default-state {
+		function = "gpio";
+		pins = "gpio7", "gpio8";
+		bias-pull-up;
+	};
+
 	rp1_i2c4_default_state: rp1-i2c4-default-state {
 		function = "i2c4";
 		groups = "i2c4_2";
@@ -94,6 +108,14 @@ &rp1_i2c6 {
 	pinctrl-names = "default";
 };
 
+&rp1_spi0 {
+	pinctrl-0 = <&rp1_spi0_default_state &rp1_spi0_cs_default_state>;
+	pinctrl-names = "default";
+
+	num-cs = <2>;
+	cs-gpios = <&rp1_gpio 8 GPIO_ACTIVE_LOW &rp1_gpio 7 GPIO_ACTIVE_LOW>;
+};
+
 &rp1_usb0 {
 	pinctrl-0 = <&usb_vbus_default_state>;
 	pinctrl-names = "default";

---
base-commit: db2ddb87143519e20a95aa36c60b36107b736a58
change-id: 20260811-bcm2712-spi-644b70fee3bf

Best regards,
--  
Gregor Herburger <gregor.herburger@linutronix.de>

From: Florian Fainelli <f.fainelli@gmail.com>

On Fri, 04 Sep 2026 11:24:24 +0200, Gregor Herburger <gregor.herburger@linutronix.de> wrote:
> The Raspberry Pi 5 routes the spi0 of the rp1 chip to the pin header.
> Add the rp1_spi0 node and its pinctrl node to the devicetree to enable
> the spi interface.
> 
> Signed-off-by: Gregor Herburger <gregor.herburger@linutronix.de>
> ---

Applied to https://github.com/Broadcom/stblinux/commits/devicetree-arm64/next, thanks!
--
Florian

Hi Gregor,

On 11:24 Fri 04 Sep     , Gregor Herburger wrote:
> The Raspberry Pi 5 routes the spi0 of the rp1 chip to the pin header.
> Add the rp1_spi0 node and its pinctrl node to the devicetree to enable
> the spi interface.

Just a nit-pick: in the comment it's stated that the spi interface is enabled,
which is not true since rp1_usb inherit status="disabled" from its node
definition. This is fine because the user would probably want to enable the
spi interface through some overlay, so no need to resend the patch (at least
for me), so:

Reviewed-by: Andrea della Porta <andrea.porta@suse.com>

Thanks!

Andrea

> 
> Signed-off-by: Gregor Herburger <gregor.herburger@linutronix.de>
> ---
> The RP1 chip, found on the raspberry Pi 5, has nine spi controllers. The
> spi0 is routed to the pin header. Add the rp1 nodes and enable it for
> the Raspberry Pi 5.
> ---
> Changes in v2:
> - Drop first patch as it got already applied: https://lore.kernel.org/lkml/20260903194624.2038562-1-florian.fainelli@broadcom.com/
> - add cs gpios to rp1_gpio for pinctrl
> - Link to v1: https://patch.msgid.link/20260811-bcm2712-spi-v1-0-4c1708d354bb@linutronix.de
> ---
>  arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b.dts | 22 ++++++++++++++++++++++
>  1 file changed, 22 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b.dts b/arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b.dts
> index 0fc57e72632ed..0de3d78100a5d 100644
> --- a/arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b.dts
> +++ b/arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b.dts
> @@ -69,6 +69,20 @@ usb_vbus_default_state: usb-vbus-default-state {
>  		groups = "vbus1";
>  	};
>  
> +	rp1_spi0_default_state: rp1-spi0-default-state {
> +		function = "spi0";
> +		groups = "spi0";
> +		bias-disable;
> +		drive-strength = <12>;
> +		slew-rate = <1>;
> +	};
> +
> +	rp1_spi0_cs_default_state: rp1-spi0-cs-default-state {
> +		function = "gpio";
> +		pins = "gpio7", "gpio8";
> +		bias-pull-up;
> +	};
> +
>  	rp1_i2c4_default_state: rp1-i2c4-default-state {
>  		function = "i2c4";
>  		groups = "i2c4_2";
> @@ -94,6 +108,14 @@ &rp1_i2c6 {
>  	pinctrl-names = "default";
>  };
>  
> +&rp1_spi0 {
> +	pinctrl-0 = <&rp1_spi0_default_state &rp1_spi0_cs_default_state>;
> +	pinctrl-names = "default";
> +
> +	num-cs = <2>;
> +	cs-gpios = <&rp1_gpio 8 GPIO_ACTIVE_LOW &rp1_gpio 7 GPIO_ACTIVE_LOW>;
> +};
> +
>  &rp1_usb0 {
>  	pinctrl-0 = <&usb_vbus_default_state>;
>  	pinctrl-names = "default";
> 
> ---
> base-commit: db2ddb87143519e20a95aa36c60b36107b736a58
> change-id: 20260811-bcm2712-spi-644b70fee3bf
> 
> Best regards,
> --  
> Gregor Herburger <gregor.herburger@linutronix.de>
>

Hi Andrea,

On Fri, Sep 04, 2026 at 12:33:51PM +0200, Andrea della Porta wrote:
> Hi Gregor,
> 
> On 11:24 Fri 04 Sep     , Gregor Herburger wrote:
> > The Raspberry Pi 5 routes the spi0 of the rp1 chip to the pin header.
> > Add the rp1_spi0 node and its pinctrl node to the devicetree to enable
> > the spi interface.
> 
> Just a nit-pick: in the comment it's stated that the spi interface is enabled,
> which is not true since rp1_usb inherit status="disabled" from its node
> definition. This is fine because the user would probably want to enable the
> spi interface through some overlay, so no need to resend the patch (at least
> for me), so:
Indeed. It could be rephrased to:

	Add the rp1_spi0 node and its pinctrl nodes to the devicetree to make
	the spi interface available.

@Florian: Should I send another version or do you want to change it yourself?

Best regards,
-- 
Gregor Herburger
Linutronix GmbH | Bahnhofstrasse 3 | D-88690 Uhldingen-Mühlhofen
Phone: +49 7556 25 999 35; Fax.: +49 7556 25 999 99

Hinweise zum Datenschutz finden Sie hier (Informations on data privacy 
can be found here): https://linutronix.de/legal/data-protection.php

Linutronix GmbH | Firmensitz (Registered Office): Uhldingen-Mühlhofen | 
Registergericht (Registration Court): Amtsgericht Freiburg i.Br., HRB700 
806 | Geschäftsführer (Managing Directors): Dr. Wilfried Wessner, 
Katharina Kopp, Alexander Gieringer

On 9/4/26 03:54, Gregor Herburger wrote:
> Hi Andrea,
> 
> On Fri, Sep 04, 2026 at 12:33:51PM +0200, Andrea della Porta wrote:
>> Hi Gregor,
>>
>> On 11:24 Fri 04 Sep     , Gregor Herburger wrote:
>>> The Raspberry Pi 5 routes the spi0 of the rp1 chip to the pin header.
>>> Add the rp1_spi0 node and its pinctrl node to the devicetree to enable
>>> the spi interface.
>>
>> Just a nit-pick: in the comment it's stated that the spi interface is enabled,
>> which is not true since rp1_usb inherit status="disabled" from its node
>> definition. This is fine because the user would probably want to enable the
>> spi interface through some overlay, so no need to resend the patch (at least
>> for me), so:
> Indeed. It could be rephrased to:
> 
> 	Add the rp1_spi0 node and its pinctrl nodes to the devicetree to make
> 	the spi interface available.
> 
> @Florian: Should I send another version or do you want to change it yourself?

I used that as the new version of your second paragraph, please let me 
know if I should be making further adjustments.

Thanks!
-- 
Florian