This series adds hardware offload for channel-mode mqprio with
TC_MQPRIO_SHAPER_BW_RATE on Marvell octeontx2 PF devices. Each
non-QoS transmit queue is shaped by programming MDQ CIR/PIR on the NIX TX
scheduler. When bandwidth offload is enabled, the driver allocates one
SMQ per queue, parents every MDQ under TL4[0], and applies each traffic
class min/max rate to the queue(s) in that class. The TX scheduler
hierarchy is reprogrammed through ndo_stop()/ndo_open() on every mqprio
add, replace, or delete.
Patch 1 is required for patch 2. The octeontx2 driver tracks committed
mqprio configuration in snapshots keyed by the owning qdisc handle. That
handle is needed to implement two behaviours that patch 2 relies on:
* tc qdisc replace installs the new mqprio and runs its offload setup
before tearing down the replaced instance. Without the handle, the
driver cannot tell a stale disable callback from the replaced qdisc
apart from teardown of the active configuration, and may clear
hardware shapers or netdev TC state while the new mqprio is being
committed.
* When replace fails after partial programming, the driver rolls back
from the previous snapshot. Matching setup and teardown callbacks to
the same qdisc instance requires the handle passed through the core
mqprio offload path.
Patch 1 extends struct tc_mqprio_qopt_offload with that handle and fills
it from mqprio_enable_offload() and mqprio_disable_offload(). Patch 2
consumes it in the octeontx2 PF mqprio offload path.
The driver rejects offload unless the interface is running and the
device supports CIR+PIR shaping. Per-TC rates are rejected when a
traffic class spans more than one queue, and concurrent PFC, XDP, or SDP
rep use is blocked. Ethtool channel count changes are blocked while mqprio
bandwidth offload is active.
Ratheesh Kannoth (2):
net/sched: mqprio: pass qdisc handle to offload drivers
octeontx2-pf: add mqprio bandwidth offload for NIX TX schedulers
.../ethernet/marvell/octeontx2/af/rvu_nix.c | 6 +-
.../marvell/octeontx2/nic/otx2_common.c | 145 +++-
.../marvell/octeontx2/nic/otx2_common.h | 27 +
.../marvell/octeontx2/nic/otx2_dcbnl.c | 6 +
.../marvell/octeontx2/nic/otx2_ethtool.c | 8 +
.../ethernet/marvell/octeontx2/nic/otx2_pf.c | 13 +
.../ethernet/marvell/octeontx2/nic/otx2_tc.c | 696 ++++++++++++++++++
.../net/ethernet/marvell/octeontx2/nic/qos.c | 3 +
include/net/pkt_sched.h | 1 +
net/sched/sch_mqprio.c | 5 +-
10 files changed, 907 insertions(+), 3 deletions(-)
---
v9 -> v10: Addressed sashiko/jacub comments.
https://sashiko.dev/#/message/20260817032747.1765883-1-rkannoth%40marvell.com
v8 -> v9: Addressed Sashiko comments
https://lore.kernel.org/netdev/aoJ6FhtWue0FHDQV@rkannoth-OptiPlex-7090/
v7 -> v8: Addressed Sashiko comments
https://sashiko.dev/#/patchset/20260811085050.3212280-1-rkannoth%40marvell.com
v6 -> v7: Addressed Sashiko comments
https://sashiko.dev/#/message/20260810034738.1786029-1-rkannoth%40marvell.com
v5 -> v6: Addressed Sashiko comments
https://lore.kernel.org/netdev/20260806095434.1144397-1-rkannoth@marvell.com/
v4 -> v5: Addressed sashiko comments
https://sashiko.dev/#/patchset/20260803042724.3380209-1-rkannoth%40marvell.com
v3 -> v4: Addressed sashiko comments
https://lore.kernel.org/netdev/20260729105139.2302908-1-rkannoth@marvell.com/
v2 -> v3: Addressed sashiko comments
https://lore.kernel.org/netdev/amnYX866mYx02cBe@rkannoth-OptiPlex-7090/T/#m67310cbec48b21c7720858ab3a1ea083a0f8dc10
v1 -> v2: Addressed sashiko comments
https://lore.kernel.org/netdev/20260724075010.2665758-1-rkannoth@marvell.com/
--
2.43.0