mpl115_probe() enables runtime PM when a shutdown GPIO is present and
then returns the result of devm_iio_device_register(). If registration
fails, runtime PM remains enabled and autosuspend remains selected.

The same unmanaged runtime PM state is also left behind on driver
unbind, as the IIO device registration is managed but the runtime PM
setup is not.

Use devm_pm_runtime_enable() so runtime PM is disabled automatically
on probe failure and driver unbind. Also unwind the initial
pm_runtime_get_noresume() reference if setting up runtime PM fails
before the matching put.

Fixes: 0c3a333524a3 ("iio: pressure: mpl115: Implementing low power mode by shutdown gpio")
Cc: stable@vger.kernel.org
Signed-off-by: Can Peng <pengcan@kylinos.cn>
---
 drivers/iio/pressure/mpl115.c | 13 +++++++++++--
 1 file changed, 11 insertions(+), 2 deletions(-)

diff --git a/drivers/iio/pressure/mpl115.c b/drivers/iio/pressure/mpl115.c
index 16e112b796ba..9e77b76bd1fa 100644
--- a/drivers/iio/pressure/mpl115.c
+++ b/drivers/iio/pressure/mpl115.c
@@ -204,8 +204,17 @@ int mpl115_probe(struct device *dev, const char *name,
 	if (data->shutdown) {
 		/* Enable runtime PM */
 		pm_runtime_get_noresume(dev);
-		pm_runtime_set_active(dev);
-		pm_runtime_enable(dev);
+		ret = pm_runtime_set_active(dev);
+		if (ret) {
+			pm_runtime_put_noidle(dev);
+			return ret;
+		}
+
+		ret = devm_pm_runtime_enable(dev);
+		if (ret) {
+			pm_runtime_put_noidle(dev);
+			return ret;
+		}
 
 		/*
 		 * As the device takes 3 ms to come up with a fresh
-- 
2.53.0

On Sat, 18 Jul 2026 14:19:09 +0800
Can Peng <pengcan@kylinos.cn> wrote:

> mpl115_probe() enables runtime PM when a shutdown GPIO is present and
> then returns the result of devm_iio_device_register(). If registration
> fails, runtime PM remains enabled and autosuspend remains selected.
> 
> The same unmanaged runtime PM state is also left behind on driver
> unbind, as the IIO device registration is managed but the runtime PM
> setup is not.
> 
> Use devm_pm_runtime_enable() so runtime PM is disabled automatically
> on probe failure and driver unbind. Also unwind the initial
> pm_runtime_get_noresume() reference if setting up runtime PM fails
> before the matching put.
> 
> Fixes: 0c3a333524a3 ("iio: pressure: mpl115: Implementing low power mode by shutdown gpio")
> Cc: stable@vger.kernel.org
> Signed-off-by: Can Peng <pengcan@kylinos.cn>
Hi Can Peng,

A similar code pattern came up recently based as bold claim from sashiko
that autosuspend won't kick in if we don't do a get / put pair.

Turned out not to be true.  If no one touches the runtime pm counts
and turns runtime pm on, then this line:
https://elixir.bootlin.com/linux/v7.1.3/source/drivers/base/dd.c#L872
becomes relevant.    That ends up calling auto suspend.
Please chase through this call sequence just in case we got it wrong!

Hence I believe this is a simplification change that can be made here.

> ---
>  drivers/iio/pressure/mpl115.c | 13 +++++++++++--
>  1 file changed, 11 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/iio/pressure/mpl115.c b/drivers/iio/pressure/mpl115.c
> index 16e112b796ba..9e77b76bd1fa 100644
> --- a/drivers/iio/pressure/mpl115.c
> +++ b/drivers/iio/pressure/mpl115.c
> @@ -204,8 +204,17 @@ int mpl115_probe(struct device *dev, const char *name,
>  	if (data->shutdown) {
>  		/* Enable runtime PM */
>  		pm_runtime_get_noresume(dev);
Drop this get_noresume()

> -		pm_runtime_set_active(dev);
> -		pm_runtime_enable(dev);
> +		ret = pm_runtime_set_active(dev);
> +		if (ret) {
> +			pm_runtime_put_noidle(dev);
No need for the put here
> +			return ret;
> +		}
> +
> +		ret = devm_pm_runtime_enable(dev);
> +		if (ret) {
> +			pm_runtime_put_noidle(dev);
or here.

The switch to devm_pm_runtime_enable() and error checks all look good
to me.

> +			return ret;
> +		}
>  
>  		/*
>  		 * As the device takes 3 ms to come up with a fresh

and the pm_runtime_put() at end of this block

We don't mind if auto runtime suspend happens a tiny bit later.