This patch series introduces support for the AAEON SRG-IMX8P embedded
controller (MCU). The MCU is connected via I2C and provides GPIO and
watchdog functionality for the SRG-IMX8P board.
The series includes:
- Device tree binding for the MFD driver
- MFD driver that serves as the core driver for the MCU
- GPIO driver implementing the GPIO functionality
- Watchdog driver for system monitoring
- MAINTAINERS entry for the new drivers
The drivers follow the standard Linux kernel subsystem patterns, with
the MFD driver registering the sub-devices (GPIO and watchdog) which
are then handled by their respective subsystem drivers.
Signed-off-by: Thomas Perrot (Schneider Electric) <thomas.perrot@bootlin.com>
---
Changes in v5:
- mfd: use heap-allocated DMA-safe buffers for I2C transfers, replacing
stack-allocated buffers in the regmap bus callbacks
- mfd: switch from REGCACHE_NONE to REGCACHE_MAPLE; add volatile_reg
callback marking GPIO input read registers (opcode 0x72) as volatile;
add max_register
- mfd: use PLATFORM_DEVID_AUTO instead of PLATFORM_DEVID_NONE
- mfd: use MFD_CELL_BASIC() macro for cell definitions
- mfd: use dev_err_probe() for regmap initialization error
- Link to v4: https://lore.kernel.org/r/20260324-dev-b4-aaeon-mcu-driver-v4-0-afb011df4794@bootlin.com
Changes in v4:
- mfd: switch to a custom regmap bus; remove aaeon_mcu_i2c_xfer() and the aaeon_mcu_dev struct
- mfd: locking delegated to regmap's built-in mutex; drop explicit mutex
- mfd: remove firmware version reading at probe time
- gpio, watchdog: use regmap_read()/regmap_write() via dev_get_regmap()
- include: replace aaeon_mcu_i2c_xfer() declaration with AAEON_MCU_REG() macro
- dt-bindings: remove unused label from example node
- Link to v3: https://lore.kernel.org/r/20260203-dev-b4-aaeon-mcu-driver-v3-0-0a19432076ac@bootlin.com
Changes in v3:
- Renamed SRG-IMX8PL to SRG-IMX8P
- dt-bindings: add gpio-controller properties as required
- mfd: move struct aaeon_mcu_dev from header to .c file (private)
- mfd: use guard(mutex) and devm_mutex_init() for cleanup
- mfd: firmware version log changed to dev_dbg()
- mfd: add select MFD_CORE to Kconfig
- Kconfig: add || COMPILE_TEST to all three drivers
- watchdog: add comments explaining hardware timeout and WDOG_HW_RUNNING
- watchdog: remove unused platform_set_drvdata()
- watchdog: add a function to query the status
- Link to v2: https://lore.kernel.org/r/20260123-dev-b4-aaeon-mcu-driver-v2-0-9f4c00bfb5cb@bootlin.com
Changes in v2:
- Fold GPIO and watchdog bindings into MFD binding
- Drop OF_GPIO dependency in GPIO Kconfig
- Use __set_bit/__clear_bit/__assign_bit instead of atomic variants
- Various driver cleanups and improvements
- Link to v1: https://lore.kernel.org/r/20251212-dev-b4-aaeon-mcu-driver-v1-0-6bd65bc8ef12@bootlin.com
---
Thomas Perrot (Schneider Electric) (5):
dt-bindings: vendor-prefixes: Add AAEON vendor prefix
dt-bindings: mfd: Add AAEON embedded controller
mfd: aaeon: Add SRG-IMX8P MCU driver
gpio: aaeon: Add GPIO driver for SRG-IMX8P MCU
watchdog: aaeon: Add watchdog driver for SRG-IMX8P MCU
.../bindings/mfd/aaeon,srg-imx8p-mcu.yaml | 67 ++++++
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
MAINTAINERS | 10 +
drivers/gpio/Kconfig | 9 +
drivers/gpio/Makefile | 1 +
drivers/gpio/gpio-aaeon-mcu.c | 229 +++++++++++++++++++++
drivers/mfd/Kconfig | 10 +
drivers/mfd/Makefile | 1 +
drivers/mfd/aaeon-mcu.c | 204 ++++++++++++++++++
drivers/watchdog/Kconfig | 10 +
drivers/watchdog/Makefile | 1 +
drivers/watchdog/aaeon_mcu_wdt.c | 132 ++++++++++++
include/linux/mfd/aaeon-mcu.h | 40 ++++
13 files changed, 716 insertions(+)
---
base-commit: d358e5254674b70f34c847715ca509e46eb81e6f
change-id: 20251211-dev-b4-aaeon-mcu-driver-e0e89ebf4afb
Best regards,
--
Thomas Perrot (Schneider Electric) <thomas.perrot@bootlin.com>