Documentation describes the required and optional properties for
implementing Device Tree for a Microsoft G6 Touch Digitizer that
supports HID over SPI Protocol 1.0 specification.
The properties are common to HID over SPI.
Signed-off-by: Dmitry Antipov <dmanti@microsoft.com>
Signed-off-by: Jarrett Schultz <jaschultz@microsoft.com>
Signed-off-by: Jingyuan Liang <jingyliang@chromium.org>
---
.../devicetree/bindings/input/hid-over-spi.yaml | 126 +++++++++++++++++++++
1 file changed, 126 insertions(+)
diff --git a/Documentation/devicetree/bindings/input/hid-over-spi.yaml b/Documentation/devicetree/bindings/input/hid-over-spi.yaml
new file mode 100644
index 000000000000..d1b0a2e26c32
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/hid-over-spi.yaml
@@ -0,0 +1,126 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/hid-over-spi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: HID over SPI Devices
+
+maintainers:
+ - Benjamin Tissoires <benjamin.tissoires@redhat.com>
+ - Jiri Kosina <jkosina@suse.cz>
+
+description: |+
+ HID over SPI provides support for various Human Interface Devices over the
+ SPI bus. These devices can be for example touchpads, keyboards, touch screens
+ or sensors.
+
+ The specification has been written by Microsoft and is currently available
+ here: https://www.microsoft.com/en-us/download/details.aspx?id=103325
+
+ If this binding is used, the kernel module spi-hid will handle the
+ communication with the device and the generic hid core layer will handle the
+ protocol.
+
+allOf:
+ - $ref: /schemas/input/touchscreen/touchscreen.yaml#
+
+properties:
+ compatible:
+ oneOf:
+ - items:
+ - enum:
+ - microsoft,g6-touch-digitizer
+ - const: hid-over-spi
+ - description: Just "hid-over-spi" alone is allowed, but not recommended.
+ const: hid-over-spi
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ reset-gpios:
+ maxItems: 1
+ description:
+ GPIO specifier for the digitizer's reset pin (active low). The line must
+ be flagged with GPIO_ACTIVE_LOW.
+
+ vdd-supply:
+ description:
+ Regulator for the VDD supply voltage.
+
+ input-report-header-address:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 0xffffff
+ description:
+ A value to be included in the Read Approval packet, listing an address of
+ the input report header to be put on the SPI bus. This address has 24
+ bits.
+
+ input-report-body-address:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 0xffffff
+ description:
+ A value to be included in the Read Approval packet, listing an address of
+ the input report body to be put on the SPI bus. This address has 24 bits.
+
+ output-report-address:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 0xffffff
+ description:
+ A value to be included in the Output Report sent by the host, listing an
+ address where the output report on the SPI bus is to be written to. This
+ address has 24 bits.
+
+ read-opcode:
+ $ref: /schemas/types.yaml#/definitions/uint8
+ description:
+ Value to be used in Read Approval packets. 1 byte.
+
+ write-opcode:
+ $ref: /schemas/types.yaml#/definitions/uint8
+ description:
+ Value to be used in Write Approval packets. 1 byte.
+
+required:
+ - compatible
+ - interrupts
+ - reset-gpios
+ - vdd-supply
+ - input-report-header-address
+ - input-report-body-address
+ - output-report-address
+ - read-opcode
+ - write-opcode
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/gpio/gpio.h>
+
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hid@0 {
+ compatible = "microsoft,g6-touch-digitizer", "hid-over-spi";
+ reg = <0x0>;
+ interrupts-extended = <&gpio 42 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
+ vdd-supply = <&pm8350c_l3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_d6_int_bias>;
+ input-report-header-address = <0x1000>;
+ input-report-body-address = <0x1004>;
+ output-report-address = <0x2000>;
+ read-opcode = /bits/ 8 <0x0b>;
+ write-opcode = /bits/ 8 <0x02>;
+ };
+ };
--
2.53.0.1185.g05d4b7b318-goog