Add the sound card of Glymur-crd board with the routing for Speakers.

Add device nodes for the sound support with WSA884x smart speakers
and playback via speakers and recording via DMIC microphones.

Co-developed-by: Mohammad Rafi Shaik <mohammad.rafi.shaik@oss.qualcomm.com>
Signed-off-by: Mohammad Rafi Shaik <mohammad.rafi.shaik@oss.qualcomm.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/glymur-crd.dts | 110 ++++++++++++++++++++++++
 1 file changed, 110 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/glymur-crd.dts b/arch/arm64/boot/dts/qcom/glymur-crd.dts
index 6b7f91a3a968..39e15184940b 100644
--- a/arch/arm64/boot/dts/qcom/glymur-crd.dts
+++ b/arch/arm64/boot/dts/qcom/glymur-crd.dts
@@ -121,6 +121,54 @@ vreg_wwan: regulator-wwan {
 		pinctrl-0 = <&wwan_reg_en>;
 		pinctrl-names = "default";
 	};
+
+	sound {
+		compatible = "qcom,glymur-sndcard";
+		model = "GLYMUR-CRD";
+		audio-routing = "WooferLeft IN", "WSA WSA_SPK1 OUT",
+				"TweeterLeft IN", "WSA WSA_SPK2 OUT",
+				"WooferRight IN", "WSA2 WSA_SPK2 OUT",
+				"TweeterRight IN", "WSA2 WSA_SPK2 OUT",
+				"VA DMIC0", "vdd-micb",
+				"VA DMIC1", "vdd-micb",
+				"VA DMIC2", "vdd-micb",
+				"VA DMIC3", "vdd-micb";
+
+		wsa-dai-link {
+			link-name = "WSA Playback";
+
+			cpu {
+				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+			};
+
+			codec {
+				sound-dai = <&left_woofer>, <&left_tweeter>,
+					    <&swr0 0>, <&lpass_wsamacro 0>,
+					    <&right_woofer>, <&right_tweeter>,
+					    <&swr3 0>, <&lpass_wsa2macro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		va-dai-link {
+			link-name = "VA Capture";
+
+			codec {
+				sound-dai = <&lpass_vamacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+	};
 };
 
 &apps_rsc {
@@ -367,6 +415,12 @@ vreg_l4h_e0_1p2: ldo4 {
 	};
 };
 
+&lpass_vamacro {
+	pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
+	pinctrl-names = "default";
+	qcom,dmic-sample-rate = <4800000>;
+};
+
 &pcie3b {
 	vddpe-3v3-supply = <&vreg_nvmesec>;
 
@@ -485,6 +539,62 @@ &pon_resin {
 	status = "okay";
 };
 
+&swr0 {
+	status = "okay";
+
+	/* WSA8845, Left Woofer */
+	left_woofer: speaker@0,0 {
+		compatible = "sdw20217020400";
+		reg = <0 0>;
+		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "WooferLeft";
+		vdd-1p8-supply = <&vreg_l15b_e0_1p8>;
+		vdd-io-supply = <&vreg_l18b_e0_1p2>;
+		qcom,port-mapping = <1 2 3 7 12 14>;
+	};
+
+	/* WSA8845, Left Tweeter */
+	left_tweeter: speaker@0,1 {
+		compatible = "sdw20217020400";
+		reg = <0 1>;
+		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "TweeterLeft";
+		vdd-1p8-supply = <&vreg_l15b_e0_1p8>;
+		vdd-io-supply = <&vreg_l18b_e0_1p2>;
+		qcom,port-mapping = <4 5 6 7 13 15>;
+	};
+};
+
+&swr3 {
+	status = "okay";
+
+	/* WSA8845, Right Woofer */
+	right_woofer: speaker@0,0 {
+		compatible = "sdw20217020400";
+		reg = <0 0>;
+		reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "WooferRight";
+		vdd-1p8-supply = <&vreg_l15b_e0_1p8>;
+		vdd-io-supply = <&vreg_l18b_e0_1p2>;
+		qcom,port-mapping = <1 2 3 7 12 14>;
+	};
+
+	/* WSA8845, Right Tweeter */
+	right_tweeter: speaker@0,1 {
+		compatible = "sdw20217020400";
+		reg = <0 1>;
+		reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "TweeterRight";
+		vdd-1p8-supply = <&vreg_l15b_e0_1p8>;
+		vdd-io-supply = <&vreg_l18b_e0_1p2>;
+		qcom,port-mapping = <4 5 6 7 13 15>;
+	};
+};
+
 &remoteproc_adsp {
 	firmware-name = "qcom/glymur/adsp.mbn",
 			"qcom/glymur/adsp_dtb.mbn";
-- 
2.47.3

On 3/11/26 1:42 PM, Srinivas Kandagatla wrote:
> Add the sound card of Glymur-crd board with the routing for Speakers.
> 
> Add device nodes for the sound support with WSA884x smart speakers

Smart speaker amps?

[...]

> +		wsa-dai-link {
> +			link-name = "WSA Playback";
> +
> +			cpu {

'co'dec < 'cp'u, the other node is correct

Other than that

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad