Add device tree for the Qualcomm / Lantronix SDM845 HDK. It is the
development platform using the modem-less (SDA845) SoC, optional onboard
DSI panel and a rich set of connectors.

Working:
- HDMI display
- uSD, UFS, USB
- DSPs, WiFi, BT
- Buttons, LEDs

Not working or not tested:
- DisplayPort - TCPM not supported for this PMIC
- WiGig - requires power sequencing driver, doesn't work with the
  current in-kernel driver
- Audio
- FingerPrint
- USIM

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile       |   1 +
 arch/arm64/boot/dts/qcom/sdm845-hdk.dts | 820 ++++++++++++++++++++++++++++++++
 2 files changed, 821 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index f80b5d9cf1e8..dc901a0fa8b3 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -272,6 +272,7 @@ sdm845-db845c-navigation-mezzanine-dtbs	:= sdm845-db845c.dtb sdm845-db845c-navig
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-db845c-navigation-mezzanine.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-google-crosshatch.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-google-blueline.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-hdk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-lg-judyln.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-lg-judyp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-mtp.dtb
diff --git a/arch/arm64/boot/dts/qcom/sdm845-hdk.dts b/arch/arm64/boot/dts/qcom/sdm845-hdk.dts
new file mode 100644
index 000000000000..4dd426912d20
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-hdk.dts
@@ -0,0 +1,820 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sdm845.dtsi"
+#include "pm8005.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SDM845 HDK";
+	compatible = "qcom,sdm845-hdk", "qcom,sdm845";
+	chassis-type = "embedded";
+
+	aliases {
+		serial0 = &uart9;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&home_pin_a>, <&vol_up_pin_a>;
+
+		key-home {
+			label = "Home";
+			linux,code = <KEY_HOMEPAGE>;
+			gpios = <&pm8998_gpios 5 GPIO_ACTIVE_LOW>;
+		};
+
+		key-vol-up {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm8998_gpios 6 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&lt9611_out>;
+			};
+		};
+	};
+
+	/*
+	 * Apparently RPMh does not provide support for PM8998 S4 and S6
+	 * because they are always-on; model them as fixed regulators.
+	 */
+	vreg_s4a_1p8: regulator-pm8998-smps4 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_s4a_1p8";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	vreg_s6a_0p8: regulator-pm8998-smps6 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_s6a_0p8";
+
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <800000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	vreg_sys_bob_3p3: regulator-sys-bob {
+		compatible = "regulator-fixed";
+		regulator-name = "sys_bob";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&vreg_s4a_1p8>;
+	};
+
+	vph_pwr: regulator-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
+};
+
+&adsp_pas {
+	firmware-name = "qcom/sdm845/adsp.mbn";
+
+	status = "okay";
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm8998-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-s9-supply = <&vph_pwr>;
+		vdd-s10-supply = <&vph_pwr>;
+		vdd-s11-supply = <&vph_pwr>;
+		vdd-s12-supply = <&vph_pwr>;
+		vdd-s13-supply = <&vph_pwr>;
+		vdd-l1-l27-supply = <&vreg_s7a_1p025>;
+		vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
+		vdd-l3-l11-supply = <&vreg_s7a_1p025>;
+		vdd-l4-l5-supply = <&vreg_s7a_1p025>;
+		vdd-l6-supply = <&vph_pwr>;
+		vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
+		vdd-l9-supply = <&vreg_bob>;
+		vdd-l10-l23-l25-supply = <&vreg_bob>;
+		vdd-l13-l19-l21-supply = <&vreg_bob>;
+		vdd-l16-l28-supply = <&vreg_bob>;
+		vdd-l18-l22-supply = <&vreg_bob>;
+		vdd-l20-l24-supply = <&vreg_bob>;
+		vdd-l26-supply = <&vreg_s3a_1p35>;
+		vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
+
+		vreg_s2a_1p125: smps2 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+		};
+
+		vreg_s3a_1p35: smps3 {
+			regulator-min-microvolt = <1352000>;
+			regulator-max-microvolt = <1352000>;
+		};
+
+		vreg_s5a_2p04: smps5 {
+			regulator-min-microvolt = <1904000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		vreg_s7a_1p025: smps7 {
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <1028000>;
+		};
+
+		vreg_l1a_0p88: ldo1 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2a_1p2: ldo2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l3a_1p0: ldo3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5a_0p8: ldo5 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6a_1p85: ldo6 {
+			regulator-min-microvolt = <1856000>;
+			regulator-max-microvolt = <1856000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a_1p8: ldo7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8a_1p2: ldo8 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1248000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9a_1p8: ldo9 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10a_1p8: ldo10 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11a_1p0: ldo11 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1048000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12a_1p8: ldo12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13a_2p95: ldo13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14a_1p8: ldo14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15a_1p8: ldo15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l16a_2p7: ldo16 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2704000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17a_1p3: ldo17 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l18a_2p7: ldo18 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l19a_3p0: ldo19 {
+			regulator-min-microvolt = <2856000>;
+			regulator-max-microvolt = <3104000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l20a_2p95: ldo20 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l21a_2p95: ldo21 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l22a_2p85: ldo22 {
+			regulator-min-microvolt = <2864000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l23a_3p3: ldo23 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l24a_3p075: ldo24 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l25a_3p3: ldo25 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l26a_1p2: ldo26 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l28a_3p0: ldo28 {
+			regulator-min-microvolt = <2856000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_lvs1a_1p8: lvs1 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_lvs2a_1p8: lvs2 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pmi8998-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-bob-supply = <&vph_pwr>;
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3600000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+			regulator-allow-bypass;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pm8005-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+
+		vreg_s3c_0p6: smps3 {
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <600000>;
+		};
+	};
+};
+
+&cluster_sleep_0 {
+	/* default, 0x4100c244, kills the board */
+	arm,psci-suspend-param = <0x41008244>;
+};
+
+&cdsp_pas {
+	firmware-name = "qcom/sdm845/cdsp.mbn";
+
+	status = "okay";
+};
+
+&gcc {
+	protected-clocks = <GCC_QSPI_CORE_CLK>,
+			   <GCC_QSPI_CORE_CLK_SRC>,
+			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+			   <GCC_LPASS_Q6_AXI_CLK>,
+			   <GCC_LPASS_SWAY_CLK>;
+};
+
+&gpi_dma0 {
+	status = "okay";
+};
+
+&gpi_dma1 {
+	status = "okay";
+};
+
+&gpu {
+	status = "okay";
+};
+
+&gpu_zap_shader {
+	firmware-name = "qcom/sdm845/a630_zap.mbn";
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	lt9611_codec: hdmi-bridge@3b {
+		compatible = "lontium,lt9611";
+		reg = <0x3b>;
+		#sound-dai-cells = <1>;
+
+		interrupts-extended = <&tlmm 113 IRQ_TYPE_EDGE_FALLING>;
+
+		reset-gpios = <&tlmm 76 GPIO_ACTIVE_HIGH>;
+
+		vdd-supply = <&vreg_s4a_1p8>;
+		vcc-supply = <&vreg_sys_bob_3p3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lt9611_irq_pin>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lt9611_a: endpoint {
+					remote-endpoint = <&mdss_dsi0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				lt9611_b: endpoint {
+					remote-endpoint = <&mdss_dsi1_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				lt9611_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+		};
+	};
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	status = "okay";
+	vdda-supply = <&vreg_l26a_1p2>;
+
+	qcom,dual-dsi-mode;
+	qcom,master-dsi;
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&lt9611_a>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	status = "okay";
+	vdds-supply = <&vreg_s6a_0p8>;
+};
+
+&mdss_dsi1 {
+	vdda-supply = <&vreg_l26a_1p2>;
+
+	qcom,dual-dsi-mode;
+
+	/* DSI1 is slave, so use DSI0 clocks */
+	assigned-clock-parents = <&mdss_dsi0_phy DSI_BYTE_PLL_CLK>,
+				 <&mdss_dsi0_phy DSI_PIXEL_PLL_CLK>;
+
+	status = "okay";
+};
+
+&mdss_dsi1_out {
+	remote-endpoint = <&lt9611_b>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi1_phy {
+	vdds-supply = <&vreg_s6a_0p8>;
+	status = "okay";
+};
+
+&mss_pil {
+	firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mbn";
+
+	status = "okay";
+};
+
+&pcie0 {
+	perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&pcie0_default_state>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie0_phy {
+	vdda-phy-supply = <&vreg_l1a_0p88>;
+	vdda-pll-supply = <&vreg_l26a_1p2>;
+
+	status = "okay";
+};
+
+&pcie1 {
+	perst-gpios = <&tlmm 102 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie1_default_state>;
+
+	status = "okay";
+};
+
+&pcie1_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l1a_0p88>;
+	vdda-pll-supply = <&vreg_l26a_1p2>;
+};
+
+&pm8998_gpios {
+	home_pin_a: home-active-state {
+		pins = "gpio6";
+		function = "normal";
+		input-enable;
+		bias-pull-up;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+	};
+
+	vol_up_pin_a: vol-up-active-state {
+		pins = "gpio6";
+		function = "normal";
+		input-enable;
+		bias-pull-up;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+	};
+};
+
+&pm8998_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+
+	status = "okay";
+};
+
+&pmi8998_lpg {
+	status = "okay";
+
+	qcom,power-source = <1>;
+
+	led@3 {
+		reg = <3>;
+		color = <LED_COLOR_ID_BLUE>;
+		function = LED_FUNCTION_BLUETOOTH;
+		linux,default-trigger = "bluetooth-power";
+	};
+
+	led@4 {
+		reg = <4>;
+		color = <LED_COLOR_ID_GREEN>;
+		function = LED_FUNCTION_HEARTBEAT;
+		linux,default-trigger = "heartbeat";
+		function-enumerator = <2>;
+	};
+
+	led@5 {
+		reg = <5>;
+		color = <LED_COLOR_ID_RED>;
+		function = LED_FUNCTION_INDICATOR;
+		function-enumerator = <1>;
+	};
+};
+
+&pmi8998_wled {
+	status = "disabled";
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
+	pinctrl-names = "default";
+
+	vmmc-supply = <&vreg_l21a_2p95>;
+	vqmmc-supply = <&vreg_l13a_2p95>;
+
+	bus-width = <4>;
+	cd-gpios = <&tlmm 126 GPIO_ACTIVE_LOW>;
+};
+
+&slpi_pas {
+	firmware-name = "qcom/sdm845/Qualcomm/SDM845-HDK/slpi.mbn";
+
+	status = "okay";
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, /* SPI (eSE - embedded Secure Element) */
+			       <81 4>; /* SPI (fingerprint reader) */
+
+	lt9611_irq_pin: lt9611-irq-state {
+		pins = "gpio113";
+		function = "gpio";
+		bias-disable;
+	};
+
+	pcie0_default_state: pcie0-default-state {
+		clkreq-pins {
+			pins = "gpio36";
+			function = "pci_e0";
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio35";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		wake-n-pins {
+			pins = "gpio37";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	pcie1_default_state: pcie1-default-state {
+		clkreq-pins {
+			pins = "gpio103";
+			function = "pci_e1";
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio102";
+			function = "gpio";
+			drive-strength = <16>;
+			bias-pull-down;
+		};
+
+		wake-n-pins {
+			pins = "gpio104";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_default_state: sdc2-default-state {
+		clk-pins {
+			pins = "sdc2_clk";
+			bias-disable;
+
+			/*
+			 * It seems that mmc_test reports errors if drive
+			 * strength is not 16 on clk, cmd, and data pins.
+			 */
+			drive-strength = <16>;
+		};
+
+		cmd-pins {
+			pins = "sdc2_cmd";
+			bias-pull-up;
+			drive-strength = <10>;
+		};
+
+		data-pins {
+			pins = "sdc2_data";
+			bias-pull-up;
+			drive-strength = <10>;
+		};
+	};
+
+	sdc2_card_det_n: sd-card-det-n-state {
+		pins = "gpio126";
+		function = "gpio";
+		bias-pull-up;
+	};
+};
+
+&uart6 {
+	pinctrl-0 = <&qup_uart6_4pin>;
+
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3990-bt";
+
+		vddio-supply = <&vreg_s4a_1p8>;
+		vddxo-supply = <&vreg_l7a_1p8>;
+		vddrf-supply = <&vreg_l17a_1p3>;
+		vddch0-supply = <&vreg_l25a_3p3>;
+		max-speed = <3200000>;
+	};
+};
+
+&uart9 {
+	status = "okay";
+};
+
+&ufs_mem_hc {
+	status = "okay";
+
+	reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l20a_2p95>;
+	vcc-max-microamp = <800000>;
+};
+
+&ufs_mem_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l1a_0p88>;
+	vdda-pll-supply = <&vreg_l26a_1p2>;
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+	status = "okay";
+
+	vdd-supply = <&vreg_l1a_0p88>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+
+	qcom,imp-res-offset-value = <8>;
+	qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
+	qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
+	qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+};
+
+&usb_1_qmpphy {
+	vdda-phy-supply = <&vreg_l26a_1p2>;
+	vdda-pll-supply = <&vreg_l1a_0p88>;
+
+	status = "okay";
+};
+
+/* HS only */
+&usb_2 {
+	qcom,select-utmi-as-pipe-clk;
+
+	status = "okay";
+};
+
+&usb_2_dwc3 {
+	maximum-speed = "high-speed";
+	phys = <&usb_2_hsphy>;
+	phy-names = "usb2-phy";
+
+	dr_mode = "host";
+};
+
+&usb_2_hsphy {
+	vdd-supply = <&vreg_l1a_0p88>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+
+	qcom,imp-res-offset-value = <8>;
+	qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>;
+
+	status = "okay";
+};
+
+&venus {
+	status = "okay";
+};
+
+&wifi {
+	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+	vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
+
+	qcom,snoc-host-cap-8bit-quirk;
+	qcom,calibration-variant = "Qualcomm_sdm845hdk";
+
+	status = "okay";
+};
+
+/* PINCTRL - additions to nodes defined in sdm845.dtsi */
+&qup_uart9_rx {
+	drive-strength = <2>;
+	bias-pull-up;
+};
+
+&qup_uart9_tx {
+	drive-strength = <2>;
+	bias-disable;
+};

-- 
2.47.3

On 2/17/26 10:20 PM, Dmitry Baryshkov wrote:
> Add device tree for the Qualcomm / Lantronix SDM845 HDK. It is the
> development platform using the modem-less (SDA845) SoC, optional onboard
> DSI panel and a rich set of connectors.
> 
> Working:
> - HDMI display
> - uSD, UFS, USB
> - DSPs, WiFi, BT
> - Buttons, LEDs
> 
> Not working or not tested:
> - DisplayPort - TCPM not supported for this PMIC
> - WiGig - requires power sequencing driver, doesn't work with the
>   current in-kernel driver
> - Audio
> - FingerPrint
> - USIM
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
> ---

[...]

> +	gpio-keys {
> +		compatible = "gpio-keys";
> +		autorepeat;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&home_pin_a>, <&vol_up_pin_a>;

property-n
property-names

in this order, file-wide, please

[...]

> +&cluster_sleep_0 {
> +	/* default, 0x4100c244, kills the board */
> +	arm,psci-suspend-param = <0x41008244>;
> +};

Does crashdump say anything interesting?

[...]

> +&mdss_dsi1_phy {
> +	vdds-supply = <&vreg_s6a_0p8>;
> +	status = "okay";

Let's uniformly keep a \n above 'status'

[...]

> +&pm8998_gpios {
> +	home_pin_a: home-active-state {
> +		pins = "gpio6";

gpio5 here

[...]

> +&pmi8998_lpg {
> +	status = "okay";
> +
> +	qcom,power-source = <1>;
> +
> +	led@3 {
> +		reg = <3>;
> +		color = <LED_COLOR_ID_BLUE>;
> +		function = LED_FUNCTION_BLUETOOTH;
> +		linux,default-trigger = "bluetooth-power";
> +	};
> +
> +	led@4 {
> +		reg = <4>;
> +		color = <LED_COLOR_ID_GREEN>;
> +		function = LED_FUNCTION_HEARTBEAT;
> +		linux,default-trigger = "heartbeat";
> +		function-enumerator = <2>;

function-enumerators only seem necessary when the same color&func
combo is registered multiple times

> +	};
> +
> +	led@5 {
> +		reg = <5>;
> +		color = <LED_COLOR_ID_RED>;
> +		function = LED_FUNCTION_INDICATOR;
> +		function-enumerator = <1>;

panic-indicator?

> +	};
> +};
> +
> +&pmi8998_wled {
> +	status = "disabled";
> +};

It's already disabled

> +
> +&qupv3_id_0 {
> +	status = "okay";
> +};
> +
> +&qupv3_id_1 {
> +	status = "okay";
> +};
> +
> +&sdhc_2 {
> +	status = "okay";

last, please (there's more occurences below)


> +	pcie0_default_state: pcie0-default-state {
> +		clkreq-pins {
> +			pins = "gpio36";
> +			function = "pci_e0";
> +			bias-pull-up;
> +		};
> +
> +		perst-n-pins {
> +			pins = "gpio35";
> +			function = "gpio";
> +			drive-strength = <2>;
> +			bias-pull-down;

bias-disable?

Konrad