Documentation/devicetree/bindings/arm/qcom.yaml | 6 + arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/purwa-iot-evk.dts | 1549 +++++++++++++++++++++++ arch/arm64/boot/dts/qcom/purwa-iot-som.dtsi | 685 ++++++++++ drivers/firmware/qcom/qcom_scm.c | 1 + 5 files changed, 2242 insertions(+)
From: Yijie Yang <yijie.yang@oss.qualcomm.com>
Introduce the device tree, DT bindings, and driver updates required to enable
the bring-up of the PURWA-IOT-EVK evaluation board. Focus is on two key
hardware components:
PURWA-IOT-SOM — A compact System-on-Module integrating the SoC, GPIOs, and
PMICs. Designed for modularity, it can pair with various carrier boards to
support diverse use cases.
PURWA-IOT-EVK — A carrier board tailored for IoT scenarios, providing
essential peripherals such as UART, on-board PMICs, and USB components.
Together, these components form a flexible and scalable platform. Initial
functionality is achieved through proper device tree configuration and driver
support.
The PURWA-IOT-EVK/SOM shares most of its hardware design with
HAMOA-IOT-EVK/SOM, differing primarily in the BOM. Consequently, the DTS files
are largely similar. Both platforms belong to Qualcomm’s IQ-X family. For more
details on the IQ-X series, see:
https://www.qualcomm.com/internet-of-things/products/iq-x-series
Hardware differences between HAMOA-IOT and PURWA-IOT:
- Display — PURWA uses a different number of clocks and frequency compared to
HAMOA.
- GPU — PURWA integrates a different GPU.
- USB0 — PURWA uses a PS8833 retimer, while HAMOA employs an FSUSB42 as the
SBU switch.
Features added and enabled:
- UART
- On-board regulators
- Regulators on the SOM
- PMIC GLINK
- USB0 through USB6 and their PHYs
- Embedded USB (eUSB) repeaters
- USB Type-C mux
- PCIe3, PCIe4, PCIe5, PCIe6a
- Reserved memory regions
- Pinctrl
- NVMe
- ADSP, CDSP
- WLAN, Bluetooth (M.2 interface)
- USB DisplayPort and eDP
- Graphics
- Audio
- TPM
Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com>
---
Changes in v2:
- Update the GPU firmware path.
- Update the description in the cover letter.
- Reorder the patches.
- Use separate DTS files for Purwa and Hamoa.
- Update base commit.
- Link to v1: https://lore.kernel.org/all/20251222-purwa-v1-0-14ab9316e5ff@oss.qualcomm.com/
Changes in v3:
- Delete unused PMIC and thermal nodes.
- Add WiFi node.
- Add display backlight node.
- Add connectors and VBUS regulators for USB3 and USB6.
- Enable PCIe3 and PCIe5; add PCIe ports along with reset and wake-up GPIOs.
- Link to v2: https://lore.kernel.org/r/20260109-purwa-v2-0-f39ee10684cb@oss.qualcomm.com
Changes in v4:
- Enable TPM.
- Update the descriptions for video and the USB OF graph.
- Link to v3: https://lore.kernel.org/all/20260113-purwa-v3-0-16eefacbdce9@oss.qualcomm.com/
Changes in v5:
- Reorder nodes in purwa-iot-evk.dts.
- Update base commit.
- The DT binding change that fixes the DT warning for pcie3_phy is located at: https://lore.kernel.org/linux-arm-msm/20260119-topic-purwa_phy_shutup_warning-v1-1-997a692b31c6@oss.qualcomm.com/T/#u
- Link to v4: https://lore.kernel.org/r/20260116-purwa-v4-0-89b2adae9f09@oss.qualcomm.com
---
Yijie Yang (4):
dt-bindings: arm: qcom: Document PURWA-IOT-EVK board
firmware: qcom: scm: Allow QSEECOM on PURWA-IOT-EVK
arm64: dts: qcom: Add PURWA-IOT-SOM platform
arm64: dts: qcom: Add base PURWA-IOT-EVK board
Documentation/devicetree/bindings/arm/qcom.yaml | 6 +
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/purwa-iot-evk.dts | 1549 +++++++++++++++++++++++
arch/arm64/boot/dts/qcom/purwa-iot-som.dtsi | 685 ++++++++++
drivers/firmware/qcom/qcom_scm.c | 1 +
5 files changed, 2242 insertions(+)
---
base-commit: 6267b2da1b2d04847a1a8f441e138bc4a89435ee
change-id: 20251113-purwa-907ec75b4959
Best regards,
--
Yijie Yang <yijie.yang@oss.qualcomm.com>
On Mon, 02 Feb 2026 15:35:44 +0800, YijieYang wrote: > From: Yijie Yang <yijie.yang@oss.qualcomm.com> > > Introduce the device tree, DT bindings, and driver updates required to enable > the bring-up of the PURWA-IOT-EVK evaluation board. Focus is on two key > hardware components: > > PURWA-IOT-SOM — A compact System-on-Module integrating the SoC, GPIOs, and > PMICs. Designed for modularity, it can pair with various carrier boards to > support diverse use cases. > > PURWA-IOT-EVK — A carrier board tailored for IoT scenarios, providing > essential peripherals such as UART, on-board PMICs, and USB components. > > Together, these components form a flexible and scalable platform. Initial > functionality is achieved through proper device tree configuration and driver > support. > > The PURWA-IOT-EVK/SOM shares most of its hardware design with > HAMOA-IOT-EVK/SOM, differing primarily in the BOM. Consequently, the DTS files > are largely similar. Both platforms belong to Qualcomm’s IQ-X family. For more > details on the IQ-X series, see: > https://www.qualcomm.com/internet-of-things/products/iq-x-series > > Hardware differences between HAMOA-IOT and PURWA-IOT: > - Display — PURWA uses a different number of clocks and frequency compared to > HAMOA. > - GPU — PURWA integrates a different GPU. > - USB0 — PURWA uses a PS8833 retimer, while HAMOA employs an FSUSB42 as the > SBU switch. > > Features added and enabled: > - UART > - On-board regulators > - Regulators on the SOM > - PMIC GLINK > - USB0 through USB6 and their PHYs > - Embedded USB (eUSB) repeaters > - USB Type-C mux > - PCIe3, PCIe4, PCIe5, PCIe6a > - Reserved memory regions > - Pinctrl > - NVMe > - ADSP, CDSP > - WLAN, Bluetooth (M.2 interface) > - USB DisplayPort and eDP > - Graphics > - Audio > - TPM > > Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com> > --- > Changes in v2: > - Update the GPU firmware path. > - Update the description in the cover letter. > - Reorder the patches. > - Use separate DTS files for Purwa and Hamoa. > - Update base commit. > - Link to v1: https://lore.kernel.org/all/20251222-purwa-v1-0-14ab9316e5ff@oss.qualcomm.com/ > > Changes in v3: > - Delete unused PMIC and thermal nodes. > - Add WiFi node. > - Add display backlight node. > - Add connectors and VBUS regulators for USB3 and USB6. > - Enable PCIe3 and PCIe5; add PCIe ports along with reset and wake-up GPIOs. > - Link to v2: https://lore.kernel.org/r/20260109-purwa-v2-0-f39ee10684cb@oss.qualcomm.com > > Changes in v4: > - Enable TPM. > - Update the descriptions for video and the USB OF graph. > - Link to v3: https://lore.kernel.org/all/20260113-purwa-v3-0-16eefacbdce9@oss.qualcomm.com/ > > Changes in v5: > - Reorder nodes in purwa-iot-evk.dts. > - Update base commit. > - The DT binding change that fixes the DT warning for pcie3_phy is located at: https://lore.kernel.org/linux-arm-msm/20260119-topic-purwa_phy_shutup_warning-v1-1-997a692b31c6@oss.qualcomm.com/T/#u > - Link to v4: https://lore.kernel.org/r/20260116-purwa-v4-0-89b2adae9f09@oss.qualcomm.com > > --- > Yijie Yang (4): > dt-bindings: arm: qcom: Document PURWA-IOT-EVK board > firmware: qcom: scm: Allow QSEECOM on PURWA-IOT-EVK > arm64: dts: qcom: Add PURWA-IOT-SOM platform > arm64: dts: qcom: Add base PURWA-IOT-EVK board > > Documentation/devicetree/bindings/arm/qcom.yaml | 6 + > arch/arm64/boot/dts/qcom/Makefile | 1 + > arch/arm64/boot/dts/qcom/purwa-iot-evk.dts | 1549 +++++++++++++++++++++++ > arch/arm64/boot/dts/qcom/purwa-iot-som.dtsi | 685 ++++++++++ > drivers/firmware/qcom/qcom_scm.c | 1 + > 5 files changed, 2242 insertions(+) > --- > base-commit: 6267b2da1b2d04847a1a8f441e138bc4a89435ee > change-id: 20251113-purwa-907ec75b4959 > > Best regards, > -- > Yijie Yang <yijie.yang@oss.qualcomm.com> > > > My bot found DTB warnings on the .dts/.dtsi files added or changed in this series. Some warnings may be existing warnings. Consider fixing existing warnings before adding new features. Perhaps the warnings are fixed by another series. If that is the case, please set the base commit and any dependencies for the series using "b4". Ultimately, it is up to the platform maintainer whether these warnings are acceptable or not. If you already ran DT checks and didn't see these error(s), then make sure dt-schema is up to date: pip3 install dtschema --upgrade This patch series was applied (using b4) to base: Base: 6267b2da1b2d04847a1a8f441e138bc4a89435ee (use --merge-base to override) If this is not the correct base, please add 'base-commit' tag (or use b4 which does this automatically) New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/qcom/' for 20260202-purwa-v5-0-1f5a93578802@oss.qualcomm.com: arch/arm64/boot/dts/qcom/purwa-iot-evk.dtb: phy@1bd4000 (qcom,x1p42100-qmp-gen4x4-pcie-phy): 'qcom,4ln-config-sel' is a required property from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
On 2/4/2026 1:37 AM, Rob Herring wrote: > > On Mon, 02 Feb 2026 15:35:44 +0800, YijieYang wrote: >> From: Yijie Yang <yijie.yang@oss.qualcomm.com> >> >> Introduce the device tree, DT bindings, and driver updates required to enable >> the bring-up of the PURWA-IOT-EVK evaluation board. Focus is on two key >> hardware components: >> >> PURWA-IOT-SOM — A compact System-on-Module integrating the SoC, GPIOs, and >> PMICs. Designed for modularity, it can pair with various carrier boards to >> support diverse use cases. >> >> PURWA-IOT-EVK — A carrier board tailored for IoT scenarios, providing >> essential peripherals such as UART, on-board PMICs, and USB components. >> >> Together, these components form a flexible and scalable platform. Initial >> functionality is achieved through proper device tree configuration and driver >> support. >> >> The PURWA-IOT-EVK/SOM shares most of its hardware design with >> HAMOA-IOT-EVK/SOM, differing primarily in the BOM. Consequently, the DTS files >> are largely similar. Both platforms belong to Qualcomm’s IQ-X family. For more >> details on the IQ-X series, see: >> https://www.qualcomm.com/internet-of-things/products/iq-x-series >> >> Hardware differences between HAMOA-IOT and PURWA-IOT: >> - Display — PURWA uses a different number of clocks and frequency compared to >> HAMOA. >> - GPU — PURWA integrates a different GPU. >> - USB0 — PURWA uses a PS8833 retimer, while HAMOA employs an FSUSB42 as the >> SBU switch. >> >> Features added and enabled: >> - UART >> - On-board regulators >> - Regulators on the SOM >> - PMIC GLINK >> - USB0 through USB6 and their PHYs >> - Embedded USB (eUSB) repeaters >> - USB Type-C mux >> - PCIe3, PCIe4, PCIe5, PCIe6a >> - Reserved memory regions >> - Pinctrl >> - NVMe >> - ADSP, CDSP >> - WLAN, Bluetooth (M.2 interface) >> - USB DisplayPort and eDP >> - Graphics >> - Audio >> - TPM >> >> Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com> >> --- >> Changes in v2: >> - Update the GPU firmware path. >> - Update the description in the cover letter. >> - Reorder the patches. >> - Use separate DTS files for Purwa and Hamoa. >> - Update base commit. >> - Link to v1: https://lore.kernel.org/all/20251222-purwa-v1-0-14ab9316e5ff@oss.qualcomm.com/ >> >> Changes in v3: >> - Delete unused PMIC and thermal nodes. >> - Add WiFi node. >> - Add display backlight node. >> - Add connectors and VBUS regulators for USB3 and USB6. >> - Enable PCIe3 and PCIe5; add PCIe ports along with reset and wake-up GPIOs. >> - Link to v2: https://lore.kernel.org/r/20260109-purwa-v2-0-f39ee10684cb@oss.qualcomm.com >> >> Changes in v4: >> - Enable TPM. >> - Update the descriptions for video and the USB OF graph. >> - Link to v3: https://lore.kernel.org/all/20260113-purwa-v3-0-16eefacbdce9@oss.qualcomm.com/ >> >> Changes in v5: >> - Reorder nodes in purwa-iot-evk.dts. >> - Update base commit. >> - The DT binding change that fixes the DT warning for pcie3_phy is located at: https://lore.kernel.org/linux-arm-msm/20260119-topic-purwa_phy_shutup_warning-v1-1-997a692b31c6@oss.qualcomm.com/T/#u >> - Link to v4: https://lore.kernel.org/r/20260116-purwa-v4-0-89b2adae9f09@oss.qualcomm.com >> >> --- >> Yijie Yang (4): >> dt-bindings: arm: qcom: Document PURWA-IOT-EVK board >> firmware: qcom: scm: Allow QSEECOM on PURWA-IOT-EVK >> arm64: dts: qcom: Add PURWA-IOT-SOM platform >> arm64: dts: qcom: Add base PURWA-IOT-EVK board >> >> Documentation/devicetree/bindings/arm/qcom.yaml | 6 + >> arch/arm64/boot/dts/qcom/Makefile | 1 + >> arch/arm64/boot/dts/qcom/purwa-iot-evk.dts | 1549 +++++++++++++++++++++++ >> arch/arm64/boot/dts/qcom/purwa-iot-som.dtsi | 685 ++++++++++ >> drivers/firmware/qcom/qcom_scm.c | 1 + >> 5 files changed, 2242 insertions(+) >> --- >> base-commit: 6267b2da1b2d04847a1a8f441e138bc4a89435ee >> change-id: 20251113-purwa-907ec75b4959 >> >> Best regards, >> -- >> Yijie Yang <yijie.yang@oss.qualcomm.com> >> >> >> > > > My bot found DTB warnings on the .dts/.dtsi files added or changed in > this series. > > Some warnings may be existing warnings. Consider fixing existing > warnings before adding new features. > > Perhaps the warnings are fixed by another series. If that is the case, > please set the base commit and any dependencies for the series using > "b4". > > Ultimately, it is up to the platform maintainer whether these warnings > are acceptable or not. > > If you already ran DT checks and didn't see these error(s), then > make sure dt-schema is up to date: > > pip3 install dtschema --upgrade > > > This patch series was applied (using b4) to base: > Base: 6267b2da1b2d04847a1a8f441e138bc4a89435ee (use --merge-base to override) > > If this is not the correct base, please add 'base-commit' tag > (or use b4 which does this automatically) > > > New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/qcom/' for 20260202-purwa-v5-0-1f5a93578802@oss.qualcomm.com: > > arch/arm64/boot/dts/qcom/purwa-iot-evk.dtb: phy@1bd4000 (qcom,x1p42100-qmp-gen4x4-pcie-phy): 'qcom,4ln-config-sel' is a required property > from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-pcie-phy.yaml > I have already listed the fix in the cover letter: https://lore.kernel.org/linux-arm-msm/20260119-topic-purwa_phy_shutup_warning-v1-1-997a692b31c6@oss.qualcomm.com/T/#u It is not recommended to list it as a dependency in the latest version. > > > -- Best Regards, Yijie
On Wed, Feb 04, 2026 at 09:42:04AM +0800, Yijie Yang wrote: > > > On 2/4/2026 1:37 AM, Rob Herring wrote: > > > > On Mon, 02 Feb 2026 15:35:44 +0800, YijieYang wrote: > > > From: Yijie Yang <yijie.yang@oss.qualcomm.com> > > > > > > Introduce the device tree, DT bindings, and driver updates required to enable > > > the bring-up of the PURWA-IOT-EVK evaluation board. Focus is on two key > > > hardware components: > > > > > > PURWA-IOT-SOM — A compact System-on-Module integrating the SoC, GPIOs, and > > > PMICs. Designed for modularity, it can pair with various carrier boards to > > > support diverse use cases. > > > > > > PURWA-IOT-EVK — A carrier board tailored for IoT scenarios, providing > > > essential peripherals such as UART, on-board PMICs, and USB components. > > > > > > Together, these components form a flexible and scalable platform. Initial > > > functionality is achieved through proper device tree configuration and driver > > > support. > > > > > > The PURWA-IOT-EVK/SOM shares most of its hardware design with > > > HAMOA-IOT-EVK/SOM, differing primarily in the BOM. Consequently, the DTS files > > > are largely similar. Both platforms belong to Qualcomm’s IQ-X family. For more > > > details on the IQ-X series, see: > > > https://www.qualcomm.com/internet-of-things/products/iq-x-series > > > > > > Hardware differences between HAMOA-IOT and PURWA-IOT: > > > - Display — PURWA uses a different number of clocks and frequency compared to > > > HAMOA. > > > - GPU — PURWA integrates a different GPU. > > > - USB0 — PURWA uses a PS8833 retimer, while HAMOA employs an FSUSB42 as the > > > SBU switch. > > > > > > Features added and enabled: > > > - UART > > > - On-board regulators > > > - Regulators on the SOM > > > - PMIC GLINK > > > - USB0 through USB6 and their PHYs > > > - Embedded USB (eUSB) repeaters > > > - USB Type-C mux > > > - PCIe3, PCIe4, PCIe5, PCIe6a > > > - Reserved memory regions > > > - Pinctrl > > > - NVMe > > > - ADSP, CDSP > > > - WLAN, Bluetooth (M.2 interface) > > > - USB DisplayPort and eDP > > > - Graphics > > > - Audio > > > - TPM > > > > > > Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com> > > > --- > > > Changes in v2: > > > - Update the GPU firmware path. > > > - Update the description in the cover letter. > > > - Reorder the patches. > > > - Use separate DTS files for Purwa and Hamoa. > > > - Update base commit. > > > - Link to v1: https://lore.kernel.org/all/20251222-purwa-v1-0-14ab9316e5ff@oss.qualcomm.com/ > > > > > > Changes in v3: > > > - Delete unused PMIC and thermal nodes. > > > - Add WiFi node. > > > - Add display backlight node. > > > - Add connectors and VBUS regulators for USB3 and USB6. > > > - Enable PCIe3 and PCIe5; add PCIe ports along with reset and wake-up GPIOs. > > > - Link to v2: https://lore.kernel.org/r/20260109-purwa-v2-0-f39ee10684cb@oss.qualcomm.com > > > > > > Changes in v4: > > > - Enable TPM. > > > - Update the descriptions for video and the USB OF graph. > > > - Link to v3: https://lore.kernel.org/all/20260113-purwa-v3-0-16eefacbdce9@oss.qualcomm.com/ > > > > > > Changes in v5: > > > - Reorder nodes in purwa-iot-evk.dts. > > > - Update base commit. > > > - The DT binding change that fixes the DT warning for pcie3_phy is located at: https://lore.kernel.org/linux-arm-msm/20260119-topic-purwa_phy_shutup_warning-v1-1-997a692b31c6@oss.qualcomm.com/T/#u > > > - Link to v4: https://lore.kernel.org/r/20260116-purwa-v4-0-89b2adae9f09@oss.qualcomm.com > > > > > > --- > > > Yijie Yang (4): > > > dt-bindings: arm: qcom: Document PURWA-IOT-EVK board > > > firmware: qcom: scm: Allow QSEECOM on PURWA-IOT-EVK > > > arm64: dts: qcom: Add PURWA-IOT-SOM platform > > > arm64: dts: qcom: Add base PURWA-IOT-EVK board > > > > > > Documentation/devicetree/bindings/arm/qcom.yaml | 6 + > > > arch/arm64/boot/dts/qcom/Makefile | 1 + > > > arch/arm64/boot/dts/qcom/purwa-iot-evk.dts | 1549 +++++++++++++++++++++++ > > > arch/arm64/boot/dts/qcom/purwa-iot-som.dtsi | 685 ++++++++++ > > > drivers/firmware/qcom/qcom_scm.c | 1 + > > > 5 files changed, 2242 insertions(+) > > > --- > > > base-commit: 6267b2da1b2d04847a1a8f441e138bc4a89435ee > > > change-id: 20251113-purwa-907ec75b4959 > > > > > > Best regards, > > > -- > > > Yijie Yang <yijie.yang@oss.qualcomm.com> > > > > > > > > > > > > > > > My bot found DTB warnings on the .dts/.dtsi files added or changed in > > this series. > > > > Some warnings may be existing warnings. Consider fixing existing > > warnings before adding new features. > > > > Perhaps the warnings are fixed by another series. If that is the case, > > please set the base commit and any dependencies for the series using > > "b4". > > > > Ultimately, it is up to the platform maintainer whether these warnings > > are acceptable or not. > > > > If you already ran DT checks and didn't see these error(s), then > > make sure dt-schema is up to date: > > > > pip3 install dtschema --upgrade > > > > > > This patch series was applied (using b4) to base: > > Base: 6267b2da1b2d04847a1a8f441e138bc4a89435ee (use --merge-base to override) > > > > If this is not the correct base, please add 'base-commit' tag > > (or use b4 which does this automatically) > > > > > > New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/qcom/' for 20260202-purwa-v5-0-1f5a93578802@oss.qualcomm.com: > > > > arch/arm64/boot/dts/qcom/purwa-iot-evk.dtb: phy@1bd4000 (qcom,x1p42100-qmp-gen4x4-pcie-phy): 'qcom,4ln-config-sel' is a required property > > from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-pcie-phy.yaml > > > > I have already listed the fix in the cover letter: > https://lore.kernel.org/linux-arm-msm/20260119-topic-purwa_phy_shutup_warning-v1-1-997a692b31c6@oss.qualcomm.com/T/#u > It is not recommended to list it as a dependency in the latest version. You can use `b4 prep --edit-deps` to mark it as a dependency to be picked up by the bot. > > > > > > > > > > -- > Best Regards, > Yijie > -- With best wishes Dmitry
On 2/4/2026 10:38 AM, Dmitry Baryshkov wrote: > On Wed, Feb 04, 2026 at 09:42:04AM +0800, Yijie Yang wrote: >> >> >> On 2/4/2026 1:37 AM, Rob Herring wrote: >>> >>> On Mon, 02 Feb 2026 15:35:44 +0800, YijieYang wrote: >>>> From: Yijie Yang <yijie.yang@oss.qualcomm.com> >>>> >>>> Introduce the device tree, DT bindings, and driver updates required to enable >>>> the bring-up of the PURWA-IOT-EVK evaluation board. Focus is on two key >>>> hardware components: >>>> >>>> PURWA-IOT-SOM — A compact System-on-Module integrating the SoC, GPIOs, and >>>> PMICs. Designed for modularity, it can pair with various carrier boards to >>>> support diverse use cases. >>>> >>>> PURWA-IOT-EVK — A carrier board tailored for IoT scenarios, providing >>>> essential peripherals such as UART, on-board PMICs, and USB components. >>>> >>>> Together, these components form a flexible and scalable platform. Initial >>>> functionality is achieved through proper device tree configuration and driver >>>> support. >>>> >>>> The PURWA-IOT-EVK/SOM shares most of its hardware design with >>>> HAMOA-IOT-EVK/SOM, differing primarily in the BOM. Consequently, the DTS files >>>> are largely similar. Both platforms belong to Qualcomm’s IQ-X family. For more >>>> details on the IQ-X series, see: >>>> https://www.qualcomm.com/internet-of-things/products/iq-x-series >>>> >>>> Hardware differences between HAMOA-IOT and PURWA-IOT: >>>> - Display — PURWA uses a different number of clocks and frequency compared to >>>> HAMOA. >>>> - GPU — PURWA integrates a different GPU. >>>> - USB0 — PURWA uses a PS8833 retimer, while HAMOA employs an FSUSB42 as the >>>> SBU switch. >>>> >>>> Features added and enabled: >>>> - UART >>>> - On-board regulators >>>> - Regulators on the SOM >>>> - PMIC GLINK >>>> - USB0 through USB6 and their PHYs >>>> - Embedded USB (eUSB) repeaters >>>> - USB Type-C mux >>>> - PCIe3, PCIe4, PCIe5, PCIe6a >>>> - Reserved memory regions >>>> - Pinctrl >>>> - NVMe >>>> - ADSP, CDSP >>>> - WLAN, Bluetooth (M.2 interface) >>>> - USB DisplayPort and eDP >>>> - Graphics >>>> - Audio >>>> - TPM >>>> >>>> Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com> >>>> --- >>>> Changes in v2: >>>> - Update the GPU firmware path. >>>> - Update the description in the cover letter. >>>> - Reorder the patches. >>>> - Use separate DTS files for Purwa and Hamoa. >>>> - Update base commit. >>>> - Link to v1: https://lore.kernel.org/all/20251222-purwa-v1-0-14ab9316e5ff@oss.qualcomm.com/ >>>> >>>> Changes in v3: >>>> - Delete unused PMIC and thermal nodes. >>>> - Add WiFi node. >>>> - Add display backlight node. >>>> - Add connectors and VBUS regulators for USB3 and USB6. >>>> - Enable PCIe3 and PCIe5; add PCIe ports along with reset and wake-up GPIOs. >>>> - Link to v2: https://lore.kernel.org/r/20260109-purwa-v2-0-f39ee10684cb@oss.qualcomm.com >>>> >>>> Changes in v4: >>>> - Enable TPM. >>>> - Update the descriptions for video and the USB OF graph. >>>> - Link to v3: https://lore.kernel.org/all/20260113-purwa-v3-0-16eefacbdce9@oss.qualcomm.com/ >>>> >>>> Changes in v5: >>>> - Reorder nodes in purwa-iot-evk.dts. >>>> - Update base commit. >>>> - The DT binding change that fixes the DT warning for pcie3_phy is located at: https://lore.kernel.org/linux-arm-msm/20260119-topic-purwa_phy_shutup_warning-v1-1-997a692b31c6@oss.qualcomm.com/T/#u >>>> - Link to v4: https://lore.kernel.org/r/20260116-purwa-v4-0-89b2adae9f09@oss.qualcomm.com >>>> >>>> --- >>>> Yijie Yang (4): >>>> dt-bindings: arm: qcom: Document PURWA-IOT-EVK board >>>> firmware: qcom: scm: Allow QSEECOM on PURWA-IOT-EVK >>>> arm64: dts: qcom: Add PURWA-IOT-SOM platform >>>> arm64: dts: qcom: Add base PURWA-IOT-EVK board >>>> >>>> Documentation/devicetree/bindings/arm/qcom.yaml | 6 + >>>> arch/arm64/boot/dts/qcom/Makefile | 1 + >>>> arch/arm64/boot/dts/qcom/purwa-iot-evk.dts | 1549 +++++++++++++++++++++++ >>>> arch/arm64/boot/dts/qcom/purwa-iot-som.dtsi | 685 ++++++++++ >>>> drivers/firmware/qcom/qcom_scm.c | 1 + >>>> 5 files changed, 2242 insertions(+) >>>> --- >>>> base-commit: 6267b2da1b2d04847a1a8f441e138bc4a89435ee >>>> change-id: 20251113-purwa-907ec75b4959 >>>> >>>> Best regards, >>>> -- >>>> Yijie Yang <yijie.yang@oss.qualcomm.com> >>>> >>>> >>>> >>> >>> >>> My bot found DTB warnings on the .dts/.dtsi files added or changed in >>> this series. >>> >>> Some warnings may be existing warnings. Consider fixing existing >>> warnings before adding new features. >>> >>> Perhaps the warnings are fixed by another series. If that is the case, >>> please set the base commit and any dependencies for the series using >>> "b4". >>> >>> Ultimately, it is up to the platform maintainer whether these warnings >>> are acceptable or not. >>> >>> If you already ran DT checks and didn't see these error(s), then >>> make sure dt-schema is up to date: >>> >>> pip3 install dtschema --upgrade >>> >>> >>> This patch series was applied (using b4) to base: >>> Base: 6267b2da1b2d04847a1a8f441e138bc4a89435ee (use --merge-base to override) >>> >>> If this is not the correct base, please add 'base-commit' tag >>> (or use b4 which does this automatically) >>> >>> >>> New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/qcom/' for 20260202-purwa-v5-0-1f5a93578802@oss.qualcomm.com: >>> >>> arch/arm64/boot/dts/qcom/purwa-iot-evk.dtb: phy@1bd4000 (qcom,x1p42100-qmp-gen4x4-pcie-phy): 'qcom,4ln-config-sel' is a required property >>> from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-pcie-phy.yaml >>> >> >> I have already listed the fix in the cover letter: >> https://lore.kernel.org/linux-arm-msm/20260119-topic-purwa_phy_shutup_warning-v1-1-997a692b31c6@oss.qualcomm.com/T/#u >> It is not recommended to list it as a dependency in the latest version. > > You can use `b4 prep --edit-deps` to mark it as a dependency to be > picked up by the bot. Krzysztof mentioned in v4 that this is not a dependency and only needs to be mentioned in the changelog. > >> >> >>> >>> >>> >> >> -- >> Best Regards, >> Yijie >> > -- Best Regards, Yijie
© 2016 - 2026 Red Hat, Inc.