The SATA controllers on RK356x are identical to the ones found on RK3588,
but don't yet provide a port sub-node. Per the datasheet the RK356x also
supports the fbscp capability and has the same queue maximums.

So add port sub-nodes to both sata controllers on RK356x, and move the
phy properties to it. Also add phandles to the ports, so that boards can
add their target-supply when available.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
---
 arch/arm64/boot/dts/rockchip/rk356x-base.dtsi | 27 ++++++++++++++++---
 1 file changed, 23 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk356x-base.dtsi b/arch/arm64/boot/dts/rockchip/rk356x-base.dtsi
index b84055a77ac5..c6bd051b6a25 100644
--- a/arch/arm64/boot/dts/rockchip/rk356x-base.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk356x-base.dtsi
@@ -3,6 +3,7 @@
  * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
  */
 
+#include <dt-bindings/ata/ahci.h>
 #include <dt-bindings/clock/rk3568-cru.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/interrupt-controller/irq.h>
@@ -234,11 +235,20 @@ sata1: sata@fc400000 {
 			 <&cru CLK_SATA1_RXOOB>;
 		clock-names = "sata", "pmalive", "rxoob";
 		interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
-		phys = <&combphy1 PHY_TYPE_SATA>;
-		phy-names = "sata-phy";
 		ports-implemented = <0x1>;
 		power-domains = <&power RK3568_PD_PIPE>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 		status = "disabled";
+
+		sata1_port0: sata-port@0 {
+			reg = <0>;
+			hba-port-cap = <HBA_PORT_FBSCP>;
+			phys = <&combphy1 PHY_TYPE_SATA>;
+			phy-names = "sata-phy";
+			snps,rx-ts-max = <32>;
+			snps,tx-ts-max = <32>;
+		};
 	};
 
 	sata2: sata@fc800000 {
@@ -248,11 +258,20 @@ sata2: sata@fc800000 {
 			 <&cru CLK_SATA2_RXOOB>;
 		clock-names = "sata", "pmalive", "rxoob";
 		interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
-		phys = <&combphy2 PHY_TYPE_SATA>;
-		phy-names = "sata-phy";
 		ports-implemented = <0x1>;
 		power-domains = <&power RK3568_PD_PIPE>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 		status = "disabled";
+
+		sata2_port0: sata-port@0 {
+			reg = <0>;
+			hba-port-cap = <HBA_PORT_FBSCP>;
+			phys = <&combphy2 PHY_TYPE_SATA>;
+			phy-names = "sata-phy";
+			snps,rx-ts-max = <32>;
+			snps,tx-ts-max = <32>;
+		};
 	};
 
 	usb_host0_xhci: usb@fcc00000 {
-- 
2.47.2