Implement clk provider driver so we can disable the clock output when it
isn't needed. This helps to reduce EMF noise

Signed-off-by: Bjørn Mork <bjorn@mork.no>
---
 drivers/net/phy/air_en8811h.c | 107 ++++++++++++++++++++++++++++++++++
 1 file changed, 107 insertions(+)

diff --git a/drivers/net/phy/air_en8811h.c b/drivers/net/phy/air_en8811h.c
index 05a7023b98a9..bfd91b4aa3a7 100644
--- a/drivers/net/phy/air_en8811h.c
+++ b/drivers/net/phy/air_en8811h.c
@@ -954,6 +954,105 @@ static int en8811h_led_hw_is_supported(struct phy_device *phydev, u8 index,
 	return 0;
 };
 
+static unsigned long an8811hb_clk_recalc_rate(struct clk_hw *hw,
+					      unsigned long parent)
+{
+	struct en8811h_priv *priv = clk_hw_to_en8811h_priv(hw);
+	struct phy_device *phydev = priv->phydev;
+	u32 pbus_value;
+	int ret;
+
+	ret = air_buckpbus_reg_read(phydev, AN8811HB_HWTRAP2, &pbus_value);
+	if (ret < 0)
+		return ret;
+
+	return (pbus_value & AN8811HB_HWTRAP2_CKO) ? 50000000 : 25000000;
+}
+
+static int an8811hb_clk_enable(struct clk_hw *hw)
+{
+	struct en8811h_priv *priv = clk_hw_to_en8811h_priv(hw);
+	struct phy_device *phydev = priv->phydev;
+
+	return air_buckpbus_reg_modify(phydev, AN8811HB_CLK_DRV,
+				       AN8811HB_CLK_DRV_CKO_MASK,
+				       AN8811HB_CLK_DRV_CKO_MASK);
+}
+
+static void an8811hb_clk_disable(struct clk_hw *hw)
+{
+	struct en8811h_priv *priv = clk_hw_to_en8811h_priv(hw);
+	struct phy_device *phydev = priv->phydev;
+
+	air_buckpbus_reg_modify(phydev, AN8811HB_CLK_DRV,
+				AN8811HB_CLK_DRV_CKO_MASK, 0);
+}
+
+static int an8811hb_clk_is_enabled(struct clk_hw *hw)
+{
+	struct en8811h_priv *priv = clk_hw_to_en8811h_priv(hw);
+	struct phy_device *phydev = priv->phydev;
+	u32 pbus_value;
+	int ret;
+
+	ret = air_buckpbus_reg_read(phydev, AN8811HB_CLK_DRV, &pbus_value);
+	if (ret < 0)
+		return ret;
+
+	return (pbus_value & AN8811HB_CLK_DRV_CKO_MASK);
+}
+
+static int an8811hb_clk_save_context(struct clk_hw *hw)
+{
+	struct en8811h_priv *priv = clk_hw_to_en8811h_priv(hw);
+
+	priv->cko_is_enabled = an8811hb_clk_is_enabled(hw);
+
+	return 0;
+}
+
+static void an8811hb_clk_restore_context(struct clk_hw *hw)
+{
+	struct en8811h_priv *priv = clk_hw_to_en8811h_priv(hw);
+
+	if (!priv->cko_is_enabled)
+		an8811hb_clk_disable(hw);
+}
+
+static const struct clk_ops an8811hb_clk_ops = {
+	.recalc_rate		= an8811hb_clk_recalc_rate,
+	.enable			= an8811hb_clk_enable,
+	.disable		= an8811hb_clk_disable,
+	.is_enabled		= an8811hb_clk_is_enabled,
+	.save_context		= an8811hb_clk_save_context,
+	.restore_context	= an8811hb_clk_restore_context,
+};
+
+static int an8811hb_clk_provider_setup(struct device *dev, struct clk_hw *hw)
+{
+	struct clk_init_data init;
+	int ret;
+
+	if (!IS_ENABLED(CONFIG_COMMON_CLK))
+		return 0;
+
+	init.name = devm_kasprintf(dev, GFP_KERNEL, "%s-cko",
+				   fwnode_get_name(dev_fwnode(dev)));
+	if (!init.name)
+		return -ENOMEM;
+
+	init.ops = &an8811hb_clk_ops;
+	init.flags = 0;
+	init.num_parents = 0;
+	hw->init = &init;
+
+	ret = devm_clk_hw_register(dev, hw);
+	if (ret)
+		return ret;
+
+	return devm_of_clk_add_hw_provider(dev, of_clk_hw_simple_get, hw);
+}
+
 static unsigned long en8811h_clk_recalc_rate(struct clk_hw *hw,
 					     unsigned long parent)
 {
@@ -1095,6 +1194,12 @@ static int an8811hb_probe(struct phy_device *phydev)
 	if (ret < 0)
 		return ret;
 
+	priv->phydev = phydev;
+	/* Co-Clock Output */
+	ret = an8811hb_clk_provider_setup(&phydev->mdio.dev, &priv->hw);
+	if (ret)
+		return ret;
+
 	/* Configure led gpio pins as output */
 	ret = air_buckpbus_reg_modify(phydev, AN8811HB_GPIO_OUTPUT,
 				      AN8811HB_GPIO_OUTPUT_345,
@@ -1488,6 +1593,8 @@ static struct phy_driver en8811h_driver[] = {
 	.get_rate_matching	= en8811h_get_rate_matching,
 	.config_aneg		= en8811h_config_aneg,
 	.read_status		= en8811h_read_status,
+	.resume			= en8811h_resume,
+	.suspend		= en8811h_suspend,
 	.config_intr		= en8811h_clear_intr,
 	.handle_interrupt	= en8811h_handle_interrupt,
 	.led_hw_is_supported	= en8811h_led_hw_is_supported,
-- 
2.47.3