The CR port is a simple 16-bit data/address parallel port that is
provided for on-chip access to the control registers inside the
USB 3.0 femtoPHY. Add control register regmap and export these
registers by debugfs to help PHY's diagnostic.

Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
---
 drivers/phy/freescale/phy-fsl-imx8mq-usb.c | 19 ++++++++++++++++++-
 1 file changed, 18 insertions(+), 1 deletion(-)

diff --git a/drivers/phy/freescale/phy-fsl-imx8mq-usb.c b/drivers/phy/freescale/phy-fsl-imx8mq-usb.c
index b05d80e849a1..958d114b0c83 100644
--- a/drivers/phy/freescale/phy-fsl-imx8mq-usb.c
+++ b/drivers/phy/freescale/phy-fsl-imx8mq-usb.c
@@ -1,5 +1,5 @@
 // SPDX-License-Identifier: GPL-2.0+
-/* Copyright (c) 2017 NXP. */
+/* Copyright 2017-2026 NXP. */
 
 #include <linux/bitfield.h>
 #include <linux/clk.h>
@@ -9,6 +9,7 @@
 #include <linux/of.h>
 #include <linux/phy/phy.h>
 #include <linux/platform_device.h>
+#include <linux/regmap.h>
 #include <linux/regulator/consumer.h>
 #include <linux/usb/typec_mux.h>
 
@@ -55,6 +56,8 @@
 #define PHY_CTRL6_ALT_CLK_EN		BIT(1)
 #define PHY_CTRL6_ALT_CLK_SEL		BIT(0)
 
+#define PHY_CRCTL			0x30
+
 #define PHY_TUNE_DEFAULT		0xffffffff
 
 #define TCA_CLK_RST			0x00
@@ -118,6 +121,7 @@ struct imx8mq_usb_phy {
 	void __iomem *base;
 	struct regulator *vbus;
 	struct tca_blk *tca;
+	struct regmap *cr_regmap;
 	u32 pcs_tx_swing_full;
 	u32 pcs_tx_deemph_3p5db;
 	u32 tx_vref_tune;
@@ -685,6 +689,14 @@ static const struct of_device_id imx8mq_usb_phy_of_match[] = {
 };
 MODULE_DEVICE_TABLE(of, imx8mq_usb_phy_of_match);
 
+static const struct regmap_config imx_cr_regmap_config = {
+	.name = "cr",
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.max_register = 0x7,
+};
+
 static int imx8mq_usb_phy_probe(struct platform_device *pdev)
 {
 	struct phy_provider *phy_provider;
@@ -713,6 +725,11 @@ static int imx8mq_usb_phy_probe(struct platform_device *pdev)
 	if (IS_ERR(imx_phy->base))
 		return PTR_ERR(imx_phy->base);
 
+	imx_phy->cr_regmap = devm_regmap_init_mmio(dev, imx_phy->base + PHY_CRCTL,
+						   &imx_cr_regmap_config);
+	if (IS_ERR(imx_phy->cr_regmap))
+		return PTR_ERR(imx_phy->cr_regmap);
+
 	phy_ops = of_device_get_match_data(dev);
 	if (!phy_ops)
 		return -EINVAL;
-- 
2.34.1