From: David Heidelberg <david@ixit.cz>

Read PHY configuration from the device-tree bus-type and save it into the csiphy
structure for later use.

For C-PHY, skip clock line configuration, as there is none.

Signed-off-by: David Heidelberg <david@ixit.cz>
---
 drivers/media/platform/qcom/camss/camss-csiphy.h |  2 ++
 drivers/media/platform/qcom/camss/camss.c        | 18 +++++++++++-------
 2 files changed, 13 insertions(+), 7 deletions(-)

diff --git a/drivers/media/platform/qcom/camss/camss-csiphy.h b/drivers/media/platform/qcom/camss/camss-csiphy.h
index 2d5054819df7f..d198171700e73 100644
--- a/drivers/media/platform/qcom/camss/camss-csiphy.h
+++ b/drivers/media/platform/qcom/camss/camss-csiphy.h
@@ -28,11 +28,13 @@ struct csiphy_lane {
 
 /**
  * struct csiphy_lanes_cfg - CSIPHY lanes configuration
+ * @phy_cfg:  interface selection (C-PHY or D-PHY)
  * @num_data: number of data lanes
  * @data:     data lanes configuration
  * @clk:      clock lane configuration (only for D-PHY)
  */
 struct csiphy_lanes_cfg {
+	enum v4l2_mbus_type phy_cfg;
 	int num_data;
 	struct csiphy_lane *data;
 	struct csiphy_lane clk;
diff --git a/drivers/media/platform/qcom/camss/camss.c b/drivers/media/platform/qcom/camss/camss.c
index 00b87fd9afbd8..ea0c8cf3cd806 100644
--- a/drivers/media/platform/qcom/camss/camss.c
+++ b/drivers/media/platform/qcom/camss/camss.c
@@ -4411,11 +4411,11 @@ static int camss_parse_endpoint_node(struct device *dev,
 	if (ret)
 		return ret;
 
-	/*
-	 * Most SoCs support both D-PHY and C-PHY standards, but currently only
-	 * D-PHY is supported in the driver.
-	 */
-	if (vep.bus_type != V4L2_MBUS_CSI2_DPHY) {
+	switch (vep.bus_type) {
+	case V4L2_MBUS_CSI2_CPHY:
+	case V4L2_MBUS_CSI2_DPHY:
+		break;
+	default:
 		dev_err(dev, "Unsupported bus type %d\n", vep.bus_type);
 		return -EINVAL;
 	}
@@ -4423,9 +4423,13 @@ static int camss_parse_endpoint_node(struct device *dev,
 	csd->interface.csiphy_id = vep.base.port;
 
 	mipi_csi2 = &vep.bus.mipi_csi2;
-	lncfg->clk.pos = mipi_csi2->clock_lane;
-	lncfg->clk.pol = mipi_csi2->lane_polarities[0];
 	lncfg->num_data = mipi_csi2->num_data_lanes;
+	lncfg->phy_cfg = vep.bus_type;
+
+	if (lncfg->phy_cfg != V4L2_MBUS_CSI2_CPHY) {
+		lncfg->clk.pos = mipi_csi2->clock_lane;
+		lncfg->clk.pol = mipi_csi2->lane_polarities[0];
+	}
 
 	lncfg->data = devm_kcalloc(dev,
 				   lncfg->num_data, sizeof(*lncfg->data),

-- 
2.51.0

On 17/01/2026 15:36, David Heidelberg via B4 Relay wrote:
> +	if (lncfg->phy_cfg != V4L2_MBUS_CSI2_CPHY) {
> +		lncfg->clk.pos = mipi_csi2->clock_lane;
> +		lncfg->clk.pol = mipi_csi2->lane_polarities[0];
> +	}

Just wondering as I look at this code; is it possible to set clock_lane 
to say 0xff in DT ?

---
bod