For systems where the ID pin isn't available as gpio use the ATTACHED_STATE
register instead to control vbus.

From the datasheet:
"This is an additional method to communicate attach other
than the ID pin. These bits can be read by the application to
determine what was attached."

Use this method if id-gpios property is not set, but the connector node
has vbus-supply defined.

Signed-off-by: Jan Remmet <j.remmet@phytec.de>
---
 drivers/usb/typec/hd3ss3220.c | 27 ++++++++++++++++++---------
 1 file changed, 18 insertions(+), 9 deletions(-)

diff --git a/drivers/usb/typec/hd3ss3220.c b/drivers/usb/typec/hd3ss3220.c
index 3876f4faead679e6c04062ab2bcf2ae928913a0a..a7c54aa8635f70d6979d98c95f80d4dac277fef2 100644
--- a/drivers/usb/typec/hd3ss3220.c
+++ b/drivers/usb/typec/hd3ss3220.c
@@ -204,6 +204,20 @@ static const struct typec_operations hd3ss3220_ops = {
 	.port_type_set = hd3ss3220_port_type_set,
 };
 
+static void hd3ss3220_regulator_control(struct hd3ss3220 *hd3ss3220, bool on)
+{
+	int ret;
+
+	if (on)
+		ret = regulator_enable(hd3ss3220->vbus);
+	else
+		ret = regulator_disable(hd3ss3220->vbus);
+
+	if (ret)
+		dev_err(hd3ss3220->dev,
+			"vbus regulator %s failed: %d\n", on ? "disable" : "enable", ret);
+}
+
 static void hd3ss3220_set_role(struct hd3ss3220 *hd3ss3220)
 {
 	enum usb_role role_state = hd3ss3220_get_attached_state(hd3ss3220);
@@ -221,6 +235,9 @@ static void hd3ss3220_set_role(struct hd3ss3220 *hd3ss3220)
 		break;
 	}
 
+	if (hd3ss3220->vbus && !hd3ss3220->id_gpiod)
+		hd3ss3220_regulator_control(hd3ss3220, role_state == USB_ROLE_HOST);
+
 	hd3ss3220->role_state = role_state;
 }
 
@@ -330,18 +347,10 @@ static const struct regmap_config config = {
 static irqreturn_t hd3ss3220_id_isr(int irq, void *dev_id)
 {
 	struct hd3ss3220 *hd3ss3220 = dev_id;
-	int ret;
 	int id;
 
 	id = gpiod_get_value_cansleep(hd3ss3220->id_gpiod);
-	if (!id)
-		ret = regulator_enable(hd3ss3220->vbus);
-	else
-		ret = regulator_disable(hd3ss3220->vbus);
-
-	if (ret)
-		dev_err(hd3ss3220->dev,
-			"vbus regulator %s failed: %d\n", id ? "disable" : "enable", ret);
+	hd3ss3220_regulator_control(hd3ss3220, !id);
 
 	return IRQ_HANDLED;
 }

---
base-commit: 944aacb68baf7624ab8d277d0ebf07f025ca137c
change-id: 20260115-wip-jremmet-hd3ss3220_vbus-732f74894acc

Best regards,
-- 
Jan Remmet <j.remmet@phytec.de>

Thu, Jan 15, 2026 at 02:11:21PM +0100, Jan Remmet kirjoitti:
> For systems where the ID pin isn't available as gpio use the ATTACHED_STATE
> register instead to control vbus.
> 
> >From the datasheet:
> "This is an additional method to communicate attach other
> than the ID pin. These bits can be read by the application to
> determine what was attached."
> 
> Use this method if id-gpios property is not set, but the connector node
> has vbus-supply defined.
> 
> Signed-off-by: Jan Remmet <j.remmet@phytec.de>

Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>

> ---
>  drivers/usb/typec/hd3ss3220.c | 27 ++++++++++++++++++---------
>  1 file changed, 18 insertions(+), 9 deletions(-)
> 
> diff --git a/drivers/usb/typec/hd3ss3220.c b/drivers/usb/typec/hd3ss3220.c
> index 3876f4faead679e6c04062ab2bcf2ae928913a0a..a7c54aa8635f70d6979d98c95f80d4dac277fef2 100644
> --- a/drivers/usb/typec/hd3ss3220.c
> +++ b/drivers/usb/typec/hd3ss3220.c
> @@ -204,6 +204,20 @@ static const struct typec_operations hd3ss3220_ops = {
>  	.port_type_set = hd3ss3220_port_type_set,
>  };
>  
> +static void hd3ss3220_regulator_control(struct hd3ss3220 *hd3ss3220, bool on)
> +{
> +	int ret;
> +
> +	if (on)
> +		ret = regulator_enable(hd3ss3220->vbus);
> +	else
> +		ret = regulator_disable(hd3ss3220->vbus);
> +
> +	if (ret)
> +		dev_err(hd3ss3220->dev,
> +			"vbus regulator %s failed: %d\n", on ? "disable" : "enable", ret);
> +}
> +
>  static void hd3ss3220_set_role(struct hd3ss3220 *hd3ss3220)
>  {
>  	enum usb_role role_state = hd3ss3220_get_attached_state(hd3ss3220);
> @@ -221,6 +235,9 @@ static void hd3ss3220_set_role(struct hd3ss3220 *hd3ss3220)
>  		break;
>  	}
>  
> +	if (hd3ss3220->vbus && !hd3ss3220->id_gpiod)
> +		hd3ss3220_regulator_control(hd3ss3220, role_state == USB_ROLE_HOST);
> +
>  	hd3ss3220->role_state = role_state;
>  }
>  
> @@ -330,18 +347,10 @@ static const struct regmap_config config = {
>  static irqreturn_t hd3ss3220_id_isr(int irq, void *dev_id)
>  {
>  	struct hd3ss3220 *hd3ss3220 = dev_id;
> -	int ret;
>  	int id;
>  
>  	id = gpiod_get_value_cansleep(hd3ss3220->id_gpiod);
> -	if (!id)
> -		ret = regulator_enable(hd3ss3220->vbus);
> -	else
> -		ret = regulator_disable(hd3ss3220->vbus);
> -
> -	if (ret)
> -		dev_err(hd3ss3220->dev,
> -			"vbus regulator %s failed: %d\n", id ? "disable" : "enable", ret);
> +	hd3ss3220_regulator_control(hd3ss3220, !id);
>  
>  	return IRQ_HANDLED;
>  }
> 
> ---
> base-commit: 944aacb68baf7624ab8d277d0ebf07f025ca137c
> change-id: 20260115-wip-jremmet-hd3ss3220_vbus-732f74894acc
> 
> Best regards,
> -- 
> Jan Remmet <j.remmet@phytec.de>

-- 
heikki