Introduce the device tree support for the QCS615-based talos-evk
platform, which follows the SMARC (Smart Mobility ARChitecture)
standard. The platform is composed of two main hardware
components: the talos-evk-som and the talos-evk carrier board.
The initial device tree includes basic support for:
- CPU and memory
- UART
- GPIOs
- Regulators
- PMIC
- Early console
- AT24MAC602 EEPROM
- MCP2515 SPI to CAN
- ADV7535 DSI-to-HDMI bridge
- DisplayPort
Signed-off-by: Sudarshan Shetty <tessolveupstream@gmail.com>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/talos-evk-cb.dtsi | 56 +++
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi | 442 ++++++++++++++++++++
arch/arm64/boot/dts/qcom/talos-evk.dts | 87 ++++
4 files changed, 586 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-cb.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-som.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/talos-evk.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 5b52f9e4e5f3..282d744acd73 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -305,6 +305,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8750-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8750-qrd.dtb
+dtb-$(CONFIG_ARCH_QCOM) += talos-evk.dtb
x1e001de-devkit-el2-dtbs := x1e001de-devkit.dtb x1-el2.dtbo
dtb-$(CONFIG_ARCH_QCOM) += x1e001de-devkit.dtb x1e001de-devkit-el2.dtb
x1e78100-lenovo-thinkpad-t14s-el2-dtbs := x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtbo
diff --git a/arch/arm64/boot/dts/qcom/talos-evk-cb.dtsi b/arch/arm64/boot/dts/qcom/talos-evk-cb.dtsi
new file mode 100644
index 000000000000..81d15ee4f366
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-evk-cb.dtsi
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+
+#include "talos-evk-som.dtsi"
+
+/ {
+ model = "Qualcomm QCS615 IQ 615 EVK";
+ compatible = "qcom,talos-evk", "qcom,qcs615", "qcom,sm6150";
+ chassis-type = "embedded";
+
+ aliases {
+ mmc1 = &sdhc_2;
+ };
+
+ dp-connector {
+ compatible = "dp-connector";
+ label = "DP0";
+ type = "full-size";
+
+ hpd-gpios = <&tlmm 104 GPIO_ACTIVE_HIGH>;
+
+ port {
+ dp0_connector_in: endpoint {
+ remote-endpoint = <&mdss_dp0_out>;
+ };
+ };
+ };
+};
+
+&pon_pwrkey {
+ status = "okay";
+};
+
+&pon_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+
+ status = "okay";
+};
+
+&sdhc_2 {
+ pinctrl-0 = <&sdc2_state_on>;
+ pinctrl-1 = <&sdc2_state_off>;
+ pinctrl-names = "default", "sleep";
+
+ bus-width = <4>;
+ cd-gpios = <&tlmm 99 GPIO_ACTIVE_LOW>;
+
+ vmmc-supply = <&vreg_l10a>;
+ vqmmc-supply = <&vreg_s4a>;
+
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/talos-evk-som.dtsi b/arch/arm64/boot/dts/qcom/talos-evk-som.dtsi
new file mode 100644
index 000000000000..1acb6997156a
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-evk-som.dtsi
@@ -0,0 +1,442 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sm6150.dtsi"
+#include "pm8150.dtsi"
+/ {
+ aliases {
+ mmc0 = &sdhc_1;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ clocks {
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <32764>;
+ #clock-cells = <0>;
+ };
+
+ xo_board_clk: xo-board-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <38400000>;
+ #clock-cells = <0>;
+ };
+ };
+
+ regulator-usb2-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "USB2_VBUS";
+ gpio = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&usb2_en>;
+ pinctrl-names = "default";
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ vreg_v3p3_can: regulator-v3p3-can {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg-v3p3-can";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vreg_v5p0_can: regulator-v5p0-can {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg-v5p0-can";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pm8150-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vreg_s3a: smps3 {
+ regulator-name = "vreg_s3a";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <650000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s4a: smps4 {
+ regulator-name = "vreg_s4a";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1829000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5a: smps5 {
+ regulator-name = "vreg_s5a";
+ regulator-min-microvolt = <1896000>;
+ regulator-max-microvolt = <2040000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s6a: smps6 {
+ regulator-name = "vreg_s6a";
+ regulator-min-microvolt = <1304000>;
+ regulator-max-microvolt = <1404000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1a: ldo1 {
+ regulator-name = "vreg_l1a";
+ regulator-min-microvolt = <488000>;
+ regulator-max-microvolt = <852000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2a: ldo2 {
+ regulator-name = "vreg_l2a";
+ regulator-min-microvolt = <1650000>;
+ regulator-max-microvolt = <3100000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3a: ldo3 {
+ regulator-name = "vreg_l3a";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1248000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5a: ldo5 {
+ regulator-name = "vreg_l5a";
+ regulator-min-microvolt = <875000>;
+ regulator-max-microvolt = <975000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7a: ldo7 {
+ regulator-name = "vreg_l7a";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8a: ldo8 {
+ regulator-name = "vreg_l8a";
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10a: ldo10 {
+ regulator-name = "vreg_l10a";
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11a: ldo11 {
+ regulator-name = "vreg_l11a";
+ regulator-min-microvolt = <1232000>;
+ regulator-max-microvolt = <1260000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12a: ldo12 {
+ regulator-name = "vreg_l12a";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1890000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13a: ldo13 {
+ regulator-name = "vreg_l13a";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3230000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l15a: ldo15 {
+ regulator-name = "vreg_l15a";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l16a: ldo16 {
+ regulator-name = "vreg_l16a";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l17a: ldo17 {
+ regulator-name = "vreg_l17a";
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&i2c5 {
+ status = "okay";
+
+ eeprom@57 {
+ compatible = "atmel,24c02";
+ reg = <0x57>;
+ pagesize = <16>;
+ };
+
+ eeprom@5f {
+ compatible = "atmel,24mac602";
+ reg = <0x5f>;
+ pagesize = <16>;
+ };
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dp0 {
+ status = "okay";
+};
+
+&mdss_dp0_out {
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000>;
+ remote-endpoint = <&dp0_connector_in>;
+};
+
+&mdss_dp_phy {
+ vdda-phy-supply = <&vreg_l11a>;
+ vdda-pll-supply = <&vreg_l5a>;
+ status = "okay";
+};
+
+&mdss_dsi0 {
+ vdda-supply = <&vreg_l11a>;
+
+ status = "okay";
+};
+
+&mdss_dsi0_out {
+ remote-endpoint = <&adv7535_in>;
+ data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+ vdds-supply = <&vreg_l5a>;
+
+ status = "okay";
+};
+
+&pcie {
+ perst-gpios = <&tlmm 101 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&pcie_default_state>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie_phy {
+ vdda-phy-supply = <&vreg_l5a>;
+ vdda-pll-supply = <&vreg_l12a>;
+
+ status = "okay";
+};
+
+&pm8150_gpios {
+ usb2_en: usb2-en-state {
+ pins = "gpio10";
+ function = "normal";
+ output-enable;
+ power-source = <0>;
+ };
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/qcs615/adsp.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ firmware-name = "qcom/qcs615/cdsp.mbn";
+
+ status = "okay";
+};
+
+&sdhc_1 {
+ pinctrl-0 = <&sdc1_state_on>;
+ pinctrl-1 = <&sdc1_state_off>;
+ pinctrl-names = "default", "sleep";
+
+ bus-width = <8>;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+ vmmc-supply = <&vreg_l17a>;
+ vqmmc-supply = <&vreg_s4a>;
+
+ non-removable;
+ no-sd;
+ no-sdio;
+
+ status = "okay";
+};
+
+&spi6 {
+ status = "okay";
+
+ can@0 {
+ compatible = "microchip,mcp2515";
+ reg = <0>;
+ clock-frequency = <20000000>;
+ interrupts-extended = <&tlmm 87 IRQ_TYPE_LEVEL_LOW>;
+ spi-max-frequency = <10000000>;
+ vdd-supply = <&vreg_v3p3_can>;
+ xceiver-supply = <&vreg_v5p0_can>;
+ };
+};
+
+&tlmm {
+ pcie_default_state: pcie-default-state {
+ clkreq-pins {
+ pins = "gpio90";
+ function = "pcie_clk_req";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-pins {
+ pins = "gpio101";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ wake-pins {
+ pins = "gpio100";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&usb_1_hsphy {
+ vdd-supply = <&vreg_l5a>;
+ vdda-pll-supply = <&vreg_l12a>;
+ vdda-phy-dpdm-supply = <&vreg_l13a>;
+
+ status = "okay";
+};
+
+&usb_qmpphy {
+ vdda-phy-supply = <&vreg_l5a>;
+ vdda-pll-supply = <&vreg_l12a>;
+
+ status = "okay";
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_hsphy_2 {
+ vdd-supply = <&vreg_l5a>;
+ vdda-pll-supply = <&vreg_l12a>;
+ vdda-phy-dpdm-supply = <&vreg_l13a>;
+
+ status = "okay";
+};
+
+&usb_2 {
+ status = "okay";
+};
+
+&usb_2_dwc3 {
+ dr_mode = "host";
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 123 GPIO_ACTIVE_LOW>;
+ vcc-supply = <&vreg_l17a>;
+ vcc-max-microamp = <600000>;
+ vccq2-supply = <&vreg_s4a>;
+ vccq2-max-microamp = <600000>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l5a>;
+ vdda-pll-supply = <&vreg_l12a>;
+
+ status = "okay";
+};
+
+&venus {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/talos-evk.dts b/arch/arm64/boot/dts/qcom/talos-evk.dts
new file mode 100644
index 000000000000..a099fbafb6a2
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-evk.dts
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+
+#include "talos-evk-cb.dtsi"
+
+/ {
+ hdmi-out {
+ compatible = "hdmi-connector";
+ type = "d";
+
+ port {
+ hdmi_con_out: endpoint {
+ remote-endpoint = <&adv7535_out>;
+ };
+ };
+ };
+
+ vreg_v5p0_out: regulator-v5p0-out {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg-v5p0-out";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ /* Powered by system 20V rail (USBC_VBUS_IN) */
+ };
+
+ vreg_v3p3_out: regulator-v3p3-out {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg-v3p3-out";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vreg_v5p0_out>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vreg_v1p8_out: regulator-v1p8-out {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg-v1p8-out";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vreg_v5p0_out>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+
+ status = "okay";
+
+ bridge: bridge@3d {
+ compatible = "adi,adv7535";
+ reg = <0x3d>;
+ avdd-supply = <&vreg_v1p8_out>;
+ dvdd-supply = <&vreg_v1p8_out>;
+ pvdd-supply = <&vreg_v1p8_out>;
+ a2vdd-supply = <&vreg_v1p8_out>;
+ v3p3-supply = <&vreg_v3p3_out>;
+ interrupts-extended = <&tlmm 26 IRQ_TYPE_LEVEL_LOW>;
+ adi,dsi-lanes = <4>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ adv7535_in: endpoint {
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ adv7535_out: endpoint {
+ remote-endpoint = <&hdmi_con_out>;
+ };
+ };
+ };
+ };
+};
--
2.34.1On 11/4/25 1:51 PM, Sudarshan Shetty wrote:
> Introduce the device tree support for the QCS615-based talos-evk
> platform, which follows the SMARC (Smart Mobility ARChitecture)
> standard. The platform is composed of two main hardware
> components: the talos-evk-som and the talos-evk carrier board.
How is the carrier board a separate entity from the "talos-evk.dts"?
[...]
> +&mdss_dp_phy {
> + vdda-phy-supply = <&vreg_l11a>;
> + vdda-pll-supply = <&vreg_l5a>;
> + status = "okay";
Please apply a consistent \n before status
[...]
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + adv7535_in: endpoint {
and between the last property and the following subnode
Konrad
> + remote-endpoint = <&mdss_dsi0_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + adv7535_out: endpoint {
> + remote-endpoint = <&hdmi_con_out>;
> + };
> + };
> + };
> + };
> +};
On 04/11/25 19:57, Konrad Dybcio wrote:
> On 11/4/25 1:51 PM, Sudarshan Shetty wrote:
>> Introduce the device tree support for the QCS615-based talos-evk
>> platform, which follows the SMARC (Smart Mobility ARChitecture)
>> standard. The platform is composed of two main hardware
>> components: the talos-evk-som and the talos-evk carrier board.
>
> How is the carrier board a separate entity from the "talos-evk.dts"?
The talos-evk platform follows a modular SoM + carrier design.
In our current implementation:
talos-evk-som.dtsi — describes SoM-specific components.
talos-evk-cb.dtsi — represents the carrier board and includes the
SoM file, adding carrier-specific interfaces (micro SD, power button etc.).
talos-evk.dts — includes both the SoM and CB DTSIs and enables HDMI
display configuration.
talos-evk-lvds.dts — also includes both the SoM and CB DTSIs but enables
LVDS instead of HDMI.
HDMI and LVDS share the same DSI output and cannot be used simultaneously.
Therefore, we provide separate top-level DTS files (talos-evk.dts for HDMI
and talos-evk-lvds.dts for LVDS), while keeping common board
logic in talos-evk-cb.dtsi.
Hence, layer looks as below:
talos-evk-som.dtsi
├── talos-evk-cb.dtsi (includes som)
│ ├── talos-evk.dts (HDMI)
│ └── talos-evk-lvds.dts (LVDS)
This ensures modularity, and properly models mutually exclusive display
configurations.
>
> [...]
>
>> +&mdss_dp_phy {
>> + vdda-phy-supply = <&vreg_l11a>;
>> + vdda-pll-supply = <&vreg_l5a>;
>> + status = "okay";
>
> Please apply a consistent \n before status
okay, will update in v6 patch.
>
> [...]
>
>> + ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + port@0 {
>> + reg = <0>;
>> + adv7535_in: endpoint {
>
> and between the last property and the following subnode
>
okay, will update in v6 patch.
> Konrad
>
>> + remote-endpoint = <&mdss_dsi0_out>;
>> + };
>> + };
>> +
>> + port@1 {
>> + reg = <1>;
>> + adv7535_out: endpoint {
>> + remote-endpoint = <&hdmi_con_out>;
>> + };
>> + };
>> + };
>> + };
>> +};
On 11/5/25 11:01 AM, Tessolve Upstream wrote: > > > On 04/11/25 19:57, Konrad Dybcio wrote: >> On 11/4/25 1:51 PM, Sudarshan Shetty wrote: >>> Introduce the device tree support for the QCS615-based talos-evk >>> platform, which follows the SMARC (Smart Mobility ARChitecture) >>> standard. The platform is composed of two main hardware >>> components: the talos-evk-som and the talos-evk carrier board. >> >> How is the carrier board a separate entity from the "talos-evk.dts"? > > The talos-evk platform follows a modular SoM + carrier design. > In our current implementation: > talos-evk-som.dtsi — describes SoM-specific components. > talos-evk-cb.dtsi — represents the carrier board and includes the > SoM file, adding carrier-specific interfaces (micro SD, power button etc.). > talos-evk.dts — includes both the SoM and CB DTSIs and enables HDMI > display configuration. > talos-evk-lvds.dts — also includes both the SoM and CB DTSIs but enables > LVDS instead of HDMI. > > HDMI and LVDS share the same DSI output and cannot be used simultaneously. > Therefore, we provide separate top-level DTS files (talos-evk.dts for HDMI > and talos-evk-lvds.dts for LVDS), while keeping common board > logic in talos-evk-cb.dtsi. > > Hence, layer looks as below: > > talos-evk-som.dtsi > ├── talos-evk-cb.dtsi (includes som) > │ ├── talos-evk.dts (HDMI) > │ └── talos-evk-lvds.dts (LVDS) > > This ensures modularity, and properly models mutually exclusive display > configurations. And are both the LVDS display and HDMI converter on separate add-in boards? Konrad
On 05/11/25 16:39, Konrad Dybcio wrote: > On 11/5/25 11:01 AM, Tessolve Upstream wrote: >> >> >> On 04/11/25 19:57, Konrad Dybcio wrote: >>> On 11/4/25 1:51 PM, Sudarshan Shetty wrote: >>>> Introduce the device tree support for the QCS615-based talos-evk >>>> platform, which follows the SMARC (Smart Mobility ARChitecture) >>>> standard. The platform is composed of two main hardware >>>> components: the talos-evk-som and the talos-evk carrier board. >>> >>> How is the carrier board a separate entity from the "talos-evk.dts"? >> >> The talos-evk platform follows a modular SoM + carrier design. >> In our current implementation: >> talos-evk-som.dtsi — describes SoM-specific components. >> talos-evk-cb.dtsi — represents the carrier board and includes the >> SoM file, adding carrier-specific interfaces (micro SD, power button etc.). >> talos-evk.dts — includes both the SoM and CB DTSIs and enables HDMI >> display configuration. >> talos-evk-lvds.dts — also includes both the SoM and CB DTSIs but enables >> LVDS instead of HDMI. >> >> HDMI and LVDS share the same DSI output and cannot be used simultaneously. >> Therefore, we provide separate top-level DTS files (talos-evk.dts for HDMI >> and talos-evk-lvds.dts for LVDS), while keeping common board >> logic in talos-evk-cb.dtsi. >> >> Hence, layer looks as below: >> >> talos-evk-som.dtsi >> ├── talos-evk-cb.dtsi (includes som) >> │ ├── talos-evk.dts (HDMI) >> │ └── talos-evk-lvds.dts (LVDS) >> >> This ensures modularity, and properly models mutually exclusive display >> configurations. > > And are both the LVDS display and HDMI converter on separate add-in boards? > Both HDMI and LVDS interfaces are present on the same carrier board, but they share the same DSI output from the SoM. The hardware requires physical reconfiguration (resistor changes) to select either the ADV7535 HDMI path or the LVDS bridge path. Because they cannot be used simultaneously and represent different hardware configurations, we provide two separate DTS files — one for HDMI and one for LVDS — while keeping the common carrier definitions in talos-evk-cb.dtsi. > Konrad
© 2016 - 2025 Red Hat, Inc.