The CANUART pins of mcu_mcan0, mcu_mcan1, mcu_uart0 and wkup_uart0 are
powered during Partial-IO and I/O Only + DDR and are capable of waking
up the system in these states. Specify the states in which these units
can do a wakeup on this board.

Note that the UARTs are not capable of wakeup in Partial-IO because of
of a UART mux on the board not being powered during Partial-IO.

Add pincontrol definitions for mcu_mcan0 and mcu_mcan1 for wakeup from
Partial-IO. Add these as wakeup pinctrl entries for both devices.

Signed-off-by: Markus Schneider-Pargmann (TI.com) <msp@baylibre.com>
---
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 71 +++++++++++++++++++++++++++++++++
 1 file changed, 71 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
index af591fe6ae4f0a91991d2904a9a61905a0eeb614..8525aa5ab812c51e2d3371b39baa5e936e616158 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
@@ -233,6 +233,10 @@ AM62AX_MCU_IOPAD(0x0030, PIN_OUTPUT, 0) /* (C8) WKUP_UART0_RTSn */
 &wkup_uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&wkup_uart0_pins_default>;
+	wakeup-source = <&system_io_ddr>,
+			<&system_deep_sleep>,
+			<&system_mcu_only>,
+			<&system_standby>;
 	status = "reserved";
 };
 
@@ -426,6 +430,42 @@ pmic_irq_pins_default: pmic-irq-default-pins {
 			AM62AX_MCU_IOPAD(0x000, PIN_INPUT, 7) /* (E11) MCU_GPIO0_0 */
 		>;
 	};
+
+	mcu_mcan0_tx_pins_default: mcu-mcan0-tx-default-pins {
+		pinctrl-single,pins = <
+			AM62AX_MCU_IOPAD(0x034, PIN_OUTPUT, 0) /* (D6) MCU_MCAN0_TX */
+		>;
+	};
+
+	mcu_mcan0_rx_pins_default: mcu-mcan0-rx-default-pins {
+		pinctrl-single,pins = <
+			AM62AX_MCU_IOPAD(0x038, PIN_INPUT, 0) /* (B3) MCU_MCAN0_RX */
+		>;
+	};
+
+	mcu_mcan0_rx_pins_wakeup: mcu-mcan0-rx-wakeup-pins {
+		pinctrl-single,pins = <
+			AM62AX_MCU_IOPAD(0x038, PIN_INPUT | PIN_WKUP_EN, 0) /* (B3) MCU_MCAN0_RX */
+		>;
+	};
+
+	mcu_mcan1_tx_pins_default: mcu-mcan1-tx-default-pins {
+		pinctrl-single,pins = <
+			AM62AX_MCU_IOPAD(0x03c, PIN_OUTPUT, 0) /* (E5) MCU_MCAN1_TX */
+		>;
+	};
+
+	mcu_mcan1_rx_pins_default: mcu-mcan1-rx-default-pins {
+		pinctrl-single,pins = <
+			AM62AX_MCU_IOPAD(0x040, PIN_INPUT, 0) /* (D4) MCU_MCAN1_RX */
+		>;
+	};
+
+	mcu_mcan1_rx_pins_wakeup: mcu-mcan1-rx-wakeup-pins {
+		pinctrl-single,pins = <
+			AM62AX_MCU_IOPAD(0x040, PIN_INPUT | PIN_WKUP_EN, 0) /* (D4) MCU_MCAN1_RX */
+		>;
+	};
 };
 
 &mcu_gpio0 {
@@ -852,4 +892,35 @@ AM62AX_IOPAD(0x008, PIN_INPUT, 0) /* (J24) OSPI0_DQS */
 	};
 };
 
+&mcu_mcan0 {
+	pinctrl-names = "default", "wakeup";
+	pinctrl-0 = <&mcu_mcan0_tx_pins_default>, <&mcu_mcan0_rx_pins_default>;
+	pinctrl-1 = <&mcu_mcan0_tx_pins_default>, <&mcu_mcan0_rx_pins_wakeup>;
+	wakeup-source = <&system_partial_io>,
+			<&system_io_ddr>,
+			<&system_deep_sleep>,
+			<&system_mcu_only>,
+			<&system_standby>;
+	status = "okay";
+};
+
+&mcu_mcan1 {
+	pinctrl-names = "default", "wakeup";
+	pinctrl-0 = <&mcu_mcan1_tx_pins_default>, <&mcu_mcan1_rx_pins_default>;
+	pinctrl-1 = <&mcu_mcan1_tx_pins_default>, <&mcu_mcan1_rx_pins_wakeup>;
+	wakeup-source = <&system_partial_io>,
+			<&system_io_ddr>,
+			<&system_deep_sleep>,
+			<&system_mcu_only>,
+			<&system_standby>;
+	status = "okay";
+};
+
+&mcu_uart0 {
+	wakeup-source = <&system_io_ddr>,
+			<&system_deep_sleep>,
+			<&system_mcu_only>,
+			<&system_standby>;
+};
+
 #include "k3-am62a-ti-ipc-firmware.dtsi"

-- 
2.51.0

Hi Markus

[...]

On 30/10/25 14:47, Markus Schneider-Pargmann (TI.com) wrote:
> +&mcu_mcan0 {
> +	pinctrl-names = "default", "wakeup";
> +	pinctrl-0 = <&mcu_mcan0_tx_pins_default>, <&mcu_mcan0_rx_pins_default>;
> +	pinctrl-1 = <&mcu_mcan0_tx_pins_default>, <&mcu_mcan0_rx_pins_wakeup>;
> +	wakeup-source = <&system_partial_io>,
> +			<&system_io_ddr>,
> +			<&system_deep_sleep>,
> +			<&system_mcu_only>,
> +			<&system_standby>;
> +	status = "okay";
> +};
> +
> +&mcu_mcan1 {
> +	pinctrl-names = "default", "wakeup";
> +	pinctrl-0 = <&mcu_mcan1_tx_pins_default>, <&mcu_mcan1_rx_pins_default>;
> +	pinctrl-1 = <&mcu_mcan1_tx_pins_default>, <&mcu_mcan1_rx_pins_wakeup>;
> +	wakeup-source = <&system_partial_io>,
> +			<&system_io_ddr>,
> +			<&system_deep_sleep>,
> +			<&system_mcu_only>,
> +			<&system_standby>;
> +	status = "okay";
> +};
> +
> +&mcu_uart0 {
> +	wakeup-source = <&system_io_ddr>,
> +			<&system_deep_sleep>,
> +			<&system_mcu_only>,
> +			<&system_standby>;
> +};
> +

MCU peripherals are under control of MCU R5 which would be running a
safety application on AM62A class of SoC. So these peripherals should
not be enabled by default here.

>  #include "k3-am62a-ti-ipc-firmware.dtsi"

-- 
Regards
Vignesh
https://ti.com/opensource

Hi Vignesh,

On Mon Nov 3, 2025 at 4:51 AM CET, Vignesh Raghavendra wrote:
> Hi Markus
>
> [...]
>
> On 30/10/25 14:47, Markus Schneider-Pargmann (TI.com) wrote:
>> +&mcu_mcan0 {
>> +	pinctrl-names = "default", "wakeup";
>> +	pinctrl-0 = <&mcu_mcan0_tx_pins_default>, <&mcu_mcan0_rx_pins_default>;
>> +	pinctrl-1 = <&mcu_mcan0_tx_pins_default>, <&mcu_mcan0_rx_pins_wakeup>;
>> +	wakeup-source = <&system_partial_io>,
>> +			<&system_io_ddr>,
>> +			<&system_deep_sleep>,
>> +			<&system_mcu_only>,
>> +			<&system_standby>;
>> +	status = "okay";
>> +};
>> +
>> +&mcu_mcan1 {
>> +	pinctrl-names = "default", "wakeup";
>> +	pinctrl-0 = <&mcu_mcan1_tx_pins_default>, <&mcu_mcan1_rx_pins_default>;
>> +	pinctrl-1 = <&mcu_mcan1_tx_pins_default>, <&mcu_mcan1_rx_pins_wakeup>;
>> +	wakeup-source = <&system_partial_io>,
>> +			<&system_io_ddr>,
>> +			<&system_deep_sleep>,
>> +			<&system_mcu_only>,
>> +			<&system_standby>;
>> +	status = "okay";
>> +};
>> +
>> +&mcu_uart0 {
>> +	wakeup-source = <&system_io_ddr>,
>> +			<&system_deep_sleep>,
>> +			<&system_mcu_only>,
>> +			<&system_standby>;
>> +};
>> +
>
> MCU peripherals are under control of MCU R5 which would be running a
> safety application on AM62A class of SoC. So these peripherals should
> not be enabled by default here.

Thanks, I will not enable them in the next version.

Best
Markus

>
>>  #include "k3-am62a-ti-ipc-firmware.dtsi"