Some Qualcomm PMICs integrate an USB Repeater device, used to
convert between eUSB2 and USB 2.0 signaling levels, reachable
in a specific address range over SPMI.

Instead of using the parent SPMI device (the main PMIC) as a kind
of syscon in this driver, register a new SPMI sub-device for EUSB2
and initialize its own regmap with this sub-device's specific base
address, retrieved from the devicetree.

This allows to stop manually adding the register base address to
every R/W call in this driver, as this can be, and is now, handled
by the regmap API instead.

Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
 drivers/phy/qualcomm/Kconfig                  |  2 +
 .../phy/qualcomm/phy-qcom-eusb2-repeater.c    | 53 ++++++++++++-------
 2 files changed, 36 insertions(+), 19 deletions(-)

diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
index 60a0ead127fa..902a788f35f1 100644
--- a/drivers/phy/qualcomm/Kconfig
+++ b/drivers/phy/qualcomm/Kconfig
@@ -128,7 +128,9 @@ config PHY_QCOM_QUSB2
 config PHY_QCOM_EUSB2_REPEATER
 	tristate "Qualcomm PMIC eUSB2 Repeater Driver"
 	depends on OF && (ARCH_QCOM || COMPILE_TEST)
+	depends on SPMI
 	select GENERIC_PHY
+	select REGMAP_SPMI
 	help
 	  Enable support for the USB high-speed eUSB2 repeater on Qualcomm
 	  PMICs. The repeater is paired with a Synopsys or M31 eUSB2 Phy
diff --git a/drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c b/drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c
index 651a12b59bc8..bdeb3c72d26a 100644
--- a/drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c
+++ b/drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c
@@ -9,6 +9,7 @@
 #include <linux/regmap.h>
 #include <linux/of.h>
 #include <linux/phy/phy.h>
+#include <linux/spmi.h>
 
 /* eUSB2 status registers */
 #define EUSB2_RPTR_STATUS		0x08
@@ -55,7 +56,6 @@ struct eusb2_repeater {
 	struct phy *phy;
 	struct regulator_bulk_data *vregs;
 	const struct eusb2_repeater_cfg *cfg;
-	u32 base;
 	enum phy_mode mode;
 };
 
@@ -118,7 +118,6 @@ static int eusb2_repeater_init(struct phy *phy)
 	struct eusb2_repeater *rptr = phy_get_drvdata(phy);
 	struct device_node *np = rptr->dev->of_node;
 	struct regmap *regmap = rptr->regmap;
-	u32 base = rptr->base;
 	u32 poll_val;
 	int ret;
 	u8 val;
@@ -127,28 +126,28 @@ static int eusb2_repeater_init(struct phy *phy)
 	if (ret)
 		return ret;
 
-	regmap_write(regmap, base + EUSB2_EN_CTL1, EUSB2_RPTR_EN);
+	regmap_write(regmap, EUSB2_EN_CTL1, EUSB2_RPTR_EN);
 
 	/* Write registers from init table */
 	for (int i = 0; i < rptr->cfg->init_tbl_num; i++)
-		regmap_write(regmap, base + rptr->cfg->init_tbl[i].reg,
+		regmap_write(regmap, rptr->cfg->init_tbl[i].reg,
 			     rptr->cfg->init_tbl[i].value);
 
 	/* Override registers from devicetree values */
 	if (!of_property_read_u8(np, "qcom,tune-usb2-preem", &val))
-		regmap_write(regmap, base + EUSB2_TUNE_USB2_PREEM, val);
+		regmap_write(regmap, EUSB2_TUNE_USB2_PREEM, val);
 
 	if (!of_property_read_u8(np, "qcom,tune-usb2-disc-thres", &val))
-		regmap_write(regmap, base + EUSB2_TUNE_HSDISC, val);
+		regmap_write(regmap, EUSB2_TUNE_HSDISC, val);
 
 	if (!of_property_read_u8(np, "qcom,tune-usb2-amplitude", &val))
-		regmap_write(regmap, base + EUSB2_TUNE_IUSB2, val);
+		regmap_write(regmap, EUSB2_TUNE_IUSB2, val);
 
 	if (!of_property_read_u8(np, "qcom,tune-res-fsdif", &val))
-		regmap_write(regmap, base + EUSB2_TUNE_RES_FSDIF, val);
+		regmap_write(regmap, EUSB2_TUNE_RES_FSDIF, val);
 
 	/* Wait for status OK */
-	ret = regmap_read_poll_timeout(regmap, base + EUSB2_RPTR_STATUS, poll_val,
+	ret = regmap_read_poll_timeout(regmap, EUSB2_RPTR_STATUS, poll_val,
 				       poll_val & RPTR_OK, 10, 5);
 	if (ret)
 		dev_err(rptr->dev, "initialization timed-out\n");
@@ -161,7 +160,6 @@ static int eusb2_repeater_set_mode(struct phy *phy,
 {
 	struct eusb2_repeater *rptr = phy_get_drvdata(phy);
 	struct regmap *regmap = rptr->regmap;
-	u32 base = rptr->base;
 
 	switch (mode) {
 	case PHY_MODE_USB_HOST:
@@ -170,8 +168,8 @@ static int eusb2_repeater_set_mode(struct phy *phy,
 		 * per eUSB 1.2 Spec. Below implement software workaround until
 		 * PHY and controller is fixing seen observation.
 		 */
-		regmap_write(regmap, base + EUSB2_FORCE_EN_5, F_CLK_19P2M_EN);
-		regmap_write(regmap, base + EUSB2_FORCE_VAL_5, V_CLK_19P2M_EN);
+		regmap_write(regmap, EUSB2_FORCE_EN_5, F_CLK_19P2M_EN);
+		regmap_write(regmap, EUSB2_FORCE_VAL_5, V_CLK_19P2M_EN);
 		break;
 	case PHY_MODE_USB_DEVICE:
 		/*
@@ -180,8 +178,8 @@ static int eusb2_repeater_set_mode(struct phy *phy,
 		 * repeater doesn't clear previous value due to shared
 		 * regulators (say host <-> device mode switch).
 		 */
-		regmap_write(regmap, base + EUSB2_FORCE_EN_5, 0);
-		regmap_write(regmap, base + EUSB2_FORCE_VAL_5, 0);
+		regmap_write(regmap, EUSB2_FORCE_EN_5, 0);
+		regmap_write(regmap, EUSB2_FORCE_VAL_5, 0);
 		break;
 	default:
 		return -EINVAL;
@@ -206,13 +204,23 @@ static const struct phy_ops eusb2_repeater_ops = {
 
 static int eusb2_repeater_probe(struct platform_device *pdev)
 {
+	struct regmap_config eusb2_regmap_config = {
+		.reg_bits = 16,
+		.val_bits = 8,
+		.max_register = 0x100,
+		.fast_io = true,
+	};
+	struct spmi_device *sparent;
 	struct eusb2_repeater *rptr;
+	struct spmi_subdevice *sub_sdev;
 	struct device *dev = &pdev->dev;
 	struct phy_provider *phy_provider;
 	struct device_node *np = dev->of_node;
-	u32 res;
 	int ret;
 
+	if (!dev->parent)
+		return -ENODEV;
+
 	rptr = devm_kzalloc(dev, sizeof(*rptr), GFP_KERNEL);
 	if (!rptr)
 		return -ENOMEM;
@@ -224,15 +232,21 @@ static int eusb2_repeater_probe(struct platform_device *pdev)
 	if (!rptr->cfg)
 		return -EINVAL;
 
-	rptr->regmap = dev_get_regmap(dev->parent, NULL);
-	if (!rptr->regmap)
+	sparent = to_spmi_device(dev->parent);
+	if (!sparent)
 		return -ENODEV;
 
-	ret = of_property_read_u32(np, "reg", &res);
+	sub_sdev = devm_spmi_subdevice_alloc_and_add(dev, sparent);
+	if (IS_ERR(sub_sdev))
+		return PTR_ERR(sub_sdev);
+
+	ret = of_property_read_u32(np, "reg", &eusb2_regmap_config.reg_base);
 	if (ret < 0)
 		return ret;
 
-	rptr->base = res;
+	rptr->regmap = devm_regmap_init_spmi_ext(&sub_sdev->sdev, &eusb2_regmap_config);
+	if (IS_ERR(rptr->regmap))
+		return -ENODEV;
 
 	ret = eusb2_repeater_init_vregs(rptr);
 	if (ret < 0) {
@@ -295,3 +309,4 @@ module_platform_driver(eusb2_repeater_driver);
 
 MODULE_DESCRIPTION("Qualcomm PMIC eUSB2 Repeater driver");
 MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS("SPMI");
-- 
2.51.0