From: Alexander Martinz <amartinz@shiftphones.com>

As with all other devices in commit 7747a49db7e5 ("arm64: dts: qcom:
sc7280-*: Remove thermal zone polling delays"), apply the same change to
this device.

Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
---
 arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts b/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts
index 8d45e6ac0e445b9e20bb9c1520f804623c505653..2efcfb631c3683456794b0a0cc5686f00efd329c 100644
--- a/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts
+++ b/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts
@@ -131,7 +131,7 @@ rmtfs_mem: rmtfs@f8500000 {
 	thermal-zones {
 		camera-thermal {
 			polling-delay-passive = <0>;
-			polling-delay = <0>;
+
 			thermal-sensors = <&pmk8350_adc_tm 2>;
 
 			trips {
@@ -145,7 +145,7 @@ active-config0 {
 
 		chg-skin-thermal {
 			polling-delay-passive = <0>;
-			polling-delay = <0>;
+
 			thermal-sensors = <&pm7250b_adc_tm 0>;
 
 			trips {
@@ -159,7 +159,7 @@ active-config0 {
 
 		conn-thermal {
 			polling-delay-passive = <0>;
-			polling-delay = <0>;
+
 			thermal-sensors = <&pm7250b_adc_tm 1>;
 
 			trips {
@@ -173,7 +173,7 @@ active-config0 {
 
 		quiet-thermal {
 			polling-delay-passive = <0>;
-			polling-delay = <0>;
+
 			thermal-sensors = <&pmk8350_adc_tm 1>;
 
 			trips {
@@ -187,7 +187,7 @@ active-config0 {
 
 		rear-cam-thermal {
 			polling-delay-passive = <0>;
-			polling-delay = <0>;
+
 			thermal-sensors = <&pmk8350_adc_tm 4>;
 
 			trips {
@@ -201,7 +201,7 @@ active-config0 {
 
 		sdm-skin-thermal {
 			polling-delay-passive = <0>;
-			polling-delay = <0>;
+
 			thermal-sensors = <&pmk8350_adc_tm 3>;
 
 			trips {
@@ -215,7 +215,7 @@ active-config0 {
 
 		xo-thermal {
 			polling-delay-passive = <0>;
-			polling-delay = <0>;
+
 			thermal-sensors = <&pmk8350_adc_tm 0>;
 
 			trips {

-- 
2.51.0

On 9/30/25 4:32 PM, Luca Weiss wrote:
> From: Alexander Martinz <amartinz@shiftphones.com>
> 
> As with all other devices in commit 7747a49db7e5 ("arm64: dts: qcom:
> sc7280-*: Remove thermal zone polling delays"), apply the same change to
> this device.

Your passive delays are <0> too (which has been the default value if
absent for a while) - IIRC you don't need either if you just want
userland temperature reporting, but you may need/want it if you hook
up any cooling devices

Konrad