[PATCH v4 0/6] phy: phy-can-transceiver: Support TJA1048/TJA1051

Peng Fan posted 6 patches 1 month ago
There is a newer version of this series
.../devicetree/bindings/phy/ti,tcan104x-can.yaml   |  30 +++++-
arch/arm64/boot/dts/freescale/imx8mp-evk.dts       |  43 +++-----
arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts  |  17 ++-
arch/arm64/boot/dts/freescale/imx95-15x15-evk.dts  |  13 ++-
drivers/phy/phy-can-transceiver.c                  | 120 +++++++++++++++------
5 files changed, 141 insertions(+), 82 deletions(-)
[PATCH v4 0/6] phy: phy-can-transceiver: Support TJA1048/TJA1051
Posted by Peng Fan 1 month ago
TJA1048 is a Dual channel can transceiver with Sleep mode supported.
TJA1051 is a Single Channel can transceiver with Sleep mode supported.

To support them:
patch 1: add binding doc
patch 2/3: To support dual channel,
   - Introduce new flag CAN_TRANSCEIVER_DUAL_CH to indicate the phy
     has two channels.
   - Introduce can_transceiver_priv as a higher level encapsulation for
     phy, mux_state, num_ch.
   - Alloc a phy for each channel
patch 4,5,6: Update dts to use phys

Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
Changes in v4:
- Add R-b from Frank for patch 1, 2, 3, 6
- Address the minor comments from Frank regarding min/maxItems, commit
  log
- Link to v3: https://lore.kernel.org/r/20250829-can-v3-0-3b2f34094f59@nxp.com

Changes in v3:
- Patch 1: Add TJA1057, update #phy-cells
- Patch 2,3: Separate patch 2 into two patches per Frank, 1st introduce
  can_transceiver_priv, 2nd support dual chan by adding num_ch
- Patch 6: Change to 5Mbps rate
- Patch 4,5: Add R-b from Frank
- Link to v2: https://lore.kernel.org/r/20250825-can-v2-0-c461e9fcbc14@nxp.com

Changes in v2:
- Update standby-gpios constraints per Conor's comments
- Drop patch 2 which is not needed.
- Link to v1: https://lore.kernel.org/r/20250822-can-v1-0-c075f702adea@nxp.com

---
Peng Fan (6):
      dt-bindings: phy: ti,tcan104x-can: Document NXP TJA105X/1048
      phy: phy-can-transceiver: Introduce can_transceiver_priv
      phy: phy-can-transceiver: Add dual channel support for TJA1048
      arm64: dts: imx95-15x15-evk: Use phys to replace xceiver-supply
      arm64: dts: imx8mp-evk: Use phys to replace xceiver-supply
      arm64: dts: imx93-11x11-evk: Use phys to replace xceiver-supply

 .../devicetree/bindings/phy/ti,tcan104x-can.yaml   |  30 +++++-
 arch/arm64/boot/dts/freescale/imx8mp-evk.dts       |  43 +++-----
 arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts  |  17 ++-
 arch/arm64/boot/dts/freescale/imx95-15x15-evk.dts  |  13 ++-
 drivers/phy/phy-can-transceiver.c                  | 120 +++++++++++++++------
 5 files changed, 141 insertions(+), 82 deletions(-)
---
base-commit: 6aea185bfe693f3b373488217c198d2c3daed6eb
change-id: 20250821-can-c832cb4f0323

Best regards,
-- 
Peng Fan <peng.fan@nxp.com>