Add support for StarFive VisionFive 2 Lite board

[RFC 2/3] riscv: dts: starfive: jh7110-common: Move out some nodes to the board dts

Posted by Hal Feng 1 month, 1 week ago

Some node in this file are not used by the upcoming VisionFive 2 Lite
board. Move them to the board dts to prepare for adding the new
VisionFive 2 Lite device tree.

Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
---
 .../boot/dts/starfive/jh7110-common.dtsi      | 22 ---------
 .../jh7110-deepcomputing-fml13v01.dts         | 49 +++++++++++++++++++
 .../boot/dts/starfive/jh7110-milkv-mars.dts   | 49 +++++++++++++++++++
 .../dts/starfive/jh7110-pine64-star64.dts     | 49 +++++++++++++++++++
 .../jh7110-starfive-visionfive-2.dtsi         | 46 +++++++++++++++++
 arch/riscv/boot/dts/starfive/jh7110.dtsi      | 16 ------
 6 files changed, 193 insertions(+), 38 deletions(-)

diff --git a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
index 2eaf01775ef5..8332622420ca 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
@@ -281,15 +281,9 @@ &mmc0 {
 	assigned-clock-rates = <50000000>;
 	bus-width = <8>;
 	bootph-pre-ram;
-	cap-mmc-highspeed;
-	mmc-ddr-1_8v;
-	mmc-hs200-1_8v;
-	cap-mmc-hw-reset;
 	post-power-on-delay-ms = <200>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
-	vmmc-supply = <&vcc_3v3>;
-	vqmmc-supply = <&emmc_vdd>;
 	status = "okay";
 };
 
@@ -299,12 +293,7 @@ &mmc1 {
 	assigned-clock-rates = <50000000>;
 	bus-width = <4>;
 	bootph-pre-ram;
-	no-sdio;
-	no-mmc;
-	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
-	disable-wp;
 	cap-sd-highspeed;
-	post-power-on-delay-ms = <200>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins>;
 	status = "okay";
@@ -448,17 +437,6 @@ GPOEN_SYS_I2C6_DATA,
 	};
 
 	mmc0_pins: mmc0-0 {
-		 rst-pins {
-			pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
-					      GPOEN_ENABLE,
-					      GPI_NONE)>;
-			bias-pull-up;
-			drive-strength = <12>;
-			input-disable;
-			input-schmitt-disable;
-			slew-rate = <0>;
-		};
-
 		mmc-pins {
 			pinmux = <PINMUX(PAD_SD0_CLK, 0)>,
 				 <PINMUX(PAD_SD0_CMD, 0)>,
diff --git a/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts b/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts
index f2857d021d68..5a2a41a7e8c3 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts
@@ -11,6 +11,55 @@ / {
 	compatible = "deepcomputing,fml13v01", "starfive,jh7110";
 };
 
+&cpu_opp {
+	opp-375000000 {
+		opp-hz = /bits/ 64 <375000000>;
+		opp-microvolt = <800000>;
+	};
+	opp-500000000 {
+		opp-hz = /bits/ 64 <500000000>;
+		opp-microvolt = <800000>;
+	};
+	opp-750000000 {
+		opp-hz = /bits/ 64 <750000000>;
+		opp-microvolt = <800000>;
+	};
+	opp-1500000000 {
+		opp-hz = /bits/ 64 <1500000000>;
+		opp-microvolt = <1040000>;
+	};
+};
+
+&mmc0 {
+	cap-mmc-highspeed;
+	cap-mmc-hw-reset;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&emmc_vdd>;
+};
+
+&mmc0_pins {
+	rst-pins {
+		pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+				      GPOEN_ENABLE,
+				      GPI_NONE)>;
+		bias-pull-up;
+		drive-strength = <12>;
+		input-disable;
+		input-schmitt-disable;
+		slew-rate = <0>;
+	};
+};
+
+&mmc1 {
+	no-sdio;
+	no-mmc;
+	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	post-power-on-delay-ms = <200>;
+};
+
 &pcie1 {
 	perst-gpios = <&sysgpio 21 GPIO_ACTIVE_LOW>;
 	phys = <&pciephy1>;
diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
index fdaf6b4557da..96f6b2f072d4 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
@@ -11,6 +11,25 @@ / {
 	compatible = "milkv,mars", "starfive,jh7110";
 };
 
+&cpu_opp {
+	opp-375000000 {
+		opp-hz = /bits/ 64 <375000000>;
+		opp-microvolt = <800000>;
+	};
+	opp-500000000 {
+		opp-hz = /bits/ 64 <500000000>;
+		opp-microvolt = <800000>;
+	};
+	opp-750000000 {
+		opp-hz = /bits/ 64 <750000000>;
+		opp-microvolt = <800000>;
+	};
+	opp-1500000000 {
+		opp-hz = /bits/ 64 <1500000000>;
+		opp-microvolt = <1040000>;
+	};
+};
+
 &gmac0 {
 	assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
 	assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>;
@@ -22,6 +41,36 @@ &i2c0 {
 	status = "okay";
 };
 
+&mmc0 {
+	cap-mmc-highspeed;
+	cap-mmc-hw-reset;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&emmc_vdd>;
+};
+
+&mmc0_pins {
+	rst-pins {
+		pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+				      GPOEN_ENABLE,
+				      GPI_NONE)>;
+		bias-pull-up;
+		drive-strength = <12>;
+		input-disable;
+		input-schmitt-disable;
+		slew-rate = <0>;
+	};
+};
+
+&mmc1 {
+	no-sdio;
+	no-mmc;
+	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	post-power-on-delay-ms = <200>;
+};
+
 &pcie0 {
 	status = "okay";
 };
diff --git a/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts b/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts
index 31e825be2065..c9677aef9ff0 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts
@@ -14,6 +14,25 @@ aliases {
 	};
 };
 
+&cpu_opp {
+	opp-375000000 {
+		opp-hz = /bits/ 64 <375000000>;
+		opp-microvolt = <800000>;
+	};
+	opp-500000000 {
+		opp-hz = /bits/ 64 <500000000>;
+		opp-microvolt = <800000>;
+	};
+	opp-750000000 {
+		opp-hz = /bits/ 64 <750000000>;
+		opp-microvolt = <800000>;
+	};
+	opp-1500000000 {
+		opp-hz = /bits/ 64 <1500000000>;
+		opp-microvolt = <1040000>;
+	};
+};
+
 &gmac0 {
 	starfive,tx-use-rgmii-clk;
 	assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
@@ -44,6 +63,36 @@ &i2c0 {
 	status = "okay";
 };
 
+&mmc0 {
+	cap-mmc-highspeed;
+	cap-mmc-hw-reset;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&emmc_vdd>;
+};
+
+&mmc0_pins {
+	rst-pins {
+		pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+				      GPOEN_ENABLE,
+				      GPI_NONE)>;
+		bias-pull-up;
+		drive-strength = <12>;
+		input-disable;
+		input-schmitt-disable;
+		slew-rate = <0>;
+	};
+};
+
+&mmc1 {
+	no-sdio;
+	no-mmc;
+	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	post-power-on-delay-ms = <200>;
+};
+
 &pcie1 {
 	status = "okay";
 };
diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
index 5f14afb2c24d..d1e4206f1251 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
@@ -13,6 +13,25 @@ aliases {
 	};
 };
 
+&cpu_opp {
+	opp-375000000 {
+		opp-hz = /bits/ 64 <375000000>;
+		opp-microvolt = <800000>;
+	};
+	opp-500000000 {
+		opp-hz = /bits/ 64 <500000000>;
+		opp-microvolt = <800000>;
+	};
+	opp-750000000 {
+		opp-hz = /bits/ 64 <750000000>;
+		opp-microvolt = <800000>;
+	};
+	opp-1500000000 {
+		opp-hz = /bits/ 64 <1500000000>;
+		opp-microvolt = <1040000>;
+	};
+};
+
 &gmac0 {
 	status = "okay";
 };
@@ -38,9 +57,36 @@ &i2c0 {
 };
 
 &mmc0 {
+	cap-mmc-highspeed;
+	cap-mmc-hw-reset;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&emmc_vdd>;
 	non-removable;
 };
 
+&mmc0_pins {
+	rst-pins {
+		pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+				      GPOEN_ENABLE,
+				      GPI_NONE)>;
+		bias-pull-up;
+		drive-strength = <12>;
+		input-disable;
+		input-schmitt-disable;
+		slew-rate = <0>;
+	};
+};
+
+&mmc1 {
+	no-sdio;
+	no-mmc;
+	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	post-power-on-delay-ms = <200>;
+};
+
 &pcie0 {
 	status = "okay";
 };
diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
index 0ba74ef04679..d2463399b959 100644
--- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
@@ -200,22 +200,6 @@ core4 {
 	cpu_opp: opp-table-0 {
 			compatible = "operating-points-v2";
 			opp-shared;
-			opp-375000000 {
-					opp-hz = /bits/ 64 <375000000>;
-					opp-microvolt = <800000>;
-			};
-			opp-500000000 {
-					opp-hz = /bits/ 64 <500000000>;
-					opp-microvolt = <800000>;
-			};
-			opp-750000000 {
-					opp-hz = /bits/ 64 <750000000>;
-					opp-microvolt = <800000>;
-			};
-			opp-1500000000 {
-					opp-hz = /bits/ 64 <1500000000>;
-					opp-microvolt = <1040000>;
-			};
 	};
 
 	thermal-zones {
-- 
2.43.2

Re: [RFC 2/3] riscv: dts: starfive: jh7110-common: Move out some nodes to the board dts

Posted by E Shattow 1 month, 1 week ago

On 8/21/25 03:09, Hal Feng wrote:
> Some node in this file are not used by the upcoming VisionFive 2 Lite
> board. Move them to the board dts to prepare for adding the new
> VisionFive 2 Lite device tree.
> 
> Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
> ---
>  .../boot/dts/starfive/jh7110-common.dtsi      | 22 ---------
>  .../jh7110-deepcomputing-fml13v01.dts         | 49 +++++++++++++++++++
>  .../boot/dts/starfive/jh7110-milkv-mars.dts   | 49 +++++++++++++++++++
>  .../dts/starfive/jh7110-pine64-star64.dts     | 49 +++++++++++++++++++
>  .../jh7110-starfive-visionfive-2.dtsi         | 46 +++++++++++++++++
>  arch/riscv/boot/dts/starfive/jh7110.dtsi      | 16 ------
>  6 files changed, 193 insertions(+), 38 deletions(-)
> 
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
> index 2eaf01775ef5..8332622420ca 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
> @@ -281,15 +281,9 @@ &mmc0 {
>  	assigned-clock-rates = <50000000>;
>  	bus-width = <8>;
>  	bootph-pre-ram;
> -	cap-mmc-highspeed;
> -	mmc-ddr-1_8v;
> -	mmc-hs200-1_8v;
> -	cap-mmc-hw-reset;
>  	post-power-on-delay-ms = <200>;
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&mmc0_pins>;
> -	vmmc-supply = <&vcc_3v3>;
> -	vqmmc-supply = <&emmc_vdd>;
>  	status = "okay";
>  };
>  
> @@ -299,12 +293,7 @@ &mmc1 {
>  	assigned-clock-rates = <50000000>;
>  	bus-width = <4>;
>  	bootph-pre-ram;

> -	no-sdio;

drop no-sdio, it is not there in riscv-dt-for-next branch
ref: https://lore.kernel.org/lkml/20250819-sushi-change-1254c2d2a08d@spud/

> -	no-mmc;

similar, I think we should now drop no-mmc unless you can say there is a
defect which requires it. I have tested with Star64 and Milk-V Mars
CM(/-Lite);  if you can confirm with boards you have access to that
'no-mmc' can be dropped then we should just drop it. The correct reason
for having this 'no-mmc' would only be if the controller has an error
when receiving these commands.

> -	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
> -	disable-wp;
>  	cap-sd-highspeed;

> -	post-power-on-delay-ms = <200>;

I would like to know the reason for this delay configuration? Is it
described somewhere in technical documentation or discussion why we have
this?

>  	pinctrl-names = "default";
>  	pinctrl-0 = <&mmc1_pins>;
>  	status = "okay";
> @@ -448,17 +437,6 @@ GPOEN_SYS_I2C6_DATA,
>  	};
>  
>  	mmc0_pins: mmc0-0 {
> -		 rst-pins {
> -			pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
> -					      GPOEN_ENABLE,
> -					      GPI_NONE)>;
> -			bias-pull-up;
> -			drive-strength = <12>;
> -			input-disable;
> -			input-schmitt-disable;
> -			slew-rate = <0>;
> -		};
> -
>  		mmc-pins {
>  			pinmux = <PINMUX(PAD_SD0_CLK, 0)>,
>  				 <PINMUX(PAD_SD0_CMD, 0)>,
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts b/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts
> index f2857d021d68..5a2a41a7e8c3 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts
> +++ b/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts
> @@ -11,6 +11,55 @@ / {
>  	compatible = "deepcomputing,fml13v01", "starfive,jh7110";
>  };
>  
> +&cpu_opp {
> +	opp-375000000 {
> +		opp-hz = /bits/ 64 <375000000>;
> +		opp-microvolt = <800000>;
> +	};
> +	opp-500000000 {
> +		opp-hz = /bits/ 64 <500000000>;
> +		opp-microvolt = <800000>;
> +	};
> +	opp-750000000 {
> +		opp-hz = /bits/ 64 <750000000>;
> +		opp-microvolt = <800000>;
> +	};
> +	opp-1500000000 {
> +		opp-hz = /bits/ 64 <1500000000>;
> +		opp-microvolt = <1040000>;
> +	};
> +};
> +
> +&mmc0 {
> +	cap-mmc-highspeed;
> +	cap-mmc-hw-reset;
> +	mmc-ddr-1_8v;
> +	mmc-hs200-1_8v;
> +	vmmc-supply = <&vcc_3v3>;
> +	vqmmc-supply = <&emmc_vdd>;
> +};
> +
> +&mmc0_pins {
> +	rst-pins {
> +		pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
> +				      GPOEN_ENABLE,
> +				      GPI_NONE)>;
> +		bias-pull-up;
> +		drive-strength = <12>;
> +		input-disable;
> +		input-schmitt-disable;
> +		slew-rate = <0>;
> +	};
> +};
> +
> +&mmc1 {
> +	no-sdio;
> +	no-mmc;
> +	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
> +	disable-wp;
> +	post-power-on-delay-ms = <200>;
> +};
> +
>  &pcie1 {
>  	perst-gpios = <&sysgpio 21 GPIO_ACTIVE_LOW>;
>  	phys = <&pciephy1>;
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
> index fdaf6b4557da..96f6b2f072d4 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
> +++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
> @@ -11,6 +11,25 @@ / {
>  	compatible = "milkv,mars", "starfive,jh7110";
>  };
>  
> +&cpu_opp {
> +	opp-375000000 {
> +		opp-hz = /bits/ 64 <375000000>;
> +		opp-microvolt = <800000>;
> +	};
> +	opp-500000000 {
> +		opp-hz = /bits/ 64 <500000000>;
> +		opp-microvolt = <800000>;
> +	};
> +	opp-750000000 {
> +		opp-hz = /bits/ 64 <750000000>;
> +		opp-microvolt = <800000>;
> +	};
> +	opp-1500000000 {
> +		opp-hz = /bits/ 64 <1500000000>;
> +		opp-microvolt = <1040000>;
> +	};
> +};
> +
>  &gmac0 {
>  	assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
>  	assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>;
> @@ -22,6 +41,36 @@ &i2c0 {
>  	status = "okay";
>  };
>  
> +&mmc0 {
> +	cap-mmc-highspeed;
> +	cap-mmc-hw-reset;
> +	mmc-ddr-1_8v;
> +	mmc-hs200-1_8v;
> +	vmmc-supply = <&vcc_3v3>;
> +	vqmmc-supply = <&emmc_vdd>;
> +};
> +
> +&mmc0_pins {
> +	rst-pins {
> +		pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
> +				      GPOEN_ENABLE,
> +				      GPI_NONE)>;
> +		bias-pull-up;
> +		drive-strength = <12>;
> +		input-disable;
> +		input-schmitt-disable;
> +		slew-rate = <0>;
> +	};
> +};
> +
> +&mmc1 {
> +	no-sdio;
> +	no-mmc;
> +	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
> +	disable-wp;
> +	post-power-on-delay-ms = <200>;
> +};
> +
>  &pcie0 {
>  	status = "okay";
>  };
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts b/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts
> index 31e825be2065..c9677aef9ff0 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts
> +++ b/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts
> @@ -14,6 +14,25 @@ aliases {
>  	};
>  };
>  
> +&cpu_opp {
> +	opp-375000000 {
> +		opp-hz = /bits/ 64 <375000000>;
> +		opp-microvolt = <800000>;
> +	};
> +	opp-500000000 {
> +		opp-hz = /bits/ 64 <500000000>;
> +		opp-microvolt = <800000>;
> +	};
> +	opp-750000000 {
> +		opp-hz = /bits/ 64 <750000000>;
> +		opp-microvolt = <800000>;
> +	};
> +	opp-1500000000 {
> +		opp-hz = /bits/ 64 <1500000000>;
> +		opp-microvolt = <1040000>;
> +	};
> +};
> +
>  &gmac0 {
>  	starfive,tx-use-rgmii-clk;
>  	assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
> @@ -44,6 +63,36 @@ &i2c0 {
>  	status = "okay";
>  };
>  
> +&mmc0 {
> +	cap-mmc-highspeed;
> +	cap-mmc-hw-reset;
> +	mmc-ddr-1_8v;
> +	mmc-hs200-1_8v;
> +	vmmc-supply = <&vcc_3v3>;
> +	vqmmc-supply = <&emmc_vdd>;
> +};
> +
> +&mmc0_pins {
> +	rst-pins {
> +		pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
> +				      GPOEN_ENABLE,
> +				      GPI_NONE)>;
> +		bias-pull-up;
> +		drive-strength = <12>;
> +		input-disable;
> +		input-schmitt-disable;
> +		slew-rate = <0>;
> +	};
> +};
> +
> +&mmc1 {
> +	no-sdio;
> +	no-mmc;
> +	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
> +	disable-wp;
> +	post-power-on-delay-ms = <200>;
> +};
> +
>  &pcie1 {
>  	status = "okay";
>  };
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> index 5f14afb2c24d..d1e4206f1251 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> @@ -13,6 +13,25 @@ aliases {
>  	};
>  };
>  
> +&cpu_opp {
> +	opp-375000000 {
> +		opp-hz = /bits/ 64 <375000000>;
> +		opp-microvolt = <800000>;
> +	};
> +	opp-500000000 {
> +		opp-hz = /bits/ 64 <500000000>;
> +		opp-microvolt = <800000>;
> +	};
> +	opp-750000000 {
> +		opp-hz = /bits/ 64 <750000000>;
> +		opp-microvolt = <800000>;
> +	};
> +	opp-1500000000 {
> +		opp-hz = /bits/ 64 <1500000000>;
> +		opp-microvolt = <1040000>;
> +	};
> +};
> +
>  &gmac0 {
>  	status = "okay";
>  };
> @@ -38,9 +57,36 @@ &i2c0 {
>  };
>  
>  &mmc0 {
> +	cap-mmc-highspeed;
> +	cap-mmc-hw-reset;
> +	mmc-ddr-1_8v;
> +	mmc-hs200-1_8v;
> +	vmmc-supply = <&vcc_3v3>;
> +	vqmmc-supply = <&emmc_vdd>;
>  	non-removable;
>  };
>  
> +&mmc0_pins {
> +	rst-pins {
> +		pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
> +				      GPOEN_ENABLE,
> +				      GPI_NONE)>;
> +		bias-pull-up;
> +		drive-strength = <12>;
> +		input-disable;
> +		input-schmitt-disable;
> +		slew-rate = <0>;
> +	};
> +};
> +
> +&mmc1 {
> +	no-sdio;
> +	no-mmc;
> +	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
> +	disable-wp;
> +	post-power-on-delay-ms = <200>;
> +};
> +
>  &pcie0 {
>  	status = "okay";
>  };
> diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> index 0ba74ef04679..d2463399b959 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> @@ -200,22 +200,6 @@ core4 {
>  	cpu_opp: opp-table-0 {
>  			compatible = "operating-points-v2";
>  			opp-shared;
> -			opp-375000000 {
> -					opp-hz = /bits/ 64 <375000000>;
> -					opp-microvolt = <800000>;
> -			};
> -			opp-500000000 {
> -					opp-hz = /bits/ 64 <500000000>;
> -					opp-microvolt = <800000>;
> -			};
> -			opp-750000000 {
> -					opp-hz = /bits/ 64 <750000000>;
> -					opp-microvolt = <800000>;
> -			};
> -			opp-1500000000 {
> -					opp-hz = /bits/ 64 <1500000000>;
> -					opp-microvolt = <1040000>;
> -			};
>  	};
>  
>  	thermal-zones {

With that,

Reviewed-by: E Shattow <e@freeshell.de>

[RFC 1/3] dt-bindings: riscv: Add StarFive JH7110S SoC and VisionFive 2 Lite board
[RFC 2/3] riscv: dts: starfive: jh7110-common: Move out some nodes to the board dts
[RFC 3/3] riscv: dts: starfive: Add VisionFive 2 Lite board device tree