Milk-V Jupiter uses an RGMII PHY for each port and uses GPIO for PHY
reset.

Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>
---
 arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts | 46 +++++++++++++++++++++++
 1 file changed, 46 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
index 4483192141049caa201c093fb206b6134a064f42..c5933555c06b66f40e61fe2b9c159ba0770c2fa1 100644
--- a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
@@ -20,6 +20,52 @@ chosen {
 	};
 };
 
+&eth0 {
+	phy-handle = <&rgmii0>;
+	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac0_cfg>;
+	rx-internal-delay-ps = <0>;
+	tx-internal-delay-ps = <0>;
+	status = "okay";
+
+	mdio-bus {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		reset-gpios = <&gpio K1_GPIO(110) GPIO_ACTIVE_LOW>;
+		reset-delay-us = <10000>;
+		reset-post-delay-us = <100000>;
+
+		rgmii0: phy@1 {
+			reg = <0x1>;
+		};
+	};
+};
+
+&eth1 {
+	phy-handle = <&rgmii1>;
+	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1_cfg>;
+	rx-internal-delay-ps = <0>;
+	tx-internal-delay-ps = <250>;
+	status = "okay";
+
+	mdio-bus {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		reset-gpios = <&gpio K1_GPIO(115) GPIO_ACTIVE_LOW>;
+		reset-delay-us = <10000>;
+		reset-post-delay-us = <100000>;
+
+		rgmii1: phy@1 {
+			reg = <0x1>;
+		};
+	};
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_2_cfg>;

-- 
2.50.1

Hi Vivian,

On 14:47 Wed 20 Aug     , Vivian Wang wrote:
> Milk-V Jupiter uses an RGMII PHY for each port and uses GPIO for PHY
> reset.
> 
> Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>

Reviewed-by: Yixun Lan <dlan@gentoo.org>
> ---
>  arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts | 46 +++++++++++++++++++++++
>  1 file changed, 46 insertions(+)
> 
> diff --git a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
> index 4483192141049caa201c093fb206b6134a064f42..c5933555c06b66f40e61fe2b9c159ba0770c2fa1 100644
> --- a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
> +++ b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
> @@ -20,6 +20,52 @@ chosen {
>  	};
>  };
>  
> +&eth0 {
> +	phy-handle = <&rgmii0>;
> +	phy-mode = "rgmii-id";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&gmac0_cfg>;
> +	rx-internal-delay-ps = <0>;
> +	tx-internal-delay-ps = <0>;
> +	status = "okay";
> +
> +	mdio-bus {
> +		#address-cells = <0x1>;
> +		#size-cells = <0x0>;
> +
> +		reset-gpios = <&gpio K1_GPIO(110) GPIO_ACTIVE_LOW>;
> +		reset-delay-us = <10000>;
> +		reset-post-delay-us = <100000>;
> +
> +		rgmii0: phy@1 {
> +			reg = <0x1>;
> +		};
> +	};
> +};
> +
> +&eth1 {
> +	phy-handle = <&rgmii1>;
> +	phy-mode = "rgmii-id";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&gmac1_cfg>;
> +	rx-internal-delay-ps = <0>;
> +	tx-internal-delay-ps = <250>;
> +	status = "okay";
> +
> +	mdio-bus {
> +		#address-cells = <0x1>;
> +		#size-cells = <0x0>;
> +
> +		reset-gpios = <&gpio K1_GPIO(115) GPIO_ACTIVE_LOW>;
> +		reset-delay-us = <10000>;
> +		reset-post-delay-us = <100000>;
> +
> +		rgmii1: phy@1 {
> +			reg = <0x1>;
> +		};
> +	};
> +};
> +
>  &uart0 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&uart0_2_cfg>;
> 
> -- 
> 2.50.1
> 

-- 
Yixun Lan (dlan)