Add device tree nodes to enable Bluetooth in the Ampak AP6275P module
found on Rockchip RK3576 EVB1 and connected over a UART link.

Note that this doesn't enable the out-of-band PCM connection. It's
routed to SAI2 M0 pins in case anyone wishes to add it.

Tested-by: Pavel Zhovner <pavel@flipperdevices.com>
Signed-off-by: Alexey Charkov <alchark@gmail.com>
---
 arch/arm64/boot/dts/rockchip/rk3576-evb1-v10.dts | 35 ++++++++++++++++++++++++
 1 file changed, 35 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3576-evb1-v10.dts b/arch/arm64/boot/dts/rockchip/rk3576-evb1-v10.dts
index 100ca2e23c6093ae517d741fcd047e2a8172f457..d3e70a646fbe1e99cb007e7d9f09da33beedc842 100644
--- a/arch/arm64/boot/dts/rockchip/rk3576-evb1-v10.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3576-evb1-v10.dts
@@ -766,6 +766,20 @@ &pcie1 {
 };
 
 &pinctrl {
+	bluetooth {
+		bt_reg_on: bt-reg-on {
+			rockchip,pins = <1 RK_PC7 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		bt_wake_host: bt-wake-host {
+			rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		host_wake_bt: host-wake-bt {
+			rockchip,pins = <1 RK_PD4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
 	hym8563 {
 		rtc_int: rtc-int {
 			rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>;
@@ -843,6 +857,27 @@ &uart0 {
 	status = "okay";
 };
 
+&uart4 {
+	pinctrl-0 = <&uart4m1_xfer &uart4m1_ctsn &uart4m1_rtsn>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&hym8563>;
+		clock-names = "lpo";
+		device-wakeup-gpios = <&gpio1 RK_PD4 GPIO_ACTIVE_HIGH>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PB1 IRQ_TYPE_LEVEL_HIGH>;
+		pinctrl-0 = <&bt_reg_on &bt_wake_host &host_wake_bt>;
+		pinctrl-names = "default";
+		shutdown-gpios = <&gpio1 RK_PC7 GPIO_ACTIVE_HIGH>;
+		vbat-supply = <&vcc_3v3_s3>;
+		vddio-supply = <&vcc_1v8_s3>;
+	};
+};
+
 &ufshc {
 	status = "okay";
 };

-- 
2.49.1