From: Li Liu <quic_lliu6@quicinc.com>

Add display MDSS and DSI configuration for QCS615 RIDE board.
QCS615 has a DP port, and DP support will be added in a later patch.

Signed-off-by: Li Liu <quic_lliu6@quicinc.com>
Signed-off-by: Fange Zhang <fange.zhang@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/qcs615-ride.dts | 90 ++++++++++++++++++++++++++++++++
 1 file changed, 90 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcs615-ride.dts b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
index a6652e4817d1c218c7981b04daeb035e2852ac1a..f41e0763170df40c5d10497049ae74ab4aee4950 100644
--- a/arch/arm64/boot/dts/qcom/qcs615-ride.dts
+++ b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
@@ -38,6 +38,18 @@ xo_board_clk: xo-board-clk {
 		};
 	};
 
+	dp-dsi0-connector {
+		compatible = "dp-connector";
+		label = "DSI0";
+		type = "mini";
+
+		port {
+			dp_dsi0_connector_in: endpoint {
+				remote-endpoint = <&dsi2dp_bridge_out>;
+			};
+		};
+	};
+
 	regulator-usb2-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "USB2_VBUS";
@@ -217,6 +229,84 @@ &gcc {
 		 <&sleep_clk>;
 };
 
+&i2c2 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	io_expander: gpio@3e {
+		compatible = "semtech,sx1509q";
+		reg = <0x3e>;
+		interrupts-extended = <&tlmm 58 IRQ_TYPE_EDGE_FALLING>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		semtech,probe-reset;
+	};
+
+	i2c-mux@77 {
+		compatible = "nxp,pca9542";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			bridge@58 {
+				compatible = "analogix,anx7625";
+				reg = <0x58>;
+				interrupts-extended = <&io_expander 0 IRQ_TYPE_EDGE_FALLING>;
+				enable-gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
+				reset-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
+				wakeup-source;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						dsi2dp_bridge_in: endpoint {
+							remote-endpoint = <&mdss_dsi0_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						dsi2dp_bridge_out: endpoint {
+							remote-endpoint = <&dp_dsi0_connector_in>;
+						};
+					};
+				};
+			};
+		};
+	};
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	vdda-supply = <&vreg_l11a>;
+	status = "okay";
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&dsi2dp_bridge_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	vdds-supply = <&vreg_l5a>;
+	status = "okay";
+};
+
 &pm8150_gpios {
 	usb2_en: usb2-en-state {
 		pins = "gpio10";

-- 
2.34.1

On Fri, Jul 18, 2025 at 08:56:33PM +0800, Fange Zhang wrote:
> From: Li Liu <quic_lliu6@quicinc.com>
> 
> Add display MDSS and DSI configuration for QCS615 RIDE board.
> QCS615 has a DP port, and DP support will be added in a later patch.
> 
> Signed-off-by: Li Liu <quic_lliu6@quicinc.com>
> Signed-off-by: Fange Zhang <fange.zhang@oss.qualcomm.com>
> ---
>  arch/arm64/boot/dts/qcom/qcs615-ride.dts | 90 ++++++++++++++++++++++++++++++++
>  1 file changed, 90 insertions(+)
> 

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>


-- 
With best wishes
Dmitry