From: Samuel Kayode <samuel.kayode@savoirfairelinux.com>

Add support for the battery charger for pf1550 PMIC.

Signed-off-by: Samuel Kayode <samuel.kayode@savoirfairelinux.com>
---
v8:
- Drop PF1550_CHARGER_NAME
- Drop unnecessary POWER_SUPPLY_STATUS_CHARGING s
- Replace POWER_SUPPLY_HEALTH_DEAD with POWER_SUPPLY_HEALTH_NO_BATTERY
- Drop check for charger in delayed_work s
- Use dev_warn when battery is over-voltage
- Define two power supplies: charger and battery
- Use devm_delayed_work_autocancel to automate cleanup and fix race
  condition
v7:
- Use reverse christmas tree order
- Drop unecessary 0 in id table's driver data field
- Store virqs to avoid reinvoking platform_get_irq in the interrupt
  service routine
- Drop manufacturer and model global variables
v6:
- Drop lock entirely
- Reverse christmas tree order for variables defined in probe as
  suggested by Frank
- return pf1550_reg_init
v5:
- Drop lock for battery and charger delayed_work
- More conservative locking in vbus delayed_work
- Apply lock when setting power supply type during register initialization
v4:
- Finish handling of some interrupts in threaded irq handler
- Use platform_get_irq
v3:
- Use struct power_supply_get_battery_info to get constant charge
  voltage if specified
- Use virqs mapped in MFD driver
v2:
- Address feedback from Enric Balletbo Serra
---
 drivers/power/supply/Kconfig          |  11 +
 drivers/power/supply/Makefile         |   1 +
 drivers/power/supply/pf1550-charger.c | 632 ++++++++++++++++++++++++++++++++++
 3 files changed, 644 insertions(+)

diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
index 79ddb006e2dad6bf96b71ed570a37c006b5f9433..6d0c872edac1f45da314632e671af1aeda4c87b8 100644
--- a/drivers/power/supply/Kconfig
+++ b/drivers/power/supply/Kconfig
@@ -471,6 +471,17 @@ config CHARGER_88PM860X
 	help
 	  Say Y here to enable charger for Marvell 88PM860x chip.
 
+config CHARGER_PF1550
+	tristate "NXP PF1550 battery charger driver"
+	depends on MFD_PF1550
+	help
+	  Say Y to enable support for the NXP PF1550 battery charger.
+	  The device is a single cell Li-Ion/Li-Polymer battery charger for
+	  portable application.
+
+	  This driver can also be built as a module. If so, the module will be
+	  called pf1550-charger.
+
 config BATTERY_RX51
 	tristate "Nokia RX-51 (N900) battery driver"
 	depends on TWL4030_MADC
diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
index 4f5f8e3507f80da02812f0d08c2d81ddff0a272f..7f68380099c59dab71b73120150612a23e16a745 100644
--- a/drivers/power/supply/Makefile
+++ b/drivers/power/supply/Makefile
@@ -64,6 +64,7 @@ obj-$(CONFIG_CHARGER_RT9467)	+= rt9467-charger.o
 obj-$(CONFIG_CHARGER_RT9471)	+= rt9471.o
 obj-$(CONFIG_BATTERY_TWL4030_MADC)	+= twl4030_madc_battery.o
 obj-$(CONFIG_CHARGER_88PM860X)	+= 88pm860x_charger.o
+obj-$(CONFIG_CHARGER_PF1550)	+= pf1550-charger.o
 obj-$(CONFIG_BATTERY_RX51)	+= rx51_battery.o
 obj-$(CONFIG_AB8500_BM)		+= ab8500_bmdata.o ab8500_charger.o ab8500_fg.o ab8500_btemp.o ab8500_chargalg.o
 obj-$(CONFIG_CHARGER_CPCAP)	+= cpcap-charger.o
diff --git a/drivers/power/supply/pf1550-charger.c b/drivers/power/supply/pf1550-charger.c
new file mode 100644
index 0000000000000000000000000000000000000000..7a6bd9c30d60280f1e1c50d4e1ddaf0a4998b9f0
--- /dev/null
+++ b/drivers/power/supply/pf1550-charger.c
@@ -0,0 +1,632 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * charger driver for the PF1550
+ *
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ * Robin Gong <yibin.gong@freescale.com>
+ *
+ * Portions Copyright (c) 2025 Savoir-faire Linux Inc.
+ * Samuel Kayode <samuel.kayode@savoirfairelinux.com>
+ */
+
+#include <linux/devm-helpers.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/pf1550.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+
+#define PF1550_DEFAULT_CONSTANT_VOLT	4200000
+#define PF1550_DEFAULT_MIN_SYSTEM_VOLT	3500000
+#define PF1550_DEFAULT_THERMAL_TEMP	75
+#define PF1550_CHARGER_IRQ_NR		5
+
+struct pf1550_charger {
+	struct device *dev;
+	const struct pf1550_ddata *pf1550;
+	struct power_supply *charger;
+	struct power_supply *battery;
+	struct delayed_work vbus_sense_work;
+	struct delayed_work chg_sense_work;
+	struct delayed_work bat_sense_work;
+	int virqs[PF1550_CHARGER_IRQ_NR];
+
+	u32 constant_volt;
+	u32 min_system_volt;
+	u32 thermal_regulation_temp;
+};
+
+static int pf1550_get_charger_state(struct regmap *regmap, int *val)
+{
+	unsigned int data;
+	int ret;
+
+	ret = regmap_read(regmap, PF1550_CHARG_REG_CHG_SNS, &data);
+	if (ret < 0)
+		return ret;
+
+	data &= PF1550_CHG_SNS_MASK;
+
+	switch (data) {
+	case PF1550_CHG_PRECHARGE:
+	case PF1550_CHG_CONSTANT_CURRENT:
+	case PF1550_CHG_CONSTANT_VOL:
+	case PF1550_CHG_EOC:
+		*val = POWER_SUPPLY_STATUS_CHARGING;
+		break;
+	case PF1550_CHG_DONE:
+		*val = POWER_SUPPLY_STATUS_FULL;
+		break;
+	case PF1550_CHG_TIMER_FAULT:
+	case PF1550_CHG_SUSPEND:
+		*val = POWER_SUPPLY_STATUS_NOT_CHARGING;
+		break;
+	case PF1550_CHG_OFF_INV:
+	case PF1550_CHG_OFF_TEMP:
+	case PF1550_CHG_LINEAR_ONLY:
+		*val = POWER_SUPPLY_STATUS_DISCHARGING;
+		break;
+	default:
+		*val = POWER_SUPPLY_STATUS_UNKNOWN;
+	}
+
+	return 0;
+}
+
+static int pf1550_get_charge_type(struct regmap *regmap, int *val)
+{
+	unsigned int data;
+	int ret;
+
+	ret = regmap_read(regmap, PF1550_CHARG_REG_CHG_SNS, &data);
+	if (ret < 0)
+		return ret;
+
+	data &= PF1550_CHG_SNS_MASK;
+
+	switch (data) {
+	case PF1550_CHG_SNS_MASK:
+		*val = POWER_SUPPLY_CHARGE_TYPE_TRICKLE;
+		break;
+	case PF1550_CHG_CONSTANT_CURRENT:
+	case PF1550_CHG_CONSTANT_VOL:
+	case PF1550_CHG_EOC:
+		*val = POWER_SUPPLY_CHARGE_TYPE_FAST;
+		break;
+	case PF1550_CHG_DONE:
+	case PF1550_CHG_TIMER_FAULT:
+	case PF1550_CHG_SUSPEND:
+	case PF1550_CHG_OFF_INV:
+	case PF1550_CHG_BAT_OVER:
+	case PF1550_CHG_OFF_TEMP:
+	case PF1550_CHG_LINEAR_ONLY:
+		*val = POWER_SUPPLY_CHARGE_TYPE_NONE;
+		break;
+	default:
+		*val = POWER_SUPPLY_CHARGE_TYPE_UNKNOWN;
+	}
+
+	return 0;
+}
+
+/*
+ * Supported health statuses:
+ *  - POWER_SUPPLY_HEALTH_DEAD
+ *  - POWER_SUPPLY_HEALTH_GOOD
+ *  - POWER_SUPPLY_HEALTH_OVERVOLTAGE
+ *  - POWER_SUPPLY_HEALTH_UNKNOWN
+ */
+static int pf1550_get_battery_health(struct regmap *regmap, int *val)
+{
+	unsigned int data;
+	int ret;
+
+	ret = regmap_read(regmap, PF1550_CHARG_REG_BATT_SNS, &data);
+	if (ret < 0)
+		return ret;
+
+	data &= PF1550_BAT_SNS_MASK;
+
+	switch (data) {
+	case PF1550_BAT_NO_DETECT:
+		*val = POWER_SUPPLY_HEALTH_NO_BATTERY;
+		break;
+	case PF1550_BAT_NO_VBUS:
+	case PF1550_BAT_LOW_THAN_PRECHARG:
+	case PF1550_BAT_CHARG_FAIL:
+	case PF1550_BAT_HIGH_THAN_PRECHARG:
+		*val = POWER_SUPPLY_HEALTH_GOOD;
+		break;
+	case PF1550_BAT_OVER_VOL:
+		*val = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
+		break;
+	default:
+		*val = POWER_SUPPLY_HEALTH_UNKNOWN;
+		break;
+	}
+
+	return 0;
+}
+
+static int pf1550_get_present(struct regmap *regmap, int *val)
+{
+	unsigned int data;
+	int ret;
+
+	ret = regmap_read(regmap, PF1550_CHARG_REG_BATT_SNS, &data);
+	if (ret < 0)
+		return ret;
+
+	data &= PF1550_BAT_SNS_MASK;
+	*val = (data == PF1550_BAT_NO_DETECT) ? 0 : 1;
+
+	return 0;
+}
+
+static int pf1550_get_online(struct regmap *regmap, int *val)
+{
+	unsigned int data;
+	int ret;
+
+	ret = regmap_read(regmap, PF1550_CHARG_REG_VBUS_SNS, &data);
+	if (ret < 0)
+		return ret;
+
+	*val = (data & PF1550_VBUS_VALID) ? 1 : 0;
+
+	return 0;
+}
+
+static void pf1550_chg_bat_work(struct work_struct *work)
+{
+	struct pf1550_charger *chg = container_of(to_delayed_work(work),
+						  struct pf1550_charger,
+						  bat_sense_work);
+	unsigned int data;
+
+	if (regmap_read(chg->pf1550->regmap, PF1550_CHARG_REG_BATT_SNS, &data)) {
+		dev_err(chg->dev, "Read BATT_SNS error.\n");
+		return;
+	}
+
+	switch (data & PF1550_BAT_SNS_MASK) {
+	case PF1550_BAT_NO_VBUS:
+		dev_dbg(chg->dev, "No valid VBUS input.\n");
+		break;
+	case PF1550_BAT_LOW_THAN_PRECHARG:
+		dev_dbg(chg->dev, "VBAT < VPRECHG.LB.\n");
+		break;
+	case PF1550_BAT_CHARG_FAIL:
+		dev_dbg(chg->dev, "Battery charging failed.\n");
+		break;
+	case PF1550_BAT_HIGH_THAN_PRECHARG:
+		dev_dbg(chg->dev, "VBAT > VPRECHG.LB.\n");
+		break;
+	case PF1550_BAT_OVER_VOL:
+		dev_dbg(chg->dev, "VBAT > VBATOV.\n");
+		break;
+	case PF1550_BAT_NO_DETECT:
+		dev_dbg(chg->dev, "Battery not detected.\n");
+		break;
+	default:
+		dev_err(chg->dev, "Unknown value read:%x\n",
+			data & PF1550_CHG_SNS_MASK);
+	}
+}
+
+static void pf1550_chg_chg_work(struct work_struct *work)
+{
+	struct pf1550_charger *chg = container_of(to_delayed_work(work),
+						  struct pf1550_charger,
+						  chg_sense_work);
+	unsigned int data;
+
+	if (regmap_read(chg->pf1550->regmap, PF1550_CHARG_REG_CHG_SNS, &data)) {
+		dev_err(chg->dev, "Read CHG_SNS error.\n");
+		return;
+	}
+
+	switch (data & PF1550_CHG_SNS_MASK) {
+	case PF1550_CHG_PRECHARGE:
+		dev_dbg(chg->dev, "In pre-charger mode.\n");
+		break;
+	case PF1550_CHG_CONSTANT_CURRENT:
+		dev_dbg(chg->dev, "In fast-charge constant current mode.\n");
+		break;
+	case PF1550_CHG_CONSTANT_VOL:
+		dev_dbg(chg->dev, "In fast-charge constant voltage mode.\n");
+		break;
+	case PF1550_CHG_EOC:
+		dev_dbg(chg->dev, "In EOC mode.\n");
+		break;
+	case PF1550_CHG_DONE:
+		dev_dbg(chg->dev, "In DONE mode.\n");
+		break;
+	case PF1550_CHG_TIMER_FAULT:
+		dev_info(chg->dev, "In timer fault mode.\n");
+		break;
+	case PF1550_CHG_SUSPEND:
+		dev_info(chg->dev, "In thermistor suspend mode.\n");
+		break;
+	case PF1550_CHG_OFF_INV:
+		dev_info(chg->dev, "Input invalid, charger off.\n");
+		break;
+	case PF1550_CHG_BAT_OVER:
+		dev_warn(chg->dev, "Battery over-voltage.\n");
+		break;
+	case PF1550_CHG_OFF_TEMP:
+		dev_info(chg->dev, "Temp high, charger off.\n");
+		break;
+	case PF1550_CHG_LINEAR_ONLY:
+		dev_dbg(chg->dev, "In Linear mode, not charging.\n");
+		break;
+	default:
+		dev_err(chg->dev, "Unknown value read:%x\n",
+			data & PF1550_CHG_SNS_MASK);
+	}
+}
+
+static void pf1550_chg_vbus_work(struct work_struct *work)
+{
+	struct pf1550_charger *chg = container_of(to_delayed_work(work),
+						  struct pf1550_charger,
+						  vbus_sense_work);
+	unsigned int data;
+
+	if (regmap_read(chg->pf1550->regmap, PF1550_CHARG_REG_VBUS_SNS, &data)) {
+		dev_err(chg->dev, "Read VBUS_SNS error.\n");
+		return;
+	}
+
+	if (data & PF1550_VBUS_UVLO) {
+		dev_dbg(chg->dev, "VBUS detached.\n");
+		power_supply_changed(chg->battery);
+	}
+	if (data & PF1550_VBUS_IN2SYS)
+		dev_dbg(chg->dev, "VBUS_IN2SYS_SNS.\n");
+	if (data & PF1550_VBUS_OVLO)
+		dev_dbg(chg->dev, "VBUS_OVLO_SNS.\n");
+	if (data & PF1550_VBUS_VALID) {
+		dev_dbg(chg->dev, "VBUS attached.\n");
+		power_supply_changed(chg->charger);
+	}
+}
+
+static irqreturn_t pf1550_charger_irq_handler(int irq, void *data)
+{
+	struct pf1550_charger *chg = data;
+	struct device *dev = chg->dev;
+	int i, irq_type = -1;
+
+	for (i = 0; i < PF1550_CHARGER_IRQ_NR; i++)
+		if (irq == chg->virqs[i])
+			irq_type = i;
+
+	switch (irq_type) {
+	case PF1550_CHARG_IRQ_BAT2SOCI:
+		dev_info(dev, "BAT to SYS Overcurrent interrupt.\n");
+		break;
+	case PF1550_CHARG_IRQ_BATI:
+		schedule_delayed_work(&chg->bat_sense_work,
+				      msecs_to_jiffies(10));
+		break;
+	case PF1550_CHARG_IRQ_CHGI:
+		schedule_delayed_work(&chg->chg_sense_work,
+				      msecs_to_jiffies(10));
+		break;
+	case PF1550_CHARG_IRQ_VBUSI:
+		schedule_delayed_work(&chg->vbus_sense_work,
+				      msecs_to_jiffies(10));
+		break;
+	case PF1550_CHARG_IRQ_THMI:
+		dev_info(dev, "Thermal interrupt.\n");
+		break;
+	default:
+		dev_err(dev, "unknown interrupt occurred.\n");
+	}
+
+	return IRQ_HANDLED;
+}
+
+static enum power_supply_property pf1550_charger_props[] = {
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_CHARGE_TYPE,
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_ONLINE,
+	POWER_SUPPLY_PROP_MODEL_NAME,
+	POWER_SUPPLY_PROP_MANUFACTURER,
+};
+
+static int pf1550_charger_get_property(struct power_supply *psy,
+				       enum power_supply_property psp,
+				       union power_supply_propval *val)
+{
+	struct pf1550_charger *chg = power_supply_get_drvdata(psy);
+	struct regmap *regmap = chg->pf1550->regmap;
+	int ret = 0;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_STATUS:
+		ret = pf1550_get_charger_state(regmap, &val->intval);
+		break;
+	case POWER_SUPPLY_PROP_CHARGE_TYPE:
+		ret = pf1550_get_charge_type(regmap, &val->intval);
+		break;
+	case POWER_SUPPLY_PROP_HEALTH:
+		ret = pf1550_get_battery_health(regmap, &val->intval);
+		break;
+	case POWER_SUPPLY_PROP_PRESENT:
+		ret = pf1550_get_present(regmap, &val->intval);
+		break;
+	case POWER_SUPPLY_PROP_ONLINE:
+		ret = pf1550_get_online(regmap, &val->intval);
+		break;
+	case POWER_SUPPLY_PROP_MODEL_NAME:
+		val->strval = "PF1550";
+		break;
+	case POWER_SUPPLY_PROP_MANUFACTURER:
+		val->strval = "NXP";
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return ret;
+}
+
+static const struct power_supply_desc pf1550_charger_desc = {
+	.name = "pf1550-charger",
+	.type = POWER_SUPPLY_TYPE_MAINS,
+	.properties = pf1550_charger_props,
+	.num_properties = ARRAY_SIZE(pf1550_charger_props),
+	.get_property = pf1550_charger_get_property,
+};
+
+static const struct power_supply_desc pf1550_battery_desc = {
+	.name = "pf1550-battery",
+	.type = POWER_SUPPLY_TYPE_BATTERY,
+	.properties = pf1550_charger_props,
+	.num_properties = ARRAY_SIZE(pf1550_charger_props),
+	.get_property = pf1550_charger_get_property,
+};
+
+static int pf1550_set_constant_volt(struct pf1550_charger *chg,
+				    unsigned int uvolt)
+{
+	unsigned int data;
+
+	if (uvolt >= 3500000 && uvolt <= 4440000)
+		data = 8 + (uvolt - 3500000) / 20000;
+	else
+		return dev_err_probe(chg->dev, -EINVAL,
+				     "Wrong value for constant voltage\n");
+
+	dev_dbg(chg->dev, "Charging constant voltage: %u (0x%x)\n", uvolt,
+		data);
+
+	return regmap_update_bits(chg->pf1550->regmap,
+				  PF1550_CHARG_REG_BATT_REG,
+				  PF1550_CHARG_REG_BATT_REG_CHGCV_MASK, data);
+}
+
+static int pf1550_set_min_system_volt(struct pf1550_charger *chg,
+				      unsigned int uvolt)
+{
+	unsigned int data;
+
+	switch (uvolt) {
+	case 3500000:
+		data = 0x0;
+		break;
+	case 3700000:
+		data = 0x1;
+		break;
+	case 4300000:
+		data = 0x2;
+		break;
+	default:
+		return dev_err_probe(chg->dev, -EINVAL,
+				     "Wrong value for minimum system voltage\n");
+	}
+
+	data <<= PF1550_CHARG_REG_BATT_REG_VMINSYS_SHIFT;
+
+	dev_dbg(chg->dev, "Minimum system regulation voltage: %u (0x%x)\n",
+		uvolt, data);
+
+	return regmap_update_bits(chg->pf1550->regmap,
+				  PF1550_CHARG_REG_BATT_REG,
+				  PF1550_CHARG_REG_BATT_REG_VMINSYS_MASK, data);
+}
+
+static int pf1550_set_thermal_regulation_temp(struct pf1550_charger *chg,
+					      unsigned int cells)
+{
+	unsigned int data;
+
+	switch (cells) {
+	case 60:
+		data = 0x0;
+		break;
+	case 75:
+		data = 0x1;
+		break;
+	case 90:
+		data = 0x2;
+		break;
+	case 105:
+		data = 0x3;
+		break;
+	default:
+		return dev_err_probe(chg->dev, -EINVAL,
+				     "Wrong value for thermal temperature\n");
+	}
+
+	data <<= PF1550_CHARG_REG_THM_REG_CNFG_REGTEMP_SHIFT;
+
+	dev_dbg(chg->dev, "Thermal regulation loop temperature: %u (0x%x)\n",
+		cells, data);
+
+	return regmap_update_bits(chg->pf1550->regmap,
+				  PF1550_CHARG_REG_THM_REG_CNFG,
+				  PF1550_CHARG_REG_THM_REG_CNFG_REGTEMP_MASK,
+				  data);
+}
+
+/*
+ * Sets charger registers to proper and safe default values.
+ */
+static int pf1550_reg_init(struct pf1550_charger *chg)
+{
+	struct device *dev = chg->dev;
+	unsigned int data;
+	int ret;
+
+	/* Unmask charger interrupt, mask DPMI and reserved bit */
+	ret =  regmap_write(chg->pf1550->regmap, PF1550_CHARG_REG_CHG_INT_MASK,
+			    PF1550_CHG_INT_MASK);
+	if (ret)
+		return dev_err_probe(dev, ret,
+				     "Error unmask charger interrupt\n");
+
+	ret = regmap_read(chg->pf1550->regmap, PF1550_CHARG_REG_VBUS_SNS,
+			  &data);
+	if (ret)
+		return dev_err_probe(dev, ret, "Read charg vbus_sns error\n");
+
+	ret = pf1550_set_constant_volt(chg, chg->constant_volt);
+	if (ret)
+		return ret;
+
+	ret = pf1550_set_min_system_volt(chg, chg->min_system_volt);
+	if (ret)
+		return ret;
+
+	ret = pf1550_set_thermal_regulation_temp(chg,
+						 chg->thermal_regulation_temp);
+	if (ret)
+		return ret;
+
+	/* Turn on charger */
+	ret = regmap_write(chg->pf1550->regmap, PF1550_CHARG_REG_CHG_OPER,
+			   PF1550_CHG_TURNON);
+	if (ret)
+		return dev_err_probe(dev, ret, "Error turn on charger\n");
+
+	return 0;
+}
+
+static void pf1550_dt_parse_dev_info(struct pf1550_charger *chg)
+{
+	struct power_supply_battery_info *info;
+	struct device *dev = chg->dev;
+
+	if (device_property_read_u32(dev->parent, "nxp,min-system-microvolt",
+				     &chg->min_system_volt))
+		chg->min_system_volt = PF1550_DEFAULT_MIN_SYSTEM_VOLT;
+
+	if (device_property_read_u32(dev->parent,
+				     "nxp,thermal-regulation-celsius",
+				     &chg->thermal_regulation_temp))
+		chg->thermal_regulation_temp = PF1550_DEFAULT_THERMAL_TEMP;
+
+	if (power_supply_get_battery_info(chg->charger, &info))
+		chg->constant_volt = PF1550_DEFAULT_CONSTANT_VOLT;
+	else
+		chg->constant_volt = info->constant_charge_voltage_max_uv;
+}
+
+static int pf1550_charger_probe(struct platform_device *pdev)
+{
+	const struct pf1550_ddata *pf1550 = dev_get_drvdata(pdev->dev.parent);
+	struct power_supply_config psy_cfg = {};
+	struct pf1550_charger *chg;
+	int i, irq, ret;
+
+	chg = devm_kzalloc(&pdev->dev, sizeof(*chg), GFP_KERNEL);
+	if (!chg)
+		return -ENOMEM;
+
+	chg->dev = &pdev->dev;
+	chg->pf1550 = pf1550;
+
+	if (!chg->pf1550->regmap)
+		return dev_err_probe(&pdev->dev, -ENODEV,
+				     "failed to get regmap\n");
+
+	platform_set_drvdata(pdev, chg);
+
+	ret = devm_delayed_work_autocancel(chg->dev, &chg->vbus_sense_work,
+					   pf1550_chg_vbus_work);
+	if (ret)
+		return dev_err_probe(chg->dev, ret,
+				     "failed to add vbus sense work\n");
+
+	ret = devm_delayed_work_autocancel(chg->dev, &chg->chg_sense_work,
+					   pf1550_chg_chg_work);
+	if (ret)
+		return dev_err_probe(chg->dev, ret,
+				     "failed to add charger sense work\n");
+
+	ret = devm_delayed_work_autocancel(chg->dev, &chg->bat_sense_work,
+					   pf1550_chg_bat_work);
+	if (ret)
+		return dev_err_probe(chg->dev, ret,
+				     "failed to add battery sense work\n");
+
+	for (i = 0; i < PF1550_CHARGER_IRQ_NR; i++) {
+		irq = platform_get_irq(pdev, i);
+		if (irq < 0)
+			return irq;
+
+		chg->virqs[i] = irq;
+
+		ret = devm_request_threaded_irq(&pdev->dev, irq, NULL,
+						pf1550_charger_irq_handler,
+						IRQF_NO_SUSPEND,
+						"pf1550-charger", chg);
+		if (ret)
+			return dev_err_probe(&pdev->dev, ret,
+					     "failed irq request\n");
+	}
+
+	psy_cfg.drv_data = chg;
+
+	chg->charger = devm_power_supply_register(&pdev->dev,
+						  &pf1550_charger_desc,
+						  &psy_cfg);
+	if (IS_ERR(chg->charger))
+		return dev_err_probe(&pdev->dev, PTR_ERR(chg->charger),
+				     "failed: power supply register\n");
+
+	chg->battery = devm_power_supply_register(&pdev->dev,
+						  &pf1550_battery_desc,
+						  &psy_cfg);
+	if (IS_ERR(chg->battery))
+		return dev_err_probe(&pdev->dev, PTR_ERR(chg->battery),
+				     "failed: power supply register\n");
+
+	pf1550_dt_parse_dev_info(chg);
+
+	return pf1550_reg_init(chg);
+}
+
+static const struct platform_device_id pf1550_charger_id[] = {
+	{ "pf1550-charger", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(platform, pf1550_charger_id);
+
+static struct platform_driver pf1550_charger_driver = {
+	.driver = {
+		.name	= "pf1550-charger",
+	},
+	.probe		= pf1550_charger_probe,
+	.id_table	= pf1550_charger_id,
+};
+module_platform_driver(pf1550_charger_driver);
+
+MODULE_AUTHOR("Robin Gong <yibin.gong@freescale.com>");
+MODULE_DESCRIPTION("PF1550 charger driver");
+MODULE_LICENSE("GPL");

-- 
2.49.0

Hi,

On Mon, Jul 07, 2025 at 05:37:24PM +0100, Samuel Kayode wrote:
> Add support for the battery charger for pf1550 PMIC.
> 
> Signed-off-by: Samuel Kayode <samuel.kayode@savoirfairelinux.com>
> ---

[...]

> diff --git a/drivers/power/supply/pf1550-charger.c b/drivers/power/supply/pf1550-charger.c
> new file mode 100644
> index 0000000000000000000000000000000000000000..7a6bd9c30d60280f1e1c50d4e1ddaf0a4998b9f0
> --- /dev/null
> +++ b/drivers/power/supply/pf1550-charger.c
> @@ -0,0 +1,632 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * charger driver for the PF1550
> + *
> + * Copyright (C) 2016 Freescale Semiconductor, Inc.
> + * Robin Gong <yibin.gong@freescale.com>
> + *
> + * Portions Copyright (c) 2025 Savoir-faire Linux Inc.
> + * Samuel Kayode <samuel.kayode@savoirfairelinux.com>
> + */
> +
> +#include <linux/devm-helpers.h>
> +#include <linux/interrupt.h>
> +#include <linux/mfd/pf1550.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/power_supply.h>
> +
> +#define PF1550_DEFAULT_CONSTANT_VOLT	4200000
> +#define PF1550_DEFAULT_MIN_SYSTEM_VOLT	3500000
> +#define PF1550_DEFAULT_THERMAL_TEMP	75

Default is 95

> +#define PF1550_CHARGER_IRQ_NR		5
> +
> +struct pf1550_charger {
> +	struct device *dev;
> +	const struct pf1550_ddata *pf1550;
> +	struct power_supply *charger;
> +	struct power_supply *battery;
> +	struct delayed_work vbus_sense_work;
> +	struct delayed_work chg_sense_work;
> +	struct delayed_work bat_sense_work;
> +	int virqs[PF1550_CHARGER_IRQ_NR];
> +

[...]

> +
> +static int pf1550_set_thermal_regulation_temp(struct pf1550_charger *chg,
> +					      unsigned int cells)
> +{
> +	unsigned int data;
> +
> +	switch (cells) {
> +	case 60:
> +		data = 0x0;
> +		break;
> +	case 75:
> +		data = 0x1;
> +		break;
> +	case 90:
> +		data = 0x2;
> +		break;
> +	case 105:
> +		data = 0x3;
> +		break;

From the datasheet 80, 95, 110 and 125c is supported

> +	default:
> +		return dev_err_probe(chg->dev, -EINVAL,
> +				     "Wrong value for thermal temperature\n");
> +	}
> +
> +	data <<= PF1550_CHARG_REG_THM_REG_CNFG_REGTEMP_SHIFT;
> +
> +	dev_dbg(chg->dev, "Thermal regulation loop temperature: %u (0x%x)\n",
> +		cells, data);
> +
> +	return regmap_update_bits(chg->pf1550->regmap,
> +				  PF1550_CHARG_REG_THM_REG_CNFG,
> +				  PF1550_CHARG_REG_THM_REG_CNFG_REGTEMP_MASK,
> +				  data);
> +}
> +
> +/*
> + * Sets charger registers to proper and safe default values.
> + */
> +static int pf1550_reg_init(struct pf1550_charger *chg)
> +{
> +	struct device *dev = chg->dev;
> +	unsigned int data;
> +	int ret;
> +
> +	/* Unmask charger interrupt, mask DPMI and reserved bit */
> +	ret =  regmap_write(chg->pf1550->regmap, PF1550_CHARG_REG_CHG_INT_MASK,
> +			    PF1550_CHG_INT_MASK);
> +	if (ret)
> +		return dev_err_probe(dev, ret,
> +				     "Error unmask charger interrupt\n");
> +
> +	ret = regmap_read(chg->pf1550->regmap, PF1550_CHARG_REG_VBUS_SNS,
> +			  &data);
> +	if (ret)
> +		return dev_err_probe(dev, ret, "Read charg vbus_sns error\n");

data is unused here :/

> +
> +	ret = pf1550_set_constant_volt(chg, chg->constant_volt);
> +	if (ret)
> +		return ret;
> +
> +	ret = pf1550_set_min_system_volt(chg, chg->min_system_volt);
> +	if (ret)
> +		return ret;
> +
> +	ret = pf1550_set_thermal_regulation_temp(chg,
> +						 chg->thermal_regulation_temp);
> +	if (ret)
> +		return ret;
> +
> +	/* Turn on charger */
> +	ret = regmap_write(chg->pf1550->regmap, PF1550_CHARG_REG_CHG_OPER,
> +			   PF1550_CHG_TURNON);
> +	if (ret)
> +		return dev_err_probe(dev, ret, "Error turn on charger\n");

There are 3 modes for the charger operation:
0: charger = off, linear = off
1: charger = off, linear = on
2: charger = on, linear = on

The driver is hardcoded to use no. 2.

We are using the mode 1, and setting it to 2 causes my system to boot loop.

I don't know how we should select mode, maybe it could be an option from
the devicetree or use power_supply_get_battery_info() to look for a
battery and the only select between 1 or 2, but 0 would also be a valid
option.

/Sean

On Fri, Jul 11, 2025 at 09:02:18AM +0000, Sean Nyekjaer wrote:
> > +#define PF1550_DEFAULT_THERMAL_TEMP	75
> 
> Default is 95
>
Will make changes.
> > +
> > +static int pf1550_set_thermal_regulation_temp(struct pf1550_charger *chg,
> > +					      unsigned int cells)
> > +{
> > +	unsigned int data;
> > +
> > +	switch (cells) {
> > +	case 60:
> > +		data = 0x0;
> > +		break;
> > +	case 75:
> > +		data = 0x1;
> > +		break;
> > +	case 90:
> > +		data = 0x2;
> > +		break;
> > +	case 105:
> > +		data = 0x3;
> > +		break;
> 
> From the datasheet 80, 95, 110 and 125c is supported
>
Yeah, the temp values should be as you mentioned. I'll be replacing the current
temperature range.
> > +	default:
> > +		return dev_err_probe(chg->dev, -EINVAL,
> > +				     "Wrong value for thermal temperature\n");
> > +	}
> > +
> > +	data <<= PF1550_CHARG_REG_THM_REG_CNFG_REGTEMP_SHIFT;
> > +
> > +	dev_dbg(chg->dev, "Thermal regulation loop temperature: %u (0x%x)\n",
> > +		cells, data);
> > +
> > +	return regmap_update_bits(chg->pf1550->regmap,
> > +				  PF1550_CHARG_REG_THM_REG_CNFG,
> > +				  PF1550_CHARG_REG_THM_REG_CNFG_REGTEMP_MASK,
> > +				  data);
> > +}
> > +
> > +/*
> > + * Sets charger registers to proper and safe default values.
> > + */
> > +static int pf1550_reg_init(struct pf1550_charger *chg)
> > +{
> > +	struct device *dev = chg->dev;
> > +	unsigned int data;
> > +	int ret;
> > +
> > +	/* Unmask charger interrupt, mask DPMI and reserved bit */
> > +	ret =  regmap_write(chg->pf1550->regmap, PF1550_CHARG_REG_CHG_INT_MASK,
> > +			    PF1550_CHG_INT_MASK);
> > +	if (ret)
> > +		return dev_err_probe(dev, ret,
> > +				     "Error unmask charger interrupt\n");
> > +
> > +	ret = regmap_read(chg->pf1550->regmap, PF1550_CHARG_REG_VBUS_SNS,
> > +			  &data);
> > +	if (ret)
> > +		return dev_err_probe(dev, ret, "Read charg vbus_sns error\n");
> 
> data is unused here :/
>
Yeah, that should be dropped.
> > +
> > +	ret = pf1550_set_constant_volt(chg, chg->constant_volt);
> > +	if (ret)
> > +		return ret;
> > +
> > +	ret = pf1550_set_min_system_volt(chg, chg->min_system_volt);
> > +	if (ret)
> > +		return ret;
> > +
> > +	ret = pf1550_set_thermal_regulation_temp(chg,
> > +						 chg->thermal_regulation_temp);
> > +	if (ret)
> > +		return ret;
> > +
> > +	/* Turn on charger */
> > +	ret = regmap_write(chg->pf1550->regmap, PF1550_CHARG_REG_CHG_OPER,
> > +			   PF1550_CHG_TURNON);
> > +	if (ret)
> > +		return dev_err_probe(dev, ret, "Error turn on charger\n");
> 
> There are 3 modes for the charger operation:
> 0: charger = off, linear = off
> 1: charger = off, linear = on
> 2: charger = on, linear = on
> 
> The driver is hardcoded to use no. 2.
> 
> We are using the mode 1, and setting it to 2 causes my system to boot loop.
> 
> I don't know how we should select mode, maybe it could be an option from
> the devicetree or use power_supply_get_battery_info() to look for a
> battery and the only select between 1 or 2, but 0 would also be a valid
> option.
> 
I like the latter solution of using the power_supply_get_battery_info. I think
selecting between only 1 or 2 should be fine.

Thanks,
Sam