From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Device tree for the Lenovo Thinkbook 16 G7 QOY
The Laptop is a Snapdragon X1 / X1 Plus (Purwa) based device [1].
Supported features:
- USB type-c and type-a ports
- Keyboard
- Touchpad (all that are described in the dsdt)
- Touchscreen (described in the dsdt, no known SKUss)
- Display including PWM backlight control
- PCIe devices
- nvme
- SDHC card reader
- ath12k WCN7850 Wifi and Bluetooth
- ADSP and CDSP
- GPIO keys (Lid switch)
- Sound via internal speakers / DMIC / USB / headphone jack
- DP Altmode with 2 lanes (as all of these still do)
- Integrated fingerprint reader (FPC)
- Integrated UVC camera
- X1-45 GPU
Not supported yet:
- HDMI port.
- EC and some fn hotkeys.
Limited support yet:
- SDHC card reader is based on the on-chip sdhc_2 controller, but the driver from
the Snapdragon Dev Kit is only a partial match. It can do normal slow sd cards,
but not UHS-I (SD104) and UHS-II.
This work was done without any schematics or non-public knowledge of the device.
So, it is based on the existing x1e device trees, dsdt analysis, using HWInfo
ARM64, and pure guesswork. It has been confirmed, however, that the device really
has 4 NXP PTN3222 eUSB2 repeaters, one of which doesn't have a reset GPIO (eusb5
@43).
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Co-developed by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
---
arch/arm64/boot/dts/qcom/Makefile | 2 +
arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi | 2 +-
.../boot/dts/qcom/x1p42100-lenovo-thinkbook-16.dts | 1657 ++++++++++++++++++++
3 files changed, 1660 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 4bfa926b6a0850c3c459bcba28129c559d50a7cf..6b1d71daff5a778237c5e3706aaea8e29dafa001 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -333,3 +333,5 @@ x1p42100-asus-zenbook-a14-el2-dtbs := x1p42100-asus-zenbook-a14.dtb x1-el2.dtbo
dtb-$(CONFIG_ARCH_QCOM) += x1p42100-asus-zenbook-a14.dtb x1p42100-asus-zenbook-a14-el2.dtb
x1p42100-crd-el2-dtbs := x1p42100-crd.dtb x1-el2.dtbo
dtb-$(CONFIG_ARCH_QCOM) += x1p42100-crd.dtb x1p42100-crd-el2.dtb
+x1p42100-lenovo-thinkbook-16-el2-dtbs := x1p42100-lenovo-thinkbook-16.dtb x1-el2.dtbo
+dtb-$(CONFIG_ARCH_QCOM) += x1p42100-lenovo-thinkbook-16.dtb x1p42100-lenovo-thinkbook-16-el2.dtb
diff --git a/arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi b/arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi
index e3888bc143a0aaae23c92d400d48ea94423e0366..378635f7cb0bfe37cf10644a16bd8b3cca447f3c 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi
@@ -170,7 +170,7 @@ trip1 {
};
};
- pm8010-thermal {
+ pm8010_thermal: pm8010-thermal {
polling-delay-passive = <100>;
thermal-sensors = <&pm8010_temp_alarm>;
diff --git a/arch/arm64/boot/dts/qcom/x1p42100-lenovo-thinkbook-16.dts b/arch/arm64/boot/dts/qcom/x1p42100-lenovo-thinkbook-16.dts
new file mode 100644
index 0000000000000000000000000000000000000000..d117e1b4848c13e4a8f5a342d09fe8b9878889cd
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/x1p42100-lenovo-thinkbook-16.dts
@@ -0,0 +1,1657 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2024, Linaro Limited
+ * Copyright (c) 2025, Jens Glathe
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "x1p42100.dtsi"
+#include "x1e80100-pmics.dtsi"
+
+/delete-node/ &pmc8380_6;
+/delete-node/ &pmc8380_6_thermal;
+/delete-node/ &pm8010;
+/delete-node/ &pm8010_thermal;
+
+/ {
+ model = "Lenovo ThinkBook 16 Gen 7 QOY";
+ compatible = "lenovo,thinkbook-16", "qcom,x1p42100";
+ chassis-type = "laptop";
+
+ aliases {
+ serial0 = &uart21;
+ serial1 = &uart14;
+ };
+
+ wcd938x: audio-codec {
+ compatible = "qcom,wcd9385-codec";
+
+ pinctrl-0 = <&wcd_default>;
+ pinctrl-names = "default";
+
+ qcom,micbias1-microvolt = <1800000>;
+ qcom,micbias2-microvolt = <1800000>;
+ qcom,micbias3-microvolt = <1800000>;
+ qcom,micbias4-microvolt = <1800000>;
+ qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+ qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+ qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+ qcom,rx-device = <&wcd_rx>;
+ qcom,tx-device = <&wcd_tx>;
+
+ reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>;
+
+ vdd-buck-supply = <&vreg_l15b_1p8>;
+ vdd-rxtx-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l15b_1p8>;
+ vdd-mic-bias-supply = <&vreg_bob1>;
+
+ #sound-dai-cells = <1>;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pm8550_pwm 3 500000>;
+
+ power-supply = <&vreg_edp_bl>;
+ };
+
+ /*
+ * This is an odd one. The camera is physically behind the eusb9 repeater (confirmed) but
+ * if it is placed below the usb_2_dwc3 node, it will be switched of after ~30 seconds.
+ * The reason seems to be that the dwc3 driver does not probe for child nodes when in
+ * host-only mode. But that's the default setting for the xhci controllers due to issues
+ * when in OTG mode. https://lore.kernel.org/all/20241210111444.26240-1-johan+linaro@kernel.org/
+ * The whole reason it is described in the dt (as an USB device) is its requirement for
+ * that additional regulator, and to get power management to switch it off when suspended.
+ * Defining it stand-alone does work.
+ */
+ camera {
+ compatible = "usb5986,1198";
+
+ vdd-supply = <&vreg_cam_5p0>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-0 = <&hall_int_n_default>;
+ pinctrl-names = "default";
+
+ switch-lid {
+ gpios = <&tlmm 92 GPIO_ACTIVE_LOW>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_LID>;
+ wakeup-source;
+ wakeup-event-action = <EV_ACT_DEASSERTED>;
+ };
+ };
+
+ pmic-glink {
+ compatible = "qcom,x1e80100-pmic-glink",
+ "qcom,sm8550-pmic-glink",
+ "qcom,pmic-glink";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
+ <&tlmm 123 GPIO_ACTIVE_HIGH>;
+
+ /* Display-adjacent port */
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ power-role = "dual";
+ data-role = "host";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_ss0_hs_in: endpoint {
+ remote-endpoint = <&usb_1_ss0_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss0_ss_in: endpoint {
+ remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_ss0_sbu: endpoint {
+ remote-endpoint = <&usb_1_ss0_sbu_mux>;
+ };
+ };
+ };
+ };
+
+ /* User-adjacent port */
+ connector@1 {
+ compatible = "usb-c-connector";
+ reg = <1>;
+ power-role = "dual";
+ data-role = "host";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_ss1_hs_in: endpoint {
+ remote-endpoint = <&usb_1_ss1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss1_ss_in: endpoint {
+ remote-endpoint = <&usb_1_ss1_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_ss1_sbu: endpoint {
+ remote-endpoint = <&usb_1_ss1_sbu_mux>;
+ };
+ };
+ };
+ };
+ };
+
+ sound {
+ compatible = "qcom,x1e80100-sndcard";
+ model = "X1E80100-LENOVO-ThinkBook-16";
+ audio-routing = "SpkrLeft IN", "WSA WSA_SPK1 OUT",
+ "SpkrRight IN", "WSA WSA_SPK2 OUT",
+ "IN1_HPHL", "HPHL_OUT",
+ "IN2_HPHR", "HPHR_OUT",
+ "AMIC2", "MIC BIAS2",
+ "VA DMIC0", "MIC BIAS3",
+ "VA DMIC1", "MIC BIAS3",
+ "VA DMIC2", "MIC BIAS1",
+ "VA DMIC3", "MIC BIAS1",
+ "VA DMIC0", "VA MIC BIAS3",
+ "VA DMIC1", "VA MIC BIAS3",
+ "VA DMIC2", "VA MIC BIAS1",
+ "VA DMIC3", "VA MIC BIAS1",
+ "TX SWR_INPUT1", "ADC2_OUTPUT";
+
+ wcd-playback-dai-link {
+ link-name = "WCD Playback";
+
+ cpu {
+ sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+ };
+
+ codec {
+ sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ wcd-capture-dai-link {
+ link-name = "WCD Capture";
+
+ cpu {
+ sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+ };
+
+ codec {
+ sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ wsa-dai-link {
+ link-name = "WSA Playback";
+
+ codec {
+ sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&lpass_wsamacro 0>;
+ };
+
+ cpu {
+ sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ va-dai-link {
+ link-name = "VA Capture";
+
+ codec {
+ sound-dai = <&lpass_vamacro 0>;
+ };
+
+ cpu {
+ sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+ };
+
+ usb-1-ss0-sbu-mux {
+ compatible = "onnn,fsusb42", "gpio-sbu-mux";
+
+ enable-gpios = <&tlmm 167 GPIO_ACTIVE_LOW>;
+ select-gpios = <&tlmm 168 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&usb_1_ss0_sbu_default>;
+ pinctrl-names = "default";
+
+ mode-switch;
+ orientation-switch;
+
+ port {
+ usb_1_ss0_sbu_mux: endpoint {
+ remote-endpoint = <&pmic_glink_ss0_sbu>;
+ };
+ };
+ };
+
+ usb-1-ss1-sbu-mux {
+ compatible = "onnn,fsusb42", "gpio-sbu-mux";
+
+ enable-gpios = <&tlmm 178 GPIO_ACTIVE_LOW>;
+ select-gpios = <&tlmm 179 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&usb_1_ss1_sbu_default>;
+ pinctrl-names = "default";
+
+ mode-switch;
+ orientation-switch;
+
+ port {
+ usb_1_ss1_sbu_mux: endpoint {
+ remote-endpoint = <&pmic_glink_ss1_sbu>;
+ };
+ };
+ };
+
+ vreg_cam_5p0: regulator-cam-5p0 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_CAM_5P0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ gpio = <&tlmm 44 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&cam_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_edp_3p3: regulator-edp-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_EDP_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&edp_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_edp_bl: regulator-edp-bl {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VBL9";
+ regulator-min-microvolt = <3600000>;
+ regulator-max-microvolt = <3600000>;
+
+ gpio = <&pmc8380_3_gpios 10 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&edp_bl_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_misc_3p3: regulator-misc-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_MISC_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pm8550ve_8_gpios 6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&misc_3p3_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vreg_nvme: regulator-nvme {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_NVME_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&nvme_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_wcn_0p95: regulator-wcn-0p95 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WCN_0P95";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <950000>;
+
+ vin-supply = <&vreg_wcn_3p3>;
+ };
+
+ vreg_wcn_1p9: regulator-wcn-1p9 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WCN_1P9";
+ regulator-min-microvolt = <1900000>;
+ regulator-max-microvolt = <1900000>;
+
+ vin-supply = <&vreg_wcn_3p3>;
+ };
+
+ vreg_wcn_3p3: regulator-wcn-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WCN_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&wcn_sw_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vph_pwr: regulator-vph-pwr {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ wcn7850-pmu {
+ compatible = "qcom,wcn7850-pmu";
+
+ vdd-supply = <&vreg_wcn_0p95>;
+ vddio-supply = <&vreg_l15b_1p8>;
+ vddaon-supply = <&vreg_wcn_0p95>;
+ vdddig-supply = <&vreg_wcn_0p95>;
+ vddrfa1p2-supply = <&vreg_wcn_1p9>;
+ vddrfa1p8-supply = <&vreg_wcn_1p9>;
+
+ wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
+ bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&wcn_wlan_en>;
+ pinctrl-1 = <&wcn_bt_en>;
+ pinctrl-names = "default";
+
+ regulators {
+ vreg_pmu_rfa_cmn: ldo0 {
+ regulator-name = "vreg_pmu_rfa_cmn";
+ };
+
+ vreg_pmu_aon_0p59: ldo1 {
+ regulator-name = "vreg_pmu_aon_0p59";
+ };
+
+ vreg_pmu_wlcx_0p8: ldo2 {
+ regulator-name = "vreg_pmu_wlcx_0p8";
+ };
+
+ vreg_pmu_wlmx_0p85: ldo3 {
+ regulator-name = "vreg_pmu_wlmx_0p85";
+ };
+
+ vreg_pmu_btcmx_0p85: ldo4 {
+ regulator-name = "vreg_pmu_btcmx_0p85";
+ };
+
+ vreg_pmu_rfa_0p8: ldo5 {
+ regulator-name = "vreg_pmu_rfa_0p8";
+ };
+
+ vreg_pmu_rfa_1p2: ldo6 {
+ regulator-name = "vreg_pmu_rfa_1p2";
+ };
+
+ vreg_pmu_rfa_1p8: ldo7 {
+ regulator-name = "vreg_pmu_rfa_1p8";
+ };
+
+ vreg_pmu_pcie_0p9: ldo8 {
+ regulator-name = "vreg_pmu_pcie_0p9";
+ };
+
+ vreg_pmu_pcie_1p8: ldo9 {
+ regulator-name = "vreg_pmu_pcie_1p8";
+ };
+ };
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pm8550-rpmh-regulators";
+ qcom,pmic-id = "b";
+
+ vdd-bob1-supply = <&vph_pwr>;
+ vdd-bob2-supply = <&vph_pwr>;
+ vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>;
+ vdd-l2-l13-l14-supply = <&vreg_bob1>;
+ vdd-l5-l16-supply = <&vreg_bob1>;
+ vdd-l6-l7-supply = <&vreg_bob2>;
+ vdd-l8-l9-supply = <&vreg_bob1>;
+ vdd-l12-supply = <&vreg_s5j_1p2>;
+ vdd-l15-supply = <&vreg_s4c_1p8>;
+ vdd-l17-supply = <&vreg_bob2>;
+
+ vreg_bob1: bob1 {
+ regulator-name = "vreg_bob1";
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_bob2: bob2 {
+ regulator-name = "vreg_bob2";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1b_1p8: ldo1 {
+ regulator-name = "vreg_l1b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2b_3p0: ldo2 {
+ regulator-name = "vreg_l2b_3p0";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4b_1p8: ldo4 {
+ regulator-name = "vreg_l4b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5b_3p0: ldo5 {
+ regulator-name = "vreg_l5b_3p0";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6b_1p8: ldo6 {
+ regulator-name = "vreg_l6b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7b_2p8: ldo7 {
+ regulator-name = "vreg_l7b_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8b_3p0: ldo8 {
+ regulator-name = "vreg_l8b_3p0";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9b_2p9: ldo9 {
+ regulator-name = "vreg_l9b_2p9";
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10b_1p8: ldo10 {
+ regulator-name = "vreg_l10b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12b_1p2: ldo12 {
+ regulator-name = "vreg_l12b_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ };
+
+ vreg_l13b_3p0: ldo13 {
+ regulator-name = "vreg_l13b_3p0";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l14b_3p0: ldo14 {
+ regulator-name = "vreg_l14b_3p0";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l15b_1p8: ldo15 {
+ regulator-name = "vreg_l15b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ };
+
+ vreg_l16b_2p9: ldo16 {
+ regulator-name = "vreg_l16b_2p9";
+ regulator-min-microvolt = <2912000>;
+ regulator-max-microvolt = <2912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l17b_2p5: ldo17 {
+ regulator-name = "vreg_l17b_2p5";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pm8550ve-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vdd-l1-supply = <&vreg_s5j_1p2>;
+ vdd-l2-supply = <&vreg_s1f_0p7>;
+ vdd-l3-supply = <&vreg_s1f_0p7>;
+ vdd-s4-supply = <&vph_pwr>;
+
+ vreg_s4c_1p8: smps4 {
+ regulator-name = "vreg_s4c_1p8";
+ regulator-min-microvolt = <1856000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1c_1p2: ldo1 {
+ regulator-name = "vreg_l1c_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2c_0p8: ldo2 {
+ regulator-name = "vreg_l2c_0p8";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3c_0p8: ldo3 {
+ regulator-name = "vreg_l3c_0p8";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-2 {
+ compatible = "qcom,pmc8380-rpmh-regulators";
+ qcom,pmic-id = "d";
+
+ vdd-l1-supply = <&vreg_s1f_0p7>;
+ vdd-l2-supply = <&vreg_s1f_0p7>;
+ vdd-l3-supply = <&vreg_s4c_1p8>;
+ vdd-s1-supply = <&vph_pwr>;
+
+ vreg_l1d_0p8: ldo1 {
+ regulator-name = "vreg_l1d_0p8";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2d_0p9: ldo2 {
+ regulator-name = "vreg_l2d_0p9";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3d_1p8: ldo3 {
+ regulator-name = "vreg_l3d_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-3 {
+ compatible = "qcom,pmc8380-rpmh-regulators";
+ qcom,pmic-id = "e";
+
+ vdd-l2-supply = <&vreg_s1f_0p7>;
+ vdd-l3-supply = <&vreg_s5j_1p2>;
+
+ vreg_l2e_0p8: ldo2 {
+ regulator-name = "vreg_l2e_0p8";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3e_1p2: ldo3 {
+ regulator-name = "vreg_l3e_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-4 {
+ compatible = "qcom,pmc8380-rpmh-regulators";
+ qcom,pmic-id = "f";
+
+ vdd-l1-supply = <&vreg_s5j_1p2>;
+ vdd-l2-supply = <&vreg_s5j_1p2>;
+ vdd-l3-supply = <&vreg_s5j_1p2>;
+ vdd-s1-supply = <&vph_pwr>;
+
+ vreg_s1f_0p7: smps1 {
+ regulator-name = "vreg_s1f_0p7";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1f_1p0: ldo1 {
+ regulator-name = "vreg_l1f_1p0";
+ regulator-min-microvolt = <1024000>;
+ regulator-max-microvolt = <1024000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2f_1p0: ldo2 {
+ regulator-name = "vreg_l2f_1p0";
+ regulator-min-microvolt = <1024000>;
+ regulator-max-microvolt = <1024000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3f_1p0: ldo3 {
+ regulator-name = "vreg_l3f_1p0";
+ regulator-min-microvolt = <1024000>;
+ regulator-max-microvolt = <1024000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-6 {
+ compatible = "qcom,pm8550ve-rpmh-regulators";
+ qcom,pmic-id = "i";
+
+ vdd-l1-supply = <&vreg_s4c_1p8>;
+ vdd-l2-supply = <&vreg_s5j_1p2>;
+ vdd-l3-supply = <&vreg_s1f_0p7>;
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+
+ vreg_l1i_1p8: ldo1 {
+ regulator-name = "vreg_l1i_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ };
+
+ vreg_l2i_1p2: ldo2 {
+ regulator-name = "vreg_l2i_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3i_0p8: ldo3 {
+ regulator-name = "vreg_l3i_0p8";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s1i_0p9: smps1 {
+ regulator-name = "vreg_s1i_0p9";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s2i_1p0: smps2 {
+ regulator-name = "vreg_s2i_1p0";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-7 {
+ compatible = "qcom,pm8550ve-rpmh-regulators";
+ qcom,pmic-id = "j";
+
+ vdd-l1-supply = <&vreg_s1f_0p7>;
+ vdd-l2-supply = <&vreg_s5j_1p2>;
+ vdd-l3-supply = <&vreg_s1f_0p7>;
+ vdd-s5-supply = <&vph_pwr>;
+
+ vreg_s5j_1p2: smps5 {
+ regulator-name = "vreg_s5j_1p2";
+ regulator-min-microvolt = <1256000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1j_0p8: ldo1 {
+ regulator-name = "vreg_l1j_0p8";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2j_1p2: ldo2 {
+ regulator-name = "vreg_l2j_1p2";
+ regulator-min-microvolt = <1256000>;
+ regulator-max-microvolt = <1256000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3j_0p8: ldo3 {
+ regulator-name = "vreg_l3j_0p8";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&gpu {
+ status = "okay";
+};
+
+&gpu_zap_shader {
+ firmware-name = "qcom/x1p42100/LENOVO/21NH/qcdxkmsucpurwa.mbn";
+};
+
+&i2c2 {
+ clock-frequency = <400000>;
+
+ pinctrl-0 = <&qup_i2c2_data_clk>, <&tpad_default>, <&kybd_default>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ /* ELAN06FA */
+ touchpad@15 {
+ compatible = "hid-over-i2c";
+ reg = <0x15>;
+
+ hid-descr-addr = <0x1>;
+ interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+ vdd-supply = <&vreg_misc_3p3>;
+ vddl-supply = <&vreg_l12b_1p2>;
+
+ wakeup-source;
+ };
+
+ /* CIRQ1080 or SYNA2BA6 */
+ touchpad@2c {
+ compatible = "hid-over-i2c";
+ reg = <0x2c>;
+
+ hid-descr-addr = <0x20>;
+ interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+ vdd-supply = <&vreg_misc_3p3>;
+ vddl-supply = <&vreg_l12b_1p2>;
+
+ wakeup-source;
+ };
+
+ /* FTCS0038 */
+ touchpad@38 {
+ compatible = "hid-over-i2c";
+ reg = <0x38>;
+
+ hid-descr-addr = <0x1>;
+ interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+ vdd-supply = <&vreg_misc_3p3>;
+ vddl-supply = <&vreg_l12b_1p2>;
+
+ wakeup-source;
+ };
+
+ keyboard@3a {
+ compatible = "hid-over-i2c";
+ reg = <0x3a>;
+
+ hid-descr-addr = <0x1>;
+ interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
+
+ vdd-supply = <&vreg_misc_3p3>;
+ vddl-supply = <&vreg_l12b_1p2>;
+
+ wakeup-source;
+ };
+
+ /* GXTP5100 */
+ touchpad@5d {
+ compatible = "hid-over-i2c";
+ reg = <0x5d>;
+
+ hid-descr-addr = <0x1>;
+ interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+ vdd-supply = <&vreg_misc_3p3>;
+ vddl-supply = <&vreg_l12b_1p2>;
+
+ wakeup-source;
+ };
+};
+
+&i2c5 {
+ clock-frequency = <400000>;
+
+ status = "okay";
+
+ eusb5_repeater: redriver@43 {
+ compatible = "nxp,ptn3222";
+ reg = <0x43>;
+ #phy-cells = <0>;
+
+ vdd3v3-supply = <&vreg_l13b_3p0>;
+ vdd1v8-supply = <&vreg_l4b_1p8>;
+ };
+
+ eusb3_repeater: redriver@47 {
+ compatible = "nxp,ptn3222";
+ reg = <0x47>;
+ #phy-cells = <0>;
+
+ vdd3v3-supply = <&vreg_l13b_3p0>;
+ vdd1v8-supply = <&vreg_l4b_1p8>;
+
+ reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&eusb3_reset_n>;
+ pinctrl-names = "default";
+ };
+
+ eusb9_repeater: redriver@4b {
+ compatible = "nxp,ptn3222";
+ reg = <0x4b>;
+ #phy-cells = <0>;
+
+ vdd3v3-supply = <&vreg_l13b_3p0>;
+ vdd1v8-supply = <&vreg_l4b_1p8>;
+
+ reset-gpios = <&tlmm 7 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&eusb9_reset_n>;
+ pinctrl-names = "default";
+ };
+
+ eusb6_repeater: redriver@4f {
+ compatible = "nxp,ptn3222";
+ reg = <0x4f>;
+ #phy-cells = <0>;
+
+ vdd3v3-supply = <&vreg_l13b_3p0>;
+ vdd1v8-supply = <&vreg_l4b_1p8>;
+
+ reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&eusb6_reset_n>;
+ pinctrl-names = "default";
+ };
+};
+
+&i2c8 {
+ clock-frequency = <400000>;
+
+ status = "okay";
+
+ /* ILIT2911 or GTCH1563 */
+ touchscreen@10 {
+ compatible = "hid-over-i2c";
+ reg = <0x10>;
+
+ hid-descr-addr = <0x1>;
+ interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;
+
+ vdd-supply = <&vreg_misc_3p3>;
+ vddl-supply = <&vreg_l15b_1p8>;
+
+ pinctrl-0 = <&ts0_default>;
+ pinctrl-names = "default";
+ };
+};
+
+&lpass_tlmm {
+ spkr_01_sd_n_active: spkr-01-sd-n-active-state {
+ pins = "gpio12";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+};
+
+&lpass_vamacro {
+ pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
+ pinctrl-names = "default";
+
+ vdd-micb-supply = <&vreg_l1b_1p8>;
+ qcom,dmic-sample-rate = <4800000>;
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dp0 {
+ status = "okay";
+};
+
+&mdss_dp0_out {
+ data-lanes = <0 1 2 3>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp1 {
+ status = "okay";
+};
+
+&mdss_dp1_out {
+ data-lanes = <0 1 2 3>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp2 {
+ status = "okay";
+};
+
+&mdss_dp2_out {
+ data-lanes = <0 1 2 3>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp2_phy {
+// vdda-phy-supply = <&vreg_l3b>;
+// vdda-pll-supply = <&vreg_l6b>;
+
+ status = "okay";
+};
+
+&mdss_dp3 {
+ /delete-property/ #sound-dai-cells;
+
+ status = "okay";
+
+ aux-bus {
+ panel {
+ compatible = "edp-panel";
+
+ backlight = <&backlight>;
+
+ enable-gpios = <&pmc8380_3_gpios 4 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&edp_bl_en>;
+ pinctrl-names = "default";
+
+ power-supply = <&vreg_edp_3p3>;
+
+ port {
+ edp_panel_in: endpoint {
+ remote-endpoint = <&mdss_dp3_out>;
+ };
+ };
+ };
+ };
+
+ ports {
+ port@1 {
+ reg = <1>;
+
+ mdss_dp3_out: endpoint {
+ data-lanes = <0 1 2 3>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+ remote-endpoint = <&edp_panel_in>;
+ };
+ };
+ };
+};
+
+&mdss_dp3_phy {
+ vdda-phy-supply = <&vreg_l3j_0p8>;
+ vdda-pll-supply = <&vreg_l2j_1p2>;
+
+ status = "okay";
+};
+
+&pcie4 {
+ perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&pcie4_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie4_phy {
+ vdda-phy-supply = <&vreg_l3i_0p8>;
+ vdda-pll-supply = <&vreg_l3e_1p2>;
+
+ status = "okay";
+};
+
+&pcie4_port0 {
+ wifi@0 {
+ compatible = "pci17cb,1107";
+ reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+ vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+ vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+ };
+};
+
+&pcie6a {
+ perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
+
+ vddpe-3v3-supply = <&vreg_nvme>;
+
+ pinctrl-0 = <&pcie6a_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie6a_phy {
+ vdda-phy-supply = <&vreg_l1d_0p8>;
+ vdda-pll-supply = <&vreg_l2j_1p2>;
+
+ status = "okay";
+};
+
+&pm8550_pwm {
+ status = "okay";
+};
+
+&pm8550ve_8_gpios {
+ misc_3p3_reg_en: misc-3p3-reg-en-state {
+ pins = "gpio6";
+ function = "normal";
+ bias-disable;
+ input-disable;
+ output-enable;
+ drive-push-pull;
+ power-source = <1>; /* 1.8 V */
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ };
+};
+
+&pmc8380_3_gpios {
+ edp_bl_en: edp-bl-en-state {
+ pins = "gpio4";
+ function = "normal";
+ power-source = <1>; /* 1.8V */
+ input-disable;
+ output-enable;
+ };
+
+ edp_bl_reg_en: edp-bl-reg-en-state {
+ pins = "gpio10";
+ function = "normal";
+ };
+};
+
+&qupv3_0 {
+ status = "okay";
+};
+
+&qupv3_1 {
+ status = "okay";
+};
+
+&qupv3_2 {
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/x1p42100/LENOVO/21NH/qcadsp8380.mbn",
+ "qcom/x1p42100/LENOVO/21NH/adsp_dtbs.elf";
+
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ firmware-name = "qcom/x1p42100/LENOVO/21NH/qccdsp8380.mbn",
+ "qcom/x1p42100/LENOVO/21NH/cdsp_dtbs.elf";
+
+ status = "okay";
+};
+
+&sdhc_2 {
+ cd-gpios = <&tlmm 71 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
+ pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
+ pinctrl-names = "default", "sleep";
+ vmmc-supply = <&vreg_l9b_2p9>;
+ vqmmc-supply = <&vreg_l6b_1p8>;
+// bus-width = <4>;
+// no-sdio;
+// no-mmc;
+ status = "okay";
+};
+
+&smb2360_0 {
+ status = "okay";
+};
+
+&smb2360_0_eusb2_repeater {
+ vdd18-supply = <&vreg_l3d_1p8>;
+ vdd3-supply = <&vreg_l2b_3p0>;
+};
+
+&smb2360_1 {
+ status = "okay";
+};
+
+&smb2360_1_eusb2_repeater {
+ vdd18-supply = <&vreg_l3d_1p8>;
+ vdd3-supply = <&vreg_l14b_3p0>;
+};
+
+&swr0 {
+ status = "okay";
+
+ pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>;
+ pinctrl-names = "default";
+
+ /* WSA8845, Left Speaker */
+ left_spkr: speaker@0,0 {
+ compatible = "sdw20217020400";
+ reg = <0 0>;
+ reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SpkrLeft";
+ vdd-1p8-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l12b_1p2>;
+ qcom,port-mapping = <1 2 3 7 10 13>;
+ };
+
+ /* WSA8845, Right Speaker */
+ right_spkr: speaker@0,1 {
+ compatible = "sdw20217020400";
+ reg = <0 1>;
+ reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SpkrRight";
+ vdd-1p8-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l12b_1p2>;
+ qcom,port-mapping = <4 5 6 7 11 13>;
+ };
+};
+
+&swr1 {
+ status = "okay";
+
+ /* WCD9385 RX */
+ wcd_rx: codec@0,4 {
+ compatible = "sdw20217010d00";
+ reg = <0 4>;
+ qcom,rx-port-mapping = <1 2 3 4 5>;
+ };
+};
+
+&swr2 {
+ status = "okay";
+
+ /* WCD9385 TX */
+ wcd_tx: codec@0,3 {
+ compatible = "sdw20217010d00";
+ reg = <0 3>;
+ qcom,tx-port-mapping = <2 2 3 4>;
+ };
+};
+
+&tlmm {
+ gpio-reserved-ranges = <34 2>, /* Unused */
+ <72 2>, /* Secure EC I2C connection (?) */
+ <238 1>; /* UFS Reset */
+
+ cam_reg_en: cam-reg-en-state {
+ pins = "gpio44";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ eusb3_reset_n: eusb3-reset-n-state {
+ pins = "gpio6";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+
+ eusb6_reset_n: eusb6-reset-n-state {
+ pins = "gpio184";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+
+ eusb9_reset_n: eusb9-reset-n-state {
+ pins = "gpio7";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+
+ edp_reg_en: edp-reg-en-state {
+ pins = "gpio70";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ hall_int_n_default: hall-int-n-state {
+ pins = "gpio92";
+ function = "gpio";
+ bias-disable;
+ };
+
+ kybd_default: kybd-default-state {
+ pins = "gpio67";
+ function = "gpio";
+ bias-disable;
+ };
+
+ nvme_reg_en: nvme-reg-en-state {
+ pins = "gpio18";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ pcie4_default: pcie4-default-state {
+ clkreq-n-pins {
+ pins = "gpio147";
+ function = "pcie4_clk";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio146";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wake-n-pins {
+ pins = "gpio148";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ pcie6a_default: pcie6a-default-state {
+ clkreq-n-pins {
+ pins = "gpio153";
+ function = "pcie6a_clk";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio152";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wake-n-pins {
+ pins = "gpio154";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ sdc2_card_det_n: sdc2-card-det-state {
+ pins = "gpio71";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ tpad_default: tpad-default-state {
+ pins = "gpio3";
+ function = "gpio";
+ bias-pull-up;
+ };
+
+ ts0_default: ts0-default-state {
+ int-n-pins {
+ pins = "gpio51";
+ function = "gpio";
+ bias-disable;
+ };
+
+ reset-n-pins {
+ pins = "gpio48";
+ function = "gpio";
+ output-high;
+ drive-strength = <16>;
+ };
+ };
+
+ usb_1_ss0_sbu_default: usb-1-ss0-sbu-state {
+ oe-n-pins {
+ pins = "gpio167";
+ function = "gpio";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ sel-pins {
+ pins = "gpio168";
+ function = "gpio";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ };
+
+ usb_1_ss1_sbu_default: usb-1-ss1-sbu-state {
+ oe-n-pins {
+ pins = "gpio178";
+ function = "gpio";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ sel-pins {
+ pins = "gpio179";
+ function = "gpio";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+ };
+
+ wcd_default: wcd-reset-n-active-state {
+ pins = "gpio191";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+
+ wcn_bt_en: wcn-bt-en-state {
+ pins = "gpio116";
+ function = "gpio";
+ drive-strength = <16>;
+ output-low;
+ bias-pull-down;
+ };
+
+ wcn_sw_en: wcn-sw-en-state {
+ pins = "gpio214";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ wcn_wlan_en: wcn-wlan-en-state {
+ pins = "gpio117";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+};
+
+&uart14 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn7850-bt";
+ max-speed = <3200000>;
+
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+ };
+};
+
+&usb_1_ss0_hsphy {
+ vdd-supply = <&vreg_l3j_0p8>;
+ vdda12-supply = <&vreg_l2j_1p2>;
+
+ phys = <&smb2360_0_eusb2_repeater>;
+
+ status = "okay";
+};
+
+&usb_1_ss0_qmpphy {
+ vdda-phy-supply = <&vreg_l3e_1p2>;
+ vdda-pll-supply = <&vreg_l1j_0p8>;
+
+ status = "okay";
+};
+
+&usb_1_ss0 {
+ status = "okay";
+};
+
+&usb_1_ss0_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_1_ss0_dwc3_hs {
+ remote-endpoint = <&pmic_glink_ss0_hs_in>;
+};
+
+&usb_1_ss0_qmpphy_out {
+ remote-endpoint = <&pmic_glink_ss0_ss_in>;
+};
+
+&usb_1_ss1_hsphy {
+ vdd-supply = <&vreg_l3j_0p8>;
+ vdda12-supply = <&vreg_l2j_1p2>;
+
+ phys = <&smb2360_1_eusb2_repeater>;
+
+ status = "okay";
+};
+
+&usb_1_ss1_qmpphy {
+ vdda-phy-supply = <&vreg_l2j_1p2>;
+ vdda-pll-supply = <&vreg_l2d_0p9>;
+
+ status = "okay";
+};
+
+&usb_1_ss1 {
+ status = "okay";
+};
+
+&usb_1_ss1_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_1_ss1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_ss1_hs_in>;
+};
+
+&usb_1_ss1_qmpphy_out {
+ remote-endpoint = <&pmic_glink_ss1_ss_in>;
+};
+
+&usb_1_ss2 {
+ status = "okay";
+};
+
+&usb_1_ss2_dwc3 {
+ dr_mode = "host";
+ maximum-speed = "high-speed";
+ phys = <&usb_1_ss2_hsphy>;
+ phy-names = "usb2-phy";
+};
+
+&usb_1_ss2_hsphy {
+ vdd-supply = <&vreg_l3j_0p8>;
+ vdda12-supply = <&vreg_l2j_1p2>;
+
+ phys = <&eusb5_repeater>;
+
+ status = "okay";
+};
+
+&usb_2 {
+ status = "okay";
+};
+
+&usb_2_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_2_hsphy {
+ vdd-supply = <&vreg_l2e_0p8>;
+ vdda12-supply = <&vreg_l3e_1p2>;
+
+ phys = <&eusb9_repeater>;
+
+ status = "okay";
+};
+
+&usb_mp {
+ status = "okay";
+};
+
+&usb_mp_hsphy0 {
+ vdd-supply = <&vreg_l2e_0p8>;
+ vdda12-supply = <&vreg_l3e_1p2>;
+
+ phys = <&eusb6_repeater>;
+
+ status = "okay";
+};
+
+&usb_mp_qmpphy0 {
+ vdda-phy-supply = <&vreg_l3e_1p2>;
+ vdda-pll-supply = <&vreg_l3c_0p8>;
+
+ status = "okay";
+};
+
+&usb_mp_hsphy1 {
+ vdd-supply = <&vreg_l2e_0p8>;
+ vdda12-supply = <&vreg_l3e_1p2>;
+
+ phys = <&eusb3_repeater>;
+
+ status = "okay";
+};
+
+&usb_mp_qmpphy1 {
+ vdda-phy-supply = <&vreg_l3e_1p2>;
+ vdda-pll-supply = <&vreg_l3c_0p8>;
+
+ status = "okay";
+};
--
2.48.1On 7/1/25 7:02 PM, Jens Glathe via B4 Relay wrote:
> From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
>
> Device tree for the Lenovo Thinkbook 16 G7 QOY
>
> The Laptop is a Snapdragon X1 / X1 Plus (Purwa) based device [1].
>
> Supported features:
>
> - USB type-c and type-a ports
> - Keyboard
> - Touchpad (all that are described in the dsdt)
> - Touchscreen (described in the dsdt, no known SKUss)
> - Display including PWM backlight control
> - PCIe devices
> - nvme
> - SDHC card reader
> - ath12k WCN7850 Wifi and Bluetooth
> - ADSP and CDSP
> - GPIO keys (Lid switch)
> - Sound via internal speakers / DMIC / USB / headphone jack
> - DP Altmode with 2 lanes (as all of these still do)
> - Integrated fingerprint reader (FPC)
> - Integrated UVC camera
> - X1-45 GPU
>
> Not supported yet:
>
> - HDMI port.
> - EC and some fn hotkeys.
>
> Limited support yet:
>
> - SDHC card reader is based on the on-chip sdhc_2 controller, but the driver from
> the Snapdragon Dev Kit is only a partial match. It can do normal slow sd cards,
> but not UHS-I (SD104) and UHS-II.
>
> This work was done without any schematics or non-public knowledge of the device.
> So, it is based on the existing x1e device trees, dsdt analysis, using HWInfo
> ARM64, and pure guesswork. It has been confirmed, however, that the device really
> has 4 NXP PTN3222 eUSB2 repeaters, one of which doesn't have a reset GPIO (eusb5
> @43).
>
> Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
> Co-developed by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 2 +
> arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi | 2 +-
> .../boot/dts/qcom/x1p42100-lenovo-thinkbook-16.dts | 1657 ++++++++++++++++++++
> 3 files changed, 1660 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 4bfa926b6a0850c3c459bcba28129c559d50a7cf..6b1d71daff5a778237c5e3706aaea8e29dafa001 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -333,3 +333,5 @@ x1p42100-asus-zenbook-a14-el2-dtbs := x1p42100-asus-zenbook-a14.dtb x1-el2.dtbo
> dtb-$(CONFIG_ARCH_QCOM) += x1p42100-asus-zenbook-a14.dtb x1p42100-asus-zenbook-a14-el2.dtb
> x1p42100-crd-el2-dtbs := x1p42100-crd.dtb x1-el2.dtbo
> dtb-$(CONFIG_ARCH_QCOM) += x1p42100-crd.dtb x1p42100-crd-el2.dtb
> +x1p42100-lenovo-thinkbook-16-el2-dtbs := x1p42100-lenovo-thinkbook-16.dtb x1-el2.dtbo
> +dtb-$(CONFIG_ARCH_QCOM) += x1p42100-lenovo-thinkbook-16.dtb x1p42100-lenovo-thinkbook-16-el2.dtb
> diff --git a/arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi b/arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi
> index e3888bc143a0aaae23c92d400d48ea94423e0366..378635f7cb0bfe37cf10644a16bd8b3cca447f3c 100644
> --- a/arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi
> +++ b/arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi
> @@ -170,7 +170,7 @@ trip1 {
> };
> };
>
> - pm8010-thermal {
> + pm8010_thermal: pm8010-thermal {
Let's rebase on:
https://lore.kernel.org/linux-arm-msm/20250701183625.1968246-1-alex.vinarskis@gmail.com/
[...]
> + /*
> + * This is an odd one. The camera is physically behind the eusb9 repeater (confirmed) but
> + * if it is placed below the usb_2_dwc3 node, it will be switched of after ~30 seconds.
> + * The reason seems to be that the dwc3 driver does not probe for child nodes when in
> + * host-only mode. But that's the default setting for the xhci controllers due to issues
> + * when in OTG mode. https://lore.kernel.org/all/20241210111444.26240-1-johan+linaro@kernel.org/
> + * The whole reason it is described in the dt (as an USB device) is its requirement for
> + * that additional regulator, and to get power management to switch it off when suspended.
> + * Defining it stand-alone does work.
> + */
> + camera {
> + compatible = "usb5986,1198";
> +
> + vdd-supply = <&vreg_cam_5p0>;
> + };
If the bindings checker is happy, I think we can keep it here for now..
[...]
> + wcd-playback-dai-link {
> + link-name = "WCD Playback";
> +
> + cpu {
> + sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
> + };
> +
> + codec {
'co'dec < 'cp'u
[...]
> +&i2c2 {
> + clock-frequency = <400000>;
> +
> + pinctrl-0 = <&qup_i2c2_data_clk>, <&tpad_default>, <&kybd_default>;
> + pinctrl-names = "default";
> + status = "okay";
> +
> + /* ELAN06FA */
> + touchpad@15 {
5 touchpad variants is a lot. Does DSDT give any clues as to whether
all of them are plausibly present on production hw?
[...]
> +&mdss_dp0_out {
> + data-lanes = <0 1 2 3>;
> + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
> +};
> +
> +&mdss_dp1 {
> + status = "okay";
> +};
> +
> +&mdss_dp1_out {
> + data-lanes = <0 1 2 3>;
Does defining all 4 lanes not upset the driver without additional
patches?
> + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
> +};
> +
> +&mdss_dp2 {
> + status = "okay";
> +};
> +
> +&mdss_dp2_out {
> + data-lanes = <0 1 2 3>;
> + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
> +};
> +
> +&mdss_dp2_phy {
> +// vdda-phy-supply = <&vreg_l3b>;
> +// vdda-pll-supply = <&vreg_l6b>;
The regulators are usecase-specialized, feel free to trust what
is present on the CRD
[...]
> + ports {
> + port@1 {
> + reg = <1>;
> +
> + mdss_dp3_out: endpoint {
> + data-lanes = <0 1 2 3>;
> + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
> +
> + remote-endpoint = <&edp_panel_in>;
> + };
> + };
> + };
> +};
Please rebase on:
https://lore.kernel.org/linux-arm-msm/20250724-move-edp-endpoints-v1-3-6ca569812838@oss.qualcomm.com/
[...]
> +&sdhc_2 {
> + cd-gpios = <&tlmm 71 GPIO_ACTIVE_LOW>;
> + pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
> + pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
> + pinctrl-names = "default", "sleep";
> + vmmc-supply = <&vreg_l9b_2p9>;
> + vqmmc-supply = <&vreg_l6b_1p8>;
> +// bus-width = <4>;
> +// no-sdio;
> +// no-mmc;
Please either remove the '//' or remove the lines
[...]
> +&tlmm {
> + gpio-reserved-ranges = <34 2>, /* Unused */
> + <72 2>, /* Secure EC I2C connection (?) */
> + <238 1>; /* UFS Reset */
Try removing the UFS reset block and see if the platform still
boots, this turned out to be a false flag on CRD
I'd also suggest removing voltage suffixes from regulator names (i.e.
turn them to e.g. vreg_l6b).
Konrad
On 30.07.25 10:50, Konrad Dybcio wrote:
> On 7/1/25 7:02 PM, Jens Glathe via B4 Relay wrote:
>>
>> - pm8010-thermal {
>> + pm8010_thermal: pm8010-thermal {
> Let's rebase on:
>
> https://lore.kernel.org/linux-arm-msm/20250701183625.1968246-1-alex.vinarskis@gmail.com/
Done.
>> + wcd-playback-dai-link {
>> + link-name = "WCD Playback";
>> +
>> + cpu {
>> + sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
>> + };
>> +
>> + codec {
> 'co'dec < 'cp'u
>
Done and checked
>> +&i2c2 {
>> + clock-frequency = <400000>;
>> +
>> + pinctrl-0 = <&qup_i2c2_data_clk>, <&tpad_default>, <&kybd_default>;
>> + pinctrl-names = "default";
>> + status = "okay";
>> +
>> + /* ELAN06FA */
>> + touchpad@15 {
> 5 touchpad variants is a lot. Does DSDT give any clues as to whether
> all of them are plausibly present on production hw?
>
I took sort of a survey among users, and we got mostly @2c (CIRQ1080 or
SYNA2BA6) and one with @38 (FTCS0038). All the others are defined and
look like wired up in the dsdt. There's also 3 display panel variants
defined, all with the same totally odd pwm backlight mechanism according
to the dsdt-embedded xml structures for these. Survey showed all the
same panel as mine, except the one with the diverging touchpad. The
sample size is ~5, so not really representative.
>> +&mdss_dp0_out {
>> + data-lanes = <0 1 2 3>;
>> + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
>> +};
>> +
>> +&mdss_dp1 {
>> + status = "okay";
>> +};
>> +
>> +&mdss_dp1_out {
>> + data-lanes = <0 1 2 3>;
> Does defining all 4 lanes not upset the driver without additional
> patches?
Yes, corrected, thank you.
>> + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
>> +};
>> +
>> +&mdss_dp2 {
>> + status = "okay";
>> +};
>> +
>> +&mdss_dp2_out {
>> + data-lanes = <0 1 2 3>;
>> + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
>> +};
>> +
>> +&mdss_dp2_phy {
>> +// vdda-phy-supply = <&vreg_l3b>;
>> +// vdda-pll-supply = <&vreg_l6b>;
> The regulators are usecase-specialized, feel free to trust what
> is present on the CRD
Removed mdss_dp2 since it's not working reliably yet.
>> + ports {
>> + port@1 {
>> + reg = <1>;
>> +
>> + mdss_dp3_out: endpoint {
>> + data-lanes = <0 1 2 3>;
>> + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
>> +
>> + remote-endpoint = <&edp_panel_in>;
>> + };
>> + };
>> + };
>> +};
> Please rebase on:
>
> https://lore.kernel.org/linux-arm-msm/20250724-move-edp-endpoints-v1-3-6ca569812838@oss.qualcomm.com/
Done.
>> +&sdhc_2 {
>> + cd-gpios = <&tlmm 71 GPIO_ACTIVE_LOW>;
>> + pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
>> + pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
>> + pinctrl-names = "default", "sleep";
>> + vmmc-supply = <&vreg_l9b_2p9>;
>> + vqmmc-supply = <&vreg_l6b_1p8>;
>> +// bus-width = <4>;
>> +// no-sdio;
>> +// no-mmc;
> Please either remove the '//' or remove the lines
>
Done. I have an idea which driver it should be (BayHubTech driver for
the PCI variant) since the Ideapad 5 has actually both variants - the
Slim 5x on pcie3, and the 2in1 on sdhc_2. The Windows driver supports
both interfaces.
>> +&tlmm {
>> + gpio-reserved-ranges = <34 2>, /* Unused */
>> + <72 2>, /* Secure EC I2C connection (?) */
>> + <238 1>; /* UFS Reset */
> Try removing the UFS reset block and see if the platform still
> boots, this turned out to be a false flag on CRD
Done, still working.
> I'd also suggest removing voltage suffixes from regulator names (i.e.
> turn them to e.g. vreg_l6b).
>
I'm not really a fan of this. The X1E dtbs all have the voltage suffix,
and it is actually quite human-readable. Which of course is not the goal
of a dts, but well, as a human writing these I like some orientation help.
with best regards
Jens
© 2016 - 2025 Red Hat, Inc.