Add a node for the PMU module of the WCN6855 present on the qcs615 ride
board. Assign its LDO power outputs to the existing WiFi/BT module.

Signed-off-by: Yu Zhang(Yuriy) <yu.zhang@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/qcs615-ride.dts | 131 +++++++++++++++++++++++++++++++
 1 file changed, 131 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcs615-ride.dts b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
index 011f8ae077c256f079ce1b07720374a9bf721488..69597b6f9d0bccb294a6dcac3fe4eb0e21f2cf7a 100644
--- a/arch/arm64/boot/dts/qcom/qcs615-ride.dts
+++ b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
@@ -18,6 +18,7 @@ aliases {
 		mmc0 = &sdhc_1;
 		mmc1 = &sdhc_2;
 		serial0 = &uart0;
+		serial1 = &uart7;
 	};
 
 	chosen {
@@ -209,6 +210,83 @@ vreg_l17a: ldo17 {
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 		};
 	};
+
+	vreg_conn_1p8: vreg_conn_1p8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_conn_1p8";
+		startup-delay-us = <4000>;
+		enable-active-high;
+		gpio = <&pm8150_gpios 1 GPIO_ACTIVE_HIGH>;
+	};
+
+	vreg_conn_pa: vreg_conn_pa {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_conn_pa";
+		startup-delay-us = <4000>;
+		enable-active-high;
+		gpio = <&pm8150_gpios 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	wcn6855-pmu {
+		compatible = "qcom,wcn6855-pmu";
+
+		pinctrl-0 = <&bt_en_state>, <&wlan_en_state>;
+		pinctrl-names = "default";
+
+		bt-enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
+		wlan-enable-gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>;
+
+		vddio-supply = <&vreg_conn_pa>;
+		vddaon-supply = <&vreg_s5a>;
+		vddpmu-supply = <&vreg_conn_1p8>;
+		vddrfa0p95-supply = <&vreg_s5a>;
+		vddrfa1p3-supply = <&vreg_s6a>;
+		vddrfa1p9-supply = <&vreg_l15a>;
+		vddpcie1p3-supply = <&vreg_s6a>;
+		vddpcie1p9-supply = <&vreg_l15a>;
+
+		regulators {
+			vreg_pmu_rfa_cmn: ldo0 {
+				regulator-name = "vreg_pmu_rfa_cmn";
+			};
+
+			vreg_pmu_aon_0p59: ldo1 {
+				regulator-name = "vreg_pmu_aon_0p59";
+			};
+
+			vreg_pmu_wlcx_0p8: ldo2 {
+				regulator-name = "vreg_pmu_wlcx_0p8";
+			};
+
+			vreg_pmu_wlmx_0p85: ldo3 {
+				regulator-name = "vreg_pmu_wlmx_0p85";
+			};
+
+			vreg_pmu_btcmx_0p85: ldo4 {
+				regulator-name = "vreg_pmu_btcmx_0p85";
+			};
+
+			vreg_pmu_rfa_0p8: ldo5 {
+				regulator-name = "vreg_pmu_rfa_0p8";
+			};
+
+			vreg_pmu_rfa_1p2: ldo6 {
+				regulator-name = "vreg_pmu_rfa_1p2";
+			};
+
+			vreg_pmu_rfa_1p7: ldo7 {
+				regulator-name = "vreg_pmu_rfa_1p7";
+			};
+
+			vreg_pmu_pcie_0p9: ldo8 {
+				regulator-name = "vreg_pmu_pcie_0p9";
+			};
+
+			vreg_pmu_pcie_1p8: ldo9 {
+				regulator-name = "vreg_pmu_pcie_1p8";
+			};
+		};
+	};
 };
 
 &gcc {
@@ -234,6 +312,25 @@ &pcie_phy {
 	status = "okay";
 };
 
+&pcieport0 {
+	wifi@0 {
+		compatible = "pci17cb,1103";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+		qcom,ath11k-calibration-variant = "QC_QCS615_Ride";
+
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p7-supply = <&vreg_pmu_rfa_1p7>;
+		vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+		vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+	};
+};
+
 &pm8150_gpios {
 	usb2_en: usb2-en-state {
 		pins = "gpio10";
@@ -257,6 +354,10 @@ &qupv3_id_0 {
 	status = "okay";
 };
 
+&qupv3_id_1 {
+	status = "okay";
+};
+
 &remoteproc_adsp {
 	firmware-name = "qcom/qcs615/adsp.mbn";
 
@@ -274,6 +375,13 @@ &rpmhcc {
 };
 
 &tlmm {
+	bt_en_state: bt-en-state {
+		pins = "gpio85";
+		function = "gpio";
+		output-low;
+		bias-pull-down;
+	};
+
 	pcie_default_state: pcie-default-state {
 		clkreq-pins {
 			pins = "gpio90";
@@ -296,6 +404,13 @@ wake-pins {
 			bias-pull-up;
 		};
 	};
+
+	wlan_en_state: wlan-en-state {
+		pins = "gpio98";
+		function = "gpio";
+		output-low;
+		bias-pull-down;
+	};
 };
 
 &sdhc_1 {
@@ -336,6 +451,22 @@ &uart0 {
 	status = "okay";
 };
 
+&uart7 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn6855-bt";
+		firmware-name = "QCA6698/hpnv21", "QCA6698/hpbtfw21.tlv";
+
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p7-supply = <&vreg_pmu_rfa_1p7>;
+	};
+};
+
 &usb_1_hsphy {
 	vdd-supply = <&vreg_l5a>;
 	vdda-pll-supply = <&vreg_l12a>;

-- 
2.34.1

On 6/25/25 9:55 AM, Yu Zhang(Yuriy) wrote:
> Add a node for the PMU module of the WCN6855 present on the qcs615 ride
> board. Assign its LDO power outputs to the existing WiFi/BT module.
> 
> Signed-off-by: Yu Zhang(Yuriy) <yu.zhang@oss.qualcomm.com>
> ---

[...]

> +	wcn6855-pmu {
> +		compatible = "qcom,wcn6855-pmu";
> +
> +		pinctrl-0 = <&bt_en_state>, <&wlan_en_state>;
> +		pinctrl-names = "default";
> +
> +		bt-enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
> +		wlan-enable-gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>;
> +
> +		vddio-supply = <&vreg_conn_pa>;
> +		vddaon-supply = <&vreg_s5a>;
> +		vddpmu-supply = <&vreg_conn_1p8>;
> +		vddrfa0p95-supply = <&vreg_s5a>;
> +		vddrfa1p3-supply = <&vreg_s6a>;
> +		vddrfa1p9-supply = <&vreg_l15a>;
> +		vddpcie1p3-supply = <&vreg_s6a>;
> +		vddpcie1p9-supply = <&vreg_l15a>;

You're missing some supplies (in a couple nodes), as the bot pointed out 

[...]

> +&pcieport0 {
> +	wifi@0 {
> +		compatible = "pci17cb,1103";
> +		reg = <0x10000 0x0 0x0 0x0 0x0>;
> +
> +		qcom,ath11k-calibration-variant = "QC_QCS615_Ride";

Use 'qcom,calibration-variant' instead

[...]

>  &tlmm {
> +	bt_en_state: bt-en-state {
> +		pins = "gpio85";
> +		function = "gpio";
> +		output-low;
> +		bias-pull-down;

Please put output properties below bias (for consistency)

Konrad