MAINTAINERS | 1 + drivers/net/phy/Kconfig | 12 + drivers/net/phy/Makefile | 1 + drivers/net/phy/mxl-86110.c | 570 ++++++++++++++++++++++++++++++++++++ 4 files changed, 584 insertions(+) create mode 100644 drivers/net/phy/mxl-86110.c
From: "stefano.radaelli" <stefano.radaelli@tastitalia.com>
Add support for the MaxLinear MxL86110 Gigabit Ethernet PHY, a low-power,
cost-optimized transceiver supporting 10/100/1000 Mbps over twisted-pair
copper, compliant with IEEE 802.3.
The driver implements basic features such as:
- Device initialization
- RGMII interface timing configuration
- Wake-on-LAN support
- LED initialization and control via /sys/class/leds
This driver has been tested on multiple Variscite boards, including:
- VAR-SOM-MX93 (i.MX93)
- VAR-SOM-MX8M-PLUS (i.MX8MP)
Example boot log showing driver probe:
[ 7.692101] imx-dwmac 428a0000.ethernet eth0:
PHY [stmmac-0:00] driver [MXL86110 Gigabit Ethernet] (irq=POLL)
Signed-off-by: stefano.radaelli <stefano.radaelli@tastitalia.com>
---
MAINTAINERS | 1 +
drivers/net/phy/Kconfig | 12 +
drivers/net/phy/Makefile | 1 +
drivers/net/phy/mxl-86110.c | 570 ++++++++++++++++++++++++++++++++++++
4 files changed, 584 insertions(+)
create mode 100644 drivers/net/phy/mxl-86110.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 84e99e991f53..cca046bbe00b 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -14653,6 +14653,7 @@ MAXLINEAR ETHERNET PHY DRIVER
M: Xu Liang <lxu@maxlinear.com>
L: netdev@vger.kernel.org
S: Supported
+F: drivers/net/phy/mxl-86110.c
F: drivers/net/phy/mxl-gpy.c
MCAN MMIO DEVICE DRIVER
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 677d56e06539..fbaa009c146d 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -263,6 +263,18 @@ config MAXLINEAR_GPHY
Support for the Maxlinear GPY115, GPY211, GPY212, GPY215,
GPY241, GPY245 PHYs.
+config MAXLINEAR_86110_PHY
+ tristate "MaxLinear MXL86110 PHY support"
+ help
+ Support for the MaxLinear MXL86110 Gigabit Ethernet
+ Physical Layer transceiver.
+ The MXL86110 is commonly used in networking equipment such as
+ routers, switches, and embedded systems, providing the
+ physical interface for 10/100/1000 Mbps Ethernet connections
+ over copper media.
+ If you are using a board with the MXL86110 PHY connected to your
+ Ethernet MAC, you should enable this option.
+
source "drivers/net/phy/mediatek/Kconfig"
config MICREL_PHY
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index 59ac3a9a3177..171a80228c12 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -75,6 +75,7 @@ obj-$(CONFIG_MARVELL_PHY) += marvell.o
obj-$(CONFIG_MARVELL_88Q2XXX_PHY) += marvell-88q2xxx.o
obj-$(CONFIG_MARVELL_88X2222_PHY) += marvell-88x2222.o
obj-$(CONFIG_MAXLINEAR_GPHY) += mxl-gpy.o
+obj-$(CONFIG_MAXLINEAR_86110_PHY) += mxl-86110.o
obj-y += mediatek/
obj-$(CONFIG_MESON_GXL_PHY) += meson-gxl.o
obj-$(CONFIG_MICREL_KS8995MA) += spi_ks8995.o
diff --git a/drivers/net/phy/mxl-86110.c b/drivers/net/phy/mxl-86110.c
new file mode 100644
index 000000000000..63f32c49fcc1
--- /dev/null
+++ b/drivers/net/phy/mxl-86110.c
@@ -0,0 +1,570 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * PHY driver for Maxlinear MXL86110
+ *
+ * Copyright 2023 MaxLinear Inc.
+ *
+ */
+
+#include <linux/bitfield.h>
+#include <linux/etherdevice.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy.h>
+
+/* PHY ID */
+#define PHY_ID_MXL86110 0xc1335580
+
+/* required to access extended registers */
+#define MXL86110_EXTD_REG_ADDR_OFFSET 0x1E
+#define MXL86110_EXTD_REG_ADDR_DATA 0x1F
+#define PHY_IRQ_ENABLE_REG 0x12
+#define PHY_IRQ_ENABLE_REG_WOL BIT(6)
+
+/* SyncE Configuration Register - COM_EXT SYNCE_CFG */
+#define MXL86110_EXT_SYNCE_CFG_REG 0xA012
+#define MXL86110_EXT_SYNCE_CFG_CLK_FRE_SEL BIT(4)
+#define MXL86110_EXT_SYNCE_CFG_EN_SYNC_E_DURING_LNKDN BIT(5)
+#define MXL86110_EXT_SYNCE_CFG_EN_SYNC_E BIT(6)
+#define MXL86110_EXT_SYNCE_CFG_CLK_SRC_SEL_MASK GENMASK(3, 1)
+#define MXL86110_EXT_SYNCE_CFG_CLK_SRC_SEL_125M_PLL 0
+#define MXL86110_EXT_SYNCE_CFG_CLK_SRC_SEL_25M 4
+
+/* WOL registers */
+#define MXL86110_WOL_MAC_ADDR_HIGH_EXTD_REG 0xA007 /* high-> FF:FF */
+#define MXL86110_WOL_MAC_ADDR_MIDDLE_EXTD_REG 0xA008 /* middle-> :FF:FF <-middle */
+#define MXL86110_WOL_MAC_ADDR_LOW_EXTD_REG 0xA009 /* :FF:FF <-low */
+
+#define MXL86110_EXT_WOL_CFG_REG 0xA00A
+#define MXL86110_EXT_WOL_CFG_WOLE_MASK BIT(3)
+#define MXL86110_EXT_WOL_CFG_WOLE_DISABLE 0
+#define MXL86110_EXT_WOL_CFG_WOLE_ENABLE BIT(3)
+
+/* RGMII register */
+#define MXL86110_EXT_RGMII_CFG1_REG 0xA003
+/* delay can be adjusted in steps of about 150ps */
+#define MXL86110_EXT_RGMII_CFG1_RX_NO_DELAY (0x0 << 10)
+/* Closest value to 2000 ps */
+#define MXL86110_EXT_RGMII_CFG1_RX_DELAY_1950PS (0xD << 10)
+#define MXL86110_EXT_RGMII_CFG1_RX_DELAY_MASK GENMASK(13, 10)
+
+#define MXL86110_EXT_RGMII_CFG1_TX_1G_DELAY_1950PS (0xD << 0)
+#define MXL86110_EXT_RGMII_CFG1_TX_1G_DELAY_MASK GENMASK(3, 0)
+
+#define MXL86110_EXT_RGMII_CFG1_TX_10MB_100MB_DELAY_1950PS (0xD << 4)
+#define MXL86110_EXT_RGMII_CFG1_TX_10MB_100MB_DELAY_MASK GENMASK(7, 4)
+
+#define MXL86110_EXT_RGMII_CFG1_FULL_MASK \
+ ((MXL86110_EXT_RGMII_CFG1_RX_DELAY_MASK) | \
+ (MXL86110_EXT_RGMII_CFG1_TX_1G_DELAY_MASK) | \
+ (MXL86110_EXT_RGMII_CFG1_TX_10MB_100MB_DELAY_MASK))
+
+/* EXT Sleep Control register */
+#define MXL86110_UTP_EXT_SLEEP_CTRL_REG 0x27
+#define MXL86110_UTP_EXT_SLEEP_CTRL_EN_SLEEP_SW_OFF 0
+#define MXL86110_UTP_EXT_SLEEP_CTRL_EN_SLEEP_SW_MASK BIT(15)
+
+/* RGMII In-Band Status and MDIO Configuration Register */
+#define MXL86110_EXT_RGMII_MDIO_CFG 0xA005
+#define MXL86110_EXT_RGMII_MDIO_CFG_EPA0_MASK GENMASK(6, 6)
+#define MXL86110_EXT_RGMII_MDIO_CFG_EBA_MASK GENMASK(5, 5)
+#define MXL86110_EXT_RGMII_MDIO_CFG_BA_MASK GENMASK(4, 0)
+
+#define MXL86110_MAX_LEDS 3
+/* LED registers and defines */
+#define MXL86110_LED0_CFG_REG 0xA00C
+#define MXL86110_LED1_CFG_REG 0xA00D
+#define MXL86110_LED2_CFG_REG 0xA00E
+
+#define MXL86110_LEDX_CFG_TRAFFIC_ACT_BLINK_IND BIT(13)
+#define MXL86110_LEDX_CFG_LINK_UP_FULL_DUPLEX_ON BIT(12)
+#define MXL86110_LEDX_CFG_LINK_UP_HALF_DUPLEX_ON BIT(11)
+#define MXL86110_LEDX_CFG_LINK_UP_TX_ACT_ON BIT(10) /* LED 0,1,2 default */
+#define MXL86110_LEDX_CFG_LINK_UP_RX_ACT_ON BIT(9) /* LED 0,1,2 default */
+#define MXL86110_LEDX_CFG_LINK_UP_TX_ON BIT(8)
+#define MXL86110_LEDX_CFG_LINK_UP_RX_ON BIT(7)
+#define MXL86110_LEDX_CFG_LINK_UP_1GB_ON BIT(6) /* LED 2 default */
+#define MXL86110_LEDX_CFG_LINK_UP_100MB_ON BIT(5) /* LED 1 default */
+#define MXL86110_LEDX_CFG_LINK_UP_10MB_ON BIT(4) /* LED 0 default */
+#define MXL86110_LEDX_CFG_LINK_UP_COLLISION BIT(3)
+#define MXL86110_LEDX_CFG_LINK_UP_1GB_BLINK BIT(2)
+#define MXL86110_LEDX_CFG_LINK_UP_100MB_BLINK BIT(1)
+#define MXL86110_LEDX_CFG_LINK_UP_10MB_BLINK BIT(0)
+
+#define MXL86110_LED_BLINK_CFG_REG 0xA00F
+#define MXL86110_LED_BLINK_CFG_FREQ_MODE1_2HZ 0
+#define MXL86110_LED_BLINK_CFG_FREQ_MODE1_4HZ BIT(0)
+#define MXL86110_LED_BLINK_CFG_FREQ_MODE1_8HZ BIT(1)
+#define MXL86110_LED_BLINK_CFG_FREQ_MODE1_16HZ (BIT(1) | BIT(0))
+#define MXL86110_LED_BLINK_CFG_FREQ_MODE2_2HZ 0
+#define MXL86110_LED_BLINK_CFG_FREQ_MODE2_4HZ BIT(2)
+#define MXL86110_LED_BLINK_CFG_FREQ_MODE2_8HZ BIT(3)
+#define MXL86110_LED_BLINK_CFG_FREQ_MODE2_16HZ (BIT(3) | BIT(2))
+#define MXL86110_LED_BLINK_CFG_DUTY_CYCLE_50_PERC_ON 0
+#define MXL86110_LED_BLINK_CFG_DUTY_CYCLE_67_PERC_ON (BIT(4))
+#define MXL86110_LED_BLINK_CFG_DUTY_CYCLE_75_PERC_ON (BIT(5))
+#define MXL86110_LED_BLINK_CFG_DUTY_CYCLE_83_PERC_ON (BIT(5) | BIT(4))
+#define MXL86110_LED_BLINK_CFG_DUTY_CYCLE_50_PERC_OFF (BIT(6))
+#define MXL86110_LED_BLINK_CFG_DUTY_CYCLE_33_PERC_ON (BIT(6) | BIT(4))
+#define MXL86110_LED_BLINK_CFG_DUTY_CYCLE_25_PERC_ON (BIT(6) | BIT(5))
+#define MXL86110_LED_BLINK_CFG_DUTY_CYCLE_17_PERC_ON (BIT(6) | BIT(5) | BIT(4))
+
+/* Chip Configuration Register - COM_EXT_CHIP_CFG */
+#define MXL86110_EXT_CHIP_CFG_REG 0xA001
+#define MXL86110_EXT_CHIP_CFG_RXDLY_ENABLE BIT(8)
+#define MXL86110_EXT_CHIP_CFG_SW_RST_N_MODE BIT(15)
+
+/**
+ * mxl86110_write_extended_reg() - write to a PHY's extended register
+ * @phydev: pointer to a &struct phy_device
+ * @regnum: register number to write
+ * @val: value to write to @regnum
+ *
+ * NOTE: This function assumes the caller already holds the MDIO bus lock
+ * or otherwise has exclusive access to the PHY.
+ *
+ * returns 0 or negative error code
+ */
+static int mxl86110_write_extended_reg(struct phy_device *phydev, u16 regnum, u16 val)
+{
+ int ret;
+
+ ret = __phy_write(phydev, MXL86110_EXTD_REG_ADDR_OFFSET, regnum);
+ if (ret < 0)
+ return ret;
+
+ return __phy_write(phydev, MXL86110_EXTD_REG_ADDR_DATA, val);
+}
+
+/**
+ * mxl86110_read_extended_reg - Read a PHY's extended register
+ * @phydev: Pointer to the PHY device structure
+ * @regnum: Extended register number to read (address written to reg 30)
+ *
+ * Reads the content of a PHY extended register using the MaxLinear
+ * 2-step access mechanism: write the register address to reg 30 (0x1E),
+ * then read the value from reg 31 (0x1F).
+ *
+ * NOTE: This function assumes the caller already holds the MDIO bus lock
+ * or otherwise has exclusive access to the PHY.
+ *
+ * Return: 16-bit register value on success, or negative errno code on failure.
+ */
+static int mxl86110_read_extended_reg(struct phy_device *phydev, u16 regnum)
+{
+ int ret;
+
+ ret = __phy_write(phydev, MXL86110_EXTD_REG_ADDR_OFFSET, regnum);
+ if (ret < 0)
+ return ret;
+ return __phy_read(phydev, MXL86110_EXTD_REG_ADDR_DATA);
+}
+
+/**
+ * mxl86110_modify_extended_reg() - modify bits of a PHY's extended register
+ * @phydev: pointer to the phy_device
+ * @regnum: register number to write
+ * @mask: bit mask of bits to clear
+ * @set: bit mask of bits to set
+ *
+ * NOTE: register value = (old register value & ~mask) | set.
+ * This function assumes the caller already holds the MDIO bus lock
+ * or otherwise has exclusive access to the PHY.
+ *
+ * returns 0 or negative error code
+ */
+static int mxl86110_modify_extended_reg(struct phy_device *phydev, u16 regnum, u16 mask,
+ u16 set)
+{
+ int ret;
+
+ ret = __phy_write(phydev, MXL86110_EXTD_REG_ADDR_OFFSET, regnum);
+ if (ret < 0)
+ return ret;
+
+ return __phy_modify(phydev, MXL86110_EXTD_REG_ADDR_DATA, mask, set);
+}
+
+/**
+ * mxl86110_get_wol() - report if wake-on-lan is enabled
+ * @phydev: pointer to the phy_device
+ * @wol: a pointer to a &struct ethtool_wolinfo
+ */
+static void mxl86110_get_wol(struct phy_device *phydev, struct ethtool_wolinfo *wol)
+{
+ int value;
+
+ wol->supported = WAKE_MAGIC;
+ wol->wolopts = 0;
+ phy_lock_mdio_bus(phydev);
+ value = mxl86110_read_extended_reg(phydev, MXL86110_EXT_WOL_CFG_REG);
+ phy_unlock_mdio_bus(phydev);
+ if (value >= 0 && (value & MXL86110_EXT_WOL_CFG_WOLE_MASK))
+ wol->wolopts |= WAKE_MAGIC;
+}
+
+/**
+ * mxl86110_set_wol() - enable/disable wake-on-lan
+ * @phydev: pointer to the phy_device
+ * @wol: a pointer to a &struct ethtool_wolinfo
+ *
+ * Configures the WOL Magic Packet MAC
+ * returns 0 or negative errno code
+ */
+static int mxl86110_set_wol(struct phy_device *phydev, struct ethtool_wolinfo *wol)
+{
+ struct net_device *netdev;
+ const u8 *mac;
+ int ret = 0;
+
+ phy_lock_mdio_bus(phydev);
+
+ if (wol->wolopts & WAKE_MAGIC) {
+ netdev = phydev->attached_dev;
+ if (!netdev) {
+ ret = -ENODEV;
+ goto error;
+ }
+
+ /* Configure the MAC address of the WOL magic packet */
+ mac = (const u8 *)netdev->dev_addr;
+ ret = mxl86110_write_extended_reg(phydev, MXL86110_WOL_MAC_ADDR_HIGH_EXTD_REG,
+ ((mac[0] << 8) | mac[1]));
+ if (ret < 0)
+ goto error;
+
+ ret = mxl86110_write_extended_reg(phydev, MXL86110_WOL_MAC_ADDR_MIDDLE_EXTD_REG,
+ ((mac[2] << 8) | mac[3]));
+ if (ret < 0)
+ goto error;
+
+ ret = mxl86110_write_extended_reg(phydev, MXL86110_WOL_MAC_ADDR_LOW_EXTD_REG,
+ ((mac[4] << 8) | mac[5]));
+ if (ret < 0)
+ goto error;
+
+ ret = mxl86110_modify_extended_reg(phydev, MXL86110_EXT_WOL_CFG_REG,
+ MXL86110_EXT_WOL_CFG_WOLE_MASK,
+ MXL86110_EXT_WOL_CFG_WOLE_ENABLE);
+ if (ret < 0)
+ goto error;
+
+ /* Enables Wake-on-LAN interrupt in the PHY. */
+ ret = __phy_modify(phydev, PHY_IRQ_ENABLE_REG, 0,
+ PHY_IRQ_ENABLE_REG_WOL);
+ if (ret < 0)
+ goto error;
+
+ phydev_dbg(phydev, "%s, WOL Magic packet MAC: %02X:%02X:%02X:%02X:%02X:%02X\n",
+ __func__, mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]);
+
+ } else {
+ ret = mxl86110_modify_extended_reg(phydev, MXL86110_EXT_WOL_CFG_REG,
+ MXL86110_EXT_WOL_CFG_WOLE_MASK,
+ MXL86110_EXT_WOL_CFG_WOLE_DISABLE);
+ if (ret < 0)
+ goto error;
+
+ /* Disables Wake-on-LAN interrupt in the PHY. */
+ ret = __phy_modify(phydev, PHY_IRQ_ENABLE_REG,
+ PHY_IRQ_ENABLE_REG_WOL, 0);
+ if (ret < 0)
+ goto error;
+ }
+
+ phy_unlock_mdio_bus(phydev);
+ return 0;
+error:
+ phy_unlock_mdio_bus(phydev);
+ return ret;
+}
+
+static const unsigned long supported_triggers = (BIT(TRIGGER_NETDEV_LINK_10) |
+ BIT(TRIGGER_NETDEV_LINK_100) |
+ BIT(TRIGGER_NETDEV_LINK_1000) |
+ BIT(TRIGGER_NETDEV_HALF_DUPLEX) |
+ BIT(TRIGGER_NETDEV_FULL_DUPLEX) |
+ BIT(TRIGGER_NETDEV_TX) |
+ BIT(TRIGGER_NETDEV_RX));
+
+static int mxl86110_led_hw_is_supported(struct phy_device *phydev, u8 index,
+ unsigned long rules)
+{
+ if (index >= MXL86110_MAX_LEDS)
+ return -EINVAL;
+
+ /* All combinations of the supported triggers are allowed */
+ if (rules & ~supported_triggers)
+ return -EOPNOTSUPP;
+
+ return 0;
+}
+
+static int mxl86110_led_hw_control_get(struct phy_device *phydev, u8 index,
+ unsigned long *rules)
+{
+ u16 val;
+
+ if (index >= MXL86110_MAX_LEDS)
+ return -EINVAL;
+
+ phy_lock_mdio_bus(phydev);
+ val = mxl86110_read_extended_reg(phydev, MXL86110_LED0_CFG_REG + index);
+ phy_unlock_mdio_bus(phydev);
+ if (val < 0)
+ return val;
+
+ if (val & MXL86110_LEDX_CFG_LINK_UP_TX_ACT_ON)
+ *rules |= BIT(TRIGGER_NETDEV_TX);
+
+ if (val & MXL86110_LEDX_CFG_LINK_UP_RX_ACT_ON)
+ *rules |= BIT(TRIGGER_NETDEV_RX);
+
+ if (val & MXL86110_LEDX_CFG_LINK_UP_HALF_DUPLEX_ON)
+ *rules |= BIT(TRIGGER_NETDEV_HALF_DUPLEX);
+
+ if (val & MXL86110_LEDX_CFG_LINK_UP_FULL_DUPLEX_ON)
+ *rules |= BIT(TRIGGER_NETDEV_FULL_DUPLEX);
+
+ if (val & MXL86110_LEDX_CFG_LINK_UP_10MB_ON)
+ *rules |= BIT(TRIGGER_NETDEV_LINK_10);
+
+ if (val & MXL86110_LEDX_CFG_LINK_UP_100MB_ON)
+ *rules |= BIT(TRIGGER_NETDEV_LINK_100);
+
+ if (val & MXL86110_LEDX_CFG_LINK_UP_1GB_ON)
+ *rules |= BIT(TRIGGER_NETDEV_LINK_1000);
+
+ return 0;
+};
+
+static int mxl86110_led_hw_control_set(struct phy_device *phydev, u8 index,
+ unsigned long rules)
+{
+ u16 val = 0;
+ int ret;
+
+ if (index >= MXL86110_MAX_LEDS)
+ return -EINVAL;
+
+ if (rules & BIT(TRIGGER_NETDEV_LINK_10))
+ val |= MXL86110_LEDX_CFG_LINK_UP_10MB_ON;
+
+ if (rules & BIT(TRIGGER_NETDEV_LINK_100))
+ val |= MXL86110_LEDX_CFG_LINK_UP_100MB_ON;
+
+ if (rules & BIT(TRIGGER_NETDEV_LINK_1000))
+ val |= MXL86110_LEDX_CFG_LINK_UP_1GB_ON;
+
+ if (rules & BIT(TRIGGER_NETDEV_TX))
+ val |= MXL86110_LEDX_CFG_LINK_UP_TX_ACT_ON;
+
+ if (rules & BIT(TRIGGER_NETDEV_RX))
+ val |= MXL86110_LEDX_CFG_LINK_UP_RX_ACT_ON;
+
+ if (rules & BIT(TRIGGER_NETDEV_HALF_DUPLEX))
+ val |= MXL86110_LEDX_CFG_LINK_UP_HALF_DUPLEX_ON;
+
+ if (rules & BIT(TRIGGER_NETDEV_FULL_DUPLEX))
+ val |= MXL86110_LEDX_CFG_LINK_UP_FULL_DUPLEX_ON;
+
+ if (rules & BIT(TRIGGER_NETDEV_TX) ||
+ rules & BIT(TRIGGER_NETDEV_RX))
+ val |= MXL86110_LEDX_CFG_TRAFFIC_ACT_BLINK_IND;
+
+ phy_lock_mdio_bus(phydev);
+ ret = mxl86110_write_extended_reg(phydev, MXL86110_LED0_CFG_REG + index, val);
+ phy_unlock_mdio_bus(phydev);
+ if (ret)
+ return ret;
+
+ return 0;
+};
+
+/**
+ * mxl86110_synce_clk_cfg() - applies syncE/clk output configuration
+ * @phydev: pointer to the phy_device
+ *
+ * Custom settings can be defined in custom config section of the driver
+ * returns 0 or negative errno code
+ */
+static int mxl86110_synce_clk_cfg(struct phy_device *phydev)
+{
+ u16 mask = 0, value = 0;
+ int ret = 0;
+
+ /*
+ * Configures the clock output to its default setting as per the datasheet.
+ * This results in a 25MHz clock output being selected in the
+ * COM_EXT_SYNCE_CFG register for SyncE configuration.
+ */
+ value = MXL86110_EXT_SYNCE_CFG_EN_SYNC_E |
+ FIELD_PREP(MXL86110_EXT_SYNCE_CFG_CLK_SRC_SEL_MASK,
+ MXL86110_EXT_SYNCE_CFG_CLK_SRC_SEL_25M);
+ mask = MXL86110_EXT_SYNCE_CFG_EN_SYNC_E |
+ MXL86110_EXT_SYNCE_CFG_CLK_SRC_SEL_MASK |
+ MXL86110_EXT_SYNCE_CFG_CLK_FRE_SEL;
+
+ /* Write clock output configuration */
+ ret = mxl86110_modify_extended_reg(phydev, MXL86110_EXT_SYNCE_CFG_REG,
+ mask, value);
+
+ return ret;
+}
+
+/**
+ * mxl86110_broadcast_cfg - Configure MDIO broadcast setting for PHY
+ * @phydev: Pointer to the PHY device structure
+ *
+ * This function configures the MDIO broadcast behavior of the MxL86110 PHY.
+ * Currently, broadcast mode is explicitly disabled by clearing the EPA0 bit
+ * in the RGMII_MDIO_CFG extended register.
+ *
+ * Return: 0 on success or a negative errno code on failure.
+ */
+static int mxl86110_broadcast_cfg(struct phy_device *phydev)
+{
+ int ret = 0;
+ u16 val;
+
+ val = mxl86110_read_extended_reg(phydev, MXL86110_EXT_RGMII_MDIO_CFG);
+ if (val < 0)
+ return val;
+
+ val &= ~MXL86110_EXT_RGMII_MDIO_CFG_EPA0_MASK;
+ ret = mxl86110_write_extended_reg(phydev, MXL86110_EXT_RGMII_MDIO_CFG, val);
+
+ return ret;
+}
+
+/**
+ * mxl86110_enable_led_activity_blink - Enable LEDs activity blink on PHY
+ * @phydev: Pointer to the PHY device structure
+ *
+ * Configure all PHY LEDs to blink on traffic activity regardless of their
+ * ON or OFF state. This behavior allows each LED to serve as a pure activity
+ * indicator, independently of its use as a link status indicator.
+ *
+ * By default, each LED blinks only when it is also in the ON state. This function
+ * modifies the appropriate registers (LABx fields) to enable blinking even
+ * when the LEDs are OFF, to allow the LED to be used as a traffic indicator
+ * without requiring it to also serve as a link status LED.
+ *
+ * NOTE: Any further LED customization can be performed via the
+ * /sys/class/led interface; the functions led_hw_is_supported, led_hw_control_get, and
+ * led_hw_control_set are used to support this mechanism.
+ *
+ * Return: 0 on success or a negative errno code on failure.
+ */
+static int mxl86110_enable_led_activity_blink(struct phy_device *phydev)
+{
+ int ret, index;
+ u16 val = 0;
+
+ for (index = 0; index < MXL86110_MAX_LEDS; index++) {
+ val = mxl86110_read_extended_reg(phydev, MXL86110_LED0_CFG_REG + index);
+ if (val < 0)
+ return val;
+
+ val |= MXL86110_LEDX_CFG_TRAFFIC_ACT_BLINK_IND;
+ ret = mxl86110_write_extended_reg(phydev, MXL86110_LED0_CFG_REG + index, val);
+ if (ret < 0)
+ return ret;
+ }
+
+ return 0;
+};
+
+/**
+ * mxl86110_config_init() - initialize the PHY
+ * @phydev: pointer to the phy_device
+ *
+ * returns 0 or negative errno code
+ */
+static int mxl86110_config_init(struct phy_device *phydev)
+{
+ unsigned int val = 0;
+ int ret;
+
+ phy_lock_mdio_bus(phydev);
+
+ /* configure syncE / clk output */
+ ret = mxl86110_synce_clk_cfg(phydev);
+ if (ret < 0)
+ goto error;
+
+ switch (phydev->interface) {
+ case PHY_INTERFACE_MODE_RGMII:
+ val = 0;
+ break;
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ val = MXL86110_EXT_RGMII_CFG1_RX_DELAY_1950PS;
+ break;
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ val = MXL86110_EXT_RGMII_CFG1_TX_1G_DELAY_1950PS |
+ MXL86110_EXT_RGMII_CFG1_TX_10MB_100MB_DELAY_1950PS;
+ break;
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ val = MXL86110_EXT_RGMII_CFG1_TX_1G_DELAY_1950PS |
+ MXL86110_EXT_RGMII_CFG1_TX_10MB_100MB_DELAY_1950PS;
+ val |= MXL86110_EXT_RGMII_CFG1_RX_DELAY_1950PS;
+ break;
+ default:
+ ret = -EINVAL;
+ goto error;
+ }
+ ret = mxl86110_modify_extended_reg(phydev, MXL86110_EXT_RGMII_CFG1_REG,
+ MXL86110_EXT_RGMII_CFG1_FULL_MASK, val);
+ if (ret < 0)
+ goto error;
+
+ /* Configure RXDLY (RGMII Rx Clock Delay) to disable the default additional
+ * delay value on RX_CLK (2 ns for 125 MHz, 8 ns for 25 MHz/2.5 MHz)
+ * and use just the digital one selected before
+ */
+ ret = mxl86110_modify_extended_reg(phydev, MXL86110_EXT_CHIP_CFG_REG,
+ MXL86110_EXT_CHIP_CFG_RXDLY_ENABLE, 0);
+ if (ret < 0)
+ goto error;
+
+ ret = mxl86110_enable_led_activity_blink(phydev);
+ if (ret < 0)
+ goto error;
+
+ ret = mxl86110_broadcast_cfg(phydev);
+ if (ret < 0)
+ goto error;
+
+ phy_unlock_mdio_bus(phydev);
+ return 0;
+error:
+ phy_unlock_mdio_bus(phydev);
+ return ret;
+}
+
+static struct phy_driver mxl_phy_drvs[] = {
+ {
+ PHY_ID_MATCH_EXACT(PHY_ID_MXL86110),
+ .name = "MXL86110 Gigabit Ethernet",
+ .config_init = mxl86110_config_init,
+ .get_wol = mxl86110_get_wol,
+ .set_wol = mxl86110_set_wol,
+ .led_hw_is_supported = mxl86110_led_hw_is_supported,
+ .led_hw_control_get = mxl86110_led_hw_control_get,
+ .led_hw_control_set = mxl86110_led_hw_control_set,
+ },
+};
+
+module_phy_driver(mxl_phy_drvs);
+
+static const struct mdio_device_id __maybe_unused mxl_tbl[] = {
+ { PHY_ID_MATCH_EXACT(PHY_ID_MXL86110) },
+ { }
+};
+
+MODULE_DEVICE_TABLE(mdio, mxl_tbl);
+
+MODULE_DESCRIPTION("MaxLinear MXL86110 PHY driver");
+MODULE_AUTHOR("Stefano Radaelli");
+MODULE_LICENSE("GPL");
base-commit: 894fbb55e60cab4ea740f6c65a08b5f8155221f4
--
2.43.0Please don't consider this e-mail, I will start a new thread
Il giorno ven 16 mag 2025 alle ore 16:16 Stefano Radaelli
<stefano.radaelli21@gmail.com> ha scritto:
>
> From: "stefano.radaelli" <stefano.radaelli@tastitalia.com>
>
> Add support for the MaxLinear MxL86110 Gigabit Ethernet PHY, a low-power,
> cost-optimized transceiver supporting 10/100/1000 Mbps over twisted-pair
> copper, compliant with IEEE 802.3.
>
> The driver implements basic features such as:
> - Device initialization
> - RGMII interface timing configuration
> - Wake-on-LAN support
> - LED initialization and control via /sys/class/leds
>
> This driver has been tested on multiple Variscite boards, including:
> - VAR-SOM-MX93 (i.MX93)
> - VAR-SOM-MX8M-PLUS (i.MX8MP)
>
> Example boot log showing driver probe:
> [ 7.692101] imx-dwmac 428a0000.ethernet eth0:
> PHY [stmmac-0:00] driver [MXL86110 Gigabit Ethernet] (irq=POLL)
>
> Signed-off-by: stefano.radaelli <stefano.radaelli@tastitalia.com>
> ---
> MAINTAINERS | 1 +
> drivers/net/phy/Kconfig | 12 +
> drivers/net/phy/Makefile | 1 +
> drivers/net/phy/mxl-86110.c | 570 ++++++++++++++++++++++++++++++++++++
> 4 files changed, 584 insertions(+)
> create mode 100644 drivers/net/phy/mxl-86110.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 84e99e991f53..cca046bbe00b 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -14653,6 +14653,7 @@ MAXLINEAR ETHERNET PHY DRIVER
> M: Xu Liang <lxu@maxlinear.com>
> L: netdev@vger.kernel.org
> S: Supported
> +F: drivers/net/phy/mxl-86110.c
> F: drivers/net/phy/mxl-gpy.c
>
> MCAN MMIO DEVICE DRIVER
> diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
> index 677d56e06539..fbaa009c146d 100644
> --- a/drivers/net/phy/Kconfig
> +++ b/drivers/net/phy/Kconfig
> @@ -263,6 +263,18 @@ config MAXLINEAR_GPHY
> Support for the Maxlinear GPY115, GPY211, GPY212, GPY215,
> GPY241, GPY245 PHYs.
>
> +config MAXLINEAR_86110_PHY
> + tristate "MaxLinear MXL86110 PHY support"
> + help
> + Support for the MaxLinear MXL86110 Gigabit Ethernet
> + Physical Layer transceiver.
> + The MXL86110 is commonly used in networking equipment such as
> + routers, switches, and embedded systems, providing the
> + physical interface for 10/100/1000 Mbps Ethernet connections
> + over copper media.
> + If you are using a board with the MXL86110 PHY connected to your
> + Ethernet MAC, you should enable this option.
> +
> source "drivers/net/phy/mediatek/Kconfig"
>
> config MICREL_PHY
> diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
> index 59ac3a9a3177..171a80228c12 100644
> --- a/drivers/net/phy/Makefile
> +++ b/drivers/net/phy/Makefile
> @@ -75,6 +75,7 @@ obj-$(CONFIG_MARVELL_PHY) += marvell.o
> obj-$(CONFIG_MARVELL_88Q2XXX_PHY) += marvell-88q2xxx.o
> obj-$(CONFIG_MARVELL_88X2222_PHY) += marvell-88x2222.o
> obj-$(CONFIG_MAXLINEAR_GPHY) += mxl-gpy.o
> +obj-$(CONFIG_MAXLINEAR_86110_PHY) += mxl-86110.o
> obj-y += mediatek/
> obj-$(CONFIG_MESON_GXL_PHY) += meson-gxl.o
> obj-$(CONFIG_MICREL_KS8995MA) += spi_ks8995.o
> diff --git a/drivers/net/phy/mxl-86110.c b/drivers/net/phy/mxl-86110.c
> new file mode 100644
> index 000000000000..63f32c49fcc1
> --- /dev/null
> +++ b/drivers/net/phy/mxl-86110.c
> @@ -0,0 +1,570 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * PHY driver for Maxlinear MXL86110
> + *
> + * Copyright 2023 MaxLinear Inc.
> + *
> + */
> +
> +#include <linux/bitfield.h>
> +#include <linux/etherdevice.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/phy.h>
> +
> +/* PHY ID */
> +#define PHY_ID_MXL86110 0xc1335580
> +
> +/* required to access extended registers */
> +#define MXL86110_EXTD_REG_ADDR_OFFSET 0x1E
> +#define MXL86110_EXTD_REG_ADDR_DATA 0x1F
> +#define PHY_IRQ_ENABLE_REG 0x12
> +#define PHY_IRQ_ENABLE_REG_WOL BIT(6)
> +
> +/* SyncE Configuration Register - COM_EXT SYNCE_CFG */
> +#define MXL86110_EXT_SYNCE_CFG_REG 0xA012
> +#define MXL86110_EXT_SYNCE_CFG_CLK_FRE_SEL BIT(4)
> +#define MXL86110_EXT_SYNCE_CFG_EN_SYNC_E_DURING_LNKDN BIT(5)
> +#define MXL86110_EXT_SYNCE_CFG_EN_SYNC_E BIT(6)
> +#define MXL86110_EXT_SYNCE_CFG_CLK_SRC_SEL_MASK GENMASK(3, 1)
> +#define MXL86110_EXT_SYNCE_CFG_CLK_SRC_SEL_125M_PLL 0
> +#define MXL86110_EXT_SYNCE_CFG_CLK_SRC_SEL_25M 4
> +
> +/* WOL registers */
> +#define MXL86110_WOL_MAC_ADDR_HIGH_EXTD_REG 0xA007 /* high-> FF:FF */
> +#define MXL86110_WOL_MAC_ADDR_MIDDLE_EXTD_REG 0xA008 /* middle-> :FF:FF <-middle */
> +#define MXL86110_WOL_MAC_ADDR_LOW_EXTD_REG 0xA009 /* :FF:FF <-low */
> +
> +#define MXL86110_EXT_WOL_CFG_REG 0xA00A
> +#define MXL86110_EXT_WOL_CFG_WOLE_MASK BIT(3)
> +#define MXL86110_EXT_WOL_CFG_WOLE_DISABLE 0
> +#define MXL86110_EXT_WOL_CFG_WOLE_ENABLE BIT(3)
> +
> +/* RGMII register */
> +#define MXL86110_EXT_RGMII_CFG1_REG 0xA003
> +/* delay can be adjusted in steps of about 150ps */
> +#define MXL86110_EXT_RGMII_CFG1_RX_NO_DELAY (0x0 << 10)
> +/* Closest value to 2000 ps */
> +#define MXL86110_EXT_RGMII_CFG1_RX_DELAY_1950PS (0xD << 10)
> +#define MXL86110_EXT_RGMII_CFG1_RX_DELAY_MASK GENMASK(13, 10)
> +
> +#define MXL86110_EXT_RGMII_CFG1_TX_1G_DELAY_1950PS (0xD << 0)
> +#define MXL86110_EXT_RGMII_CFG1_TX_1G_DELAY_MASK GENMASK(3, 0)
> +
> +#define MXL86110_EXT_RGMII_CFG1_TX_10MB_100MB_DELAY_1950PS (0xD << 4)
> +#define MXL86110_EXT_RGMII_CFG1_TX_10MB_100MB_DELAY_MASK GENMASK(7, 4)
> +
> +#define MXL86110_EXT_RGMII_CFG1_FULL_MASK \
> + ((MXL86110_EXT_RGMII_CFG1_RX_DELAY_MASK) | \
> + (MXL86110_EXT_RGMII_CFG1_TX_1G_DELAY_MASK) | \
> + (MXL86110_EXT_RGMII_CFG1_TX_10MB_100MB_DELAY_MASK))
> +
> +/* EXT Sleep Control register */
> +#define MXL86110_UTP_EXT_SLEEP_CTRL_REG 0x27
> +#define MXL86110_UTP_EXT_SLEEP_CTRL_EN_SLEEP_SW_OFF 0
> +#define MXL86110_UTP_EXT_SLEEP_CTRL_EN_SLEEP_SW_MASK BIT(15)
> +
> +/* RGMII In-Band Status and MDIO Configuration Register */
> +#define MXL86110_EXT_RGMII_MDIO_CFG 0xA005
> +#define MXL86110_EXT_RGMII_MDIO_CFG_EPA0_MASK GENMASK(6, 6)
> +#define MXL86110_EXT_RGMII_MDIO_CFG_EBA_MASK GENMASK(5, 5)
> +#define MXL86110_EXT_RGMII_MDIO_CFG_BA_MASK GENMASK(4, 0)
> +
> +#define MXL86110_MAX_LEDS 3
> +/* LED registers and defines */
> +#define MXL86110_LED0_CFG_REG 0xA00C
> +#define MXL86110_LED1_CFG_REG 0xA00D
> +#define MXL86110_LED2_CFG_REG 0xA00E
> +
> +#define MXL86110_LEDX_CFG_TRAFFIC_ACT_BLINK_IND BIT(13)
> +#define MXL86110_LEDX_CFG_LINK_UP_FULL_DUPLEX_ON BIT(12)
> +#define MXL86110_LEDX_CFG_LINK_UP_HALF_DUPLEX_ON BIT(11)
> +#define MXL86110_LEDX_CFG_LINK_UP_TX_ACT_ON BIT(10) /* LED 0,1,2 default */
> +#define MXL86110_LEDX_CFG_LINK_UP_RX_ACT_ON BIT(9) /* LED 0,1,2 default */
> +#define MXL86110_LEDX_CFG_LINK_UP_TX_ON BIT(8)
> +#define MXL86110_LEDX_CFG_LINK_UP_RX_ON BIT(7)
> +#define MXL86110_LEDX_CFG_LINK_UP_1GB_ON BIT(6) /* LED 2 default */
> +#define MXL86110_LEDX_CFG_LINK_UP_100MB_ON BIT(5) /* LED 1 default */
> +#define MXL86110_LEDX_CFG_LINK_UP_10MB_ON BIT(4) /* LED 0 default */
> +#define MXL86110_LEDX_CFG_LINK_UP_COLLISION BIT(3)
> +#define MXL86110_LEDX_CFG_LINK_UP_1GB_BLINK BIT(2)
> +#define MXL86110_LEDX_CFG_LINK_UP_100MB_BLINK BIT(1)
> +#define MXL86110_LEDX_CFG_LINK_UP_10MB_BLINK BIT(0)
> +
> +#define MXL86110_LED_BLINK_CFG_REG 0xA00F
> +#define MXL86110_LED_BLINK_CFG_FREQ_MODE1_2HZ 0
> +#define MXL86110_LED_BLINK_CFG_FREQ_MODE1_4HZ BIT(0)
> +#define MXL86110_LED_BLINK_CFG_FREQ_MODE1_8HZ BIT(1)
> +#define MXL86110_LED_BLINK_CFG_FREQ_MODE1_16HZ (BIT(1) | BIT(0))
> +#define MXL86110_LED_BLINK_CFG_FREQ_MODE2_2HZ 0
> +#define MXL86110_LED_BLINK_CFG_FREQ_MODE2_4HZ BIT(2)
> +#define MXL86110_LED_BLINK_CFG_FREQ_MODE2_8HZ BIT(3)
> +#define MXL86110_LED_BLINK_CFG_FREQ_MODE2_16HZ (BIT(3) | BIT(2))
> +#define MXL86110_LED_BLINK_CFG_DUTY_CYCLE_50_PERC_ON 0
> +#define MXL86110_LED_BLINK_CFG_DUTY_CYCLE_67_PERC_ON (BIT(4))
> +#define MXL86110_LED_BLINK_CFG_DUTY_CYCLE_75_PERC_ON (BIT(5))
> +#define MXL86110_LED_BLINK_CFG_DUTY_CYCLE_83_PERC_ON (BIT(5) | BIT(4))
> +#define MXL86110_LED_BLINK_CFG_DUTY_CYCLE_50_PERC_OFF (BIT(6))
> +#define MXL86110_LED_BLINK_CFG_DUTY_CYCLE_33_PERC_ON (BIT(6) | BIT(4))
> +#define MXL86110_LED_BLINK_CFG_DUTY_CYCLE_25_PERC_ON (BIT(6) | BIT(5))
> +#define MXL86110_LED_BLINK_CFG_DUTY_CYCLE_17_PERC_ON (BIT(6) | BIT(5) | BIT(4))
> +
> +/* Chip Configuration Register - COM_EXT_CHIP_CFG */
> +#define MXL86110_EXT_CHIP_CFG_REG 0xA001
> +#define MXL86110_EXT_CHIP_CFG_RXDLY_ENABLE BIT(8)
> +#define MXL86110_EXT_CHIP_CFG_SW_RST_N_MODE BIT(15)
> +
> +/**
> + * mxl86110_write_extended_reg() - write to a PHY's extended register
> + * @phydev: pointer to a &struct phy_device
> + * @regnum: register number to write
> + * @val: value to write to @regnum
> + *
> + * NOTE: This function assumes the caller already holds the MDIO bus lock
> + * or otherwise has exclusive access to the PHY.
> + *
> + * returns 0 or negative error code
> + */
> +static int mxl86110_write_extended_reg(struct phy_device *phydev, u16 regnum, u16 val)
> +{
> + int ret;
> +
> + ret = __phy_write(phydev, MXL86110_EXTD_REG_ADDR_OFFSET, regnum);
> + if (ret < 0)
> + return ret;
> +
> + return __phy_write(phydev, MXL86110_EXTD_REG_ADDR_DATA, val);
> +}
> +
> +/**
> + * mxl86110_read_extended_reg - Read a PHY's extended register
> + * @phydev: Pointer to the PHY device structure
> + * @regnum: Extended register number to read (address written to reg 30)
> + *
> + * Reads the content of a PHY extended register using the MaxLinear
> + * 2-step access mechanism: write the register address to reg 30 (0x1E),
> + * then read the value from reg 31 (0x1F).
> + *
> + * NOTE: This function assumes the caller already holds the MDIO bus lock
> + * or otherwise has exclusive access to the PHY.
> + *
> + * Return: 16-bit register value on success, or negative errno code on failure.
> + */
> +static int mxl86110_read_extended_reg(struct phy_device *phydev, u16 regnum)
> +{
> + int ret;
> +
> + ret = __phy_write(phydev, MXL86110_EXTD_REG_ADDR_OFFSET, regnum);
> + if (ret < 0)
> + return ret;
> + return __phy_read(phydev, MXL86110_EXTD_REG_ADDR_DATA);
> +}
> +
> +/**
> + * mxl86110_modify_extended_reg() - modify bits of a PHY's extended register
> + * @phydev: pointer to the phy_device
> + * @regnum: register number to write
> + * @mask: bit mask of bits to clear
> + * @set: bit mask of bits to set
> + *
> + * NOTE: register value = (old register value & ~mask) | set.
> + * This function assumes the caller already holds the MDIO bus lock
> + * or otherwise has exclusive access to the PHY.
> + *
> + * returns 0 or negative error code
> + */
> +static int mxl86110_modify_extended_reg(struct phy_device *phydev, u16 regnum, u16 mask,
> + u16 set)
> +{
> + int ret;
> +
> + ret = __phy_write(phydev, MXL86110_EXTD_REG_ADDR_OFFSET, regnum);
> + if (ret < 0)
> + return ret;
> +
> + return __phy_modify(phydev, MXL86110_EXTD_REG_ADDR_DATA, mask, set);
> +}
> +
> +/**
> + * mxl86110_get_wol() - report if wake-on-lan is enabled
> + * @phydev: pointer to the phy_device
> + * @wol: a pointer to a &struct ethtool_wolinfo
> + */
> +static void mxl86110_get_wol(struct phy_device *phydev, struct ethtool_wolinfo *wol)
> +{
> + int value;
> +
> + wol->supported = WAKE_MAGIC;
> + wol->wolopts = 0;
> + phy_lock_mdio_bus(phydev);
> + value = mxl86110_read_extended_reg(phydev, MXL86110_EXT_WOL_CFG_REG);
> + phy_unlock_mdio_bus(phydev);
> + if (value >= 0 && (value & MXL86110_EXT_WOL_CFG_WOLE_MASK))
> + wol->wolopts |= WAKE_MAGIC;
> +}
> +
> +/**
> + * mxl86110_set_wol() - enable/disable wake-on-lan
> + * @phydev: pointer to the phy_device
> + * @wol: a pointer to a &struct ethtool_wolinfo
> + *
> + * Configures the WOL Magic Packet MAC
> + * returns 0 or negative errno code
> + */
> +static int mxl86110_set_wol(struct phy_device *phydev, struct ethtool_wolinfo *wol)
> +{
> + struct net_device *netdev;
> + const u8 *mac;
> + int ret = 0;
> +
> + phy_lock_mdio_bus(phydev);
> +
> + if (wol->wolopts & WAKE_MAGIC) {
> + netdev = phydev->attached_dev;
> + if (!netdev) {
> + ret = -ENODEV;
> + goto error;
> + }
> +
> + /* Configure the MAC address of the WOL magic packet */
> + mac = (const u8 *)netdev->dev_addr;
> + ret = mxl86110_write_extended_reg(phydev, MXL86110_WOL_MAC_ADDR_HIGH_EXTD_REG,
> + ((mac[0] << 8) | mac[1]));
> + if (ret < 0)
> + goto error;
> +
> + ret = mxl86110_write_extended_reg(phydev, MXL86110_WOL_MAC_ADDR_MIDDLE_EXTD_REG,
> + ((mac[2] << 8) | mac[3]));
> + if (ret < 0)
> + goto error;
> +
> + ret = mxl86110_write_extended_reg(phydev, MXL86110_WOL_MAC_ADDR_LOW_EXTD_REG,
> + ((mac[4] << 8) | mac[5]));
> + if (ret < 0)
> + goto error;
> +
> + ret = mxl86110_modify_extended_reg(phydev, MXL86110_EXT_WOL_CFG_REG,
> + MXL86110_EXT_WOL_CFG_WOLE_MASK,
> + MXL86110_EXT_WOL_CFG_WOLE_ENABLE);
> + if (ret < 0)
> + goto error;
> +
> + /* Enables Wake-on-LAN interrupt in the PHY. */
> + ret = __phy_modify(phydev, PHY_IRQ_ENABLE_REG, 0,
> + PHY_IRQ_ENABLE_REG_WOL);
> + if (ret < 0)
> + goto error;
> +
> + phydev_dbg(phydev, "%s, WOL Magic packet MAC: %02X:%02X:%02X:%02X:%02X:%02X\n",
> + __func__, mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]);
> +
> + } else {
> + ret = mxl86110_modify_extended_reg(phydev, MXL86110_EXT_WOL_CFG_REG,
> + MXL86110_EXT_WOL_CFG_WOLE_MASK,
> + MXL86110_EXT_WOL_CFG_WOLE_DISABLE);
> + if (ret < 0)
> + goto error;
> +
> + /* Disables Wake-on-LAN interrupt in the PHY. */
> + ret = __phy_modify(phydev, PHY_IRQ_ENABLE_REG,
> + PHY_IRQ_ENABLE_REG_WOL, 0);
> + if (ret < 0)
> + goto error;
> + }
> +
> + phy_unlock_mdio_bus(phydev);
> + return 0;
> +error:
> + phy_unlock_mdio_bus(phydev);
> + return ret;
> +}
> +
> +static const unsigned long supported_triggers = (BIT(TRIGGER_NETDEV_LINK_10) |
> + BIT(TRIGGER_NETDEV_LINK_100) |
> + BIT(TRIGGER_NETDEV_LINK_1000) |
> + BIT(TRIGGER_NETDEV_HALF_DUPLEX) |
> + BIT(TRIGGER_NETDEV_FULL_DUPLEX) |
> + BIT(TRIGGER_NETDEV_TX) |
> + BIT(TRIGGER_NETDEV_RX));
> +
> +static int mxl86110_led_hw_is_supported(struct phy_device *phydev, u8 index,
> + unsigned long rules)
> +{
> + if (index >= MXL86110_MAX_LEDS)
> + return -EINVAL;
> +
> + /* All combinations of the supported triggers are allowed */
> + if (rules & ~supported_triggers)
> + return -EOPNOTSUPP;
> +
> + return 0;
> +}
> +
> +static int mxl86110_led_hw_control_get(struct phy_device *phydev, u8 index,
> + unsigned long *rules)
> +{
> + u16 val;
> +
> + if (index >= MXL86110_MAX_LEDS)
> + return -EINVAL;
> +
> + phy_lock_mdio_bus(phydev);
> + val = mxl86110_read_extended_reg(phydev, MXL86110_LED0_CFG_REG + index);
> + phy_unlock_mdio_bus(phydev);
> + if (val < 0)
> + return val;
> +
> + if (val & MXL86110_LEDX_CFG_LINK_UP_TX_ACT_ON)
> + *rules |= BIT(TRIGGER_NETDEV_TX);
> +
> + if (val & MXL86110_LEDX_CFG_LINK_UP_RX_ACT_ON)
> + *rules |= BIT(TRIGGER_NETDEV_RX);
> +
> + if (val & MXL86110_LEDX_CFG_LINK_UP_HALF_DUPLEX_ON)
> + *rules |= BIT(TRIGGER_NETDEV_HALF_DUPLEX);
> +
> + if (val & MXL86110_LEDX_CFG_LINK_UP_FULL_DUPLEX_ON)
> + *rules |= BIT(TRIGGER_NETDEV_FULL_DUPLEX);
> +
> + if (val & MXL86110_LEDX_CFG_LINK_UP_10MB_ON)
> + *rules |= BIT(TRIGGER_NETDEV_LINK_10);
> +
> + if (val & MXL86110_LEDX_CFG_LINK_UP_100MB_ON)
> + *rules |= BIT(TRIGGER_NETDEV_LINK_100);
> +
> + if (val & MXL86110_LEDX_CFG_LINK_UP_1GB_ON)
> + *rules |= BIT(TRIGGER_NETDEV_LINK_1000);
> +
> + return 0;
> +};
> +
> +static int mxl86110_led_hw_control_set(struct phy_device *phydev, u8 index,
> + unsigned long rules)
> +{
> + u16 val = 0;
> + int ret;
> +
> + if (index >= MXL86110_MAX_LEDS)
> + return -EINVAL;
> +
> + if (rules & BIT(TRIGGER_NETDEV_LINK_10))
> + val |= MXL86110_LEDX_CFG_LINK_UP_10MB_ON;
> +
> + if (rules & BIT(TRIGGER_NETDEV_LINK_100))
> + val |= MXL86110_LEDX_CFG_LINK_UP_100MB_ON;
> +
> + if (rules & BIT(TRIGGER_NETDEV_LINK_1000))
> + val |= MXL86110_LEDX_CFG_LINK_UP_1GB_ON;
> +
> + if (rules & BIT(TRIGGER_NETDEV_TX))
> + val |= MXL86110_LEDX_CFG_LINK_UP_TX_ACT_ON;
> +
> + if (rules & BIT(TRIGGER_NETDEV_RX))
> + val |= MXL86110_LEDX_CFG_LINK_UP_RX_ACT_ON;
> +
> + if (rules & BIT(TRIGGER_NETDEV_HALF_DUPLEX))
> + val |= MXL86110_LEDX_CFG_LINK_UP_HALF_DUPLEX_ON;
> +
> + if (rules & BIT(TRIGGER_NETDEV_FULL_DUPLEX))
> + val |= MXL86110_LEDX_CFG_LINK_UP_FULL_DUPLEX_ON;
> +
> + if (rules & BIT(TRIGGER_NETDEV_TX) ||
> + rules & BIT(TRIGGER_NETDEV_RX))
> + val |= MXL86110_LEDX_CFG_TRAFFIC_ACT_BLINK_IND;
> +
> + phy_lock_mdio_bus(phydev);
> + ret = mxl86110_write_extended_reg(phydev, MXL86110_LED0_CFG_REG + index, val);
> + phy_unlock_mdio_bus(phydev);
> + if (ret)
> + return ret;
> +
> + return 0;
> +};
> +
> +/**
> + * mxl86110_synce_clk_cfg() - applies syncE/clk output configuration
> + * @phydev: pointer to the phy_device
> + *
> + * Custom settings can be defined in custom config section of the driver
> + * returns 0 or negative errno code
> + */
> +static int mxl86110_synce_clk_cfg(struct phy_device *phydev)
> +{
> + u16 mask = 0, value = 0;
> + int ret = 0;
> +
> + /*
> + * Configures the clock output to its default setting as per the datasheet.
> + * This results in a 25MHz clock output being selected in the
> + * COM_EXT_SYNCE_CFG register for SyncE configuration.
> + */
> + value = MXL86110_EXT_SYNCE_CFG_EN_SYNC_E |
> + FIELD_PREP(MXL86110_EXT_SYNCE_CFG_CLK_SRC_SEL_MASK,
> + MXL86110_EXT_SYNCE_CFG_CLK_SRC_SEL_25M);
> + mask = MXL86110_EXT_SYNCE_CFG_EN_SYNC_E |
> + MXL86110_EXT_SYNCE_CFG_CLK_SRC_SEL_MASK |
> + MXL86110_EXT_SYNCE_CFG_CLK_FRE_SEL;
> +
> + /* Write clock output configuration */
> + ret = mxl86110_modify_extended_reg(phydev, MXL86110_EXT_SYNCE_CFG_REG,
> + mask, value);
> +
> + return ret;
> +}
> +
> +/**
> + * mxl86110_broadcast_cfg - Configure MDIO broadcast setting for PHY
> + * @phydev: Pointer to the PHY device structure
> + *
> + * This function configures the MDIO broadcast behavior of the MxL86110 PHY.
> + * Currently, broadcast mode is explicitly disabled by clearing the EPA0 bit
> + * in the RGMII_MDIO_CFG extended register.
> + *
> + * Return: 0 on success or a negative errno code on failure.
> + */
> +static int mxl86110_broadcast_cfg(struct phy_device *phydev)
> +{
> + int ret = 0;
> + u16 val;
> +
> + val = mxl86110_read_extended_reg(phydev, MXL86110_EXT_RGMII_MDIO_CFG);
> + if (val < 0)
> + return val;
> +
> + val &= ~MXL86110_EXT_RGMII_MDIO_CFG_EPA0_MASK;
> + ret = mxl86110_write_extended_reg(phydev, MXL86110_EXT_RGMII_MDIO_CFG, val);
> +
> + return ret;
> +}
> +
> +/**
> + * mxl86110_enable_led_activity_blink - Enable LEDs activity blink on PHY
> + * @phydev: Pointer to the PHY device structure
> + *
> + * Configure all PHY LEDs to blink on traffic activity regardless of their
> + * ON or OFF state. This behavior allows each LED to serve as a pure activity
> + * indicator, independently of its use as a link status indicator.
> + *
> + * By default, each LED blinks only when it is also in the ON state. This function
> + * modifies the appropriate registers (LABx fields) to enable blinking even
> + * when the LEDs are OFF, to allow the LED to be used as a traffic indicator
> + * without requiring it to also serve as a link status LED.
> + *
> + * NOTE: Any further LED customization can be performed via the
> + * /sys/class/led interface; the functions led_hw_is_supported, led_hw_control_get, and
> + * led_hw_control_set are used to support this mechanism.
> + *
> + * Return: 0 on success or a negative errno code on failure.
> + */
> +static int mxl86110_enable_led_activity_blink(struct phy_device *phydev)
> +{
> + int ret, index;
> + u16 val = 0;
> +
> + for (index = 0; index < MXL86110_MAX_LEDS; index++) {
> + val = mxl86110_read_extended_reg(phydev, MXL86110_LED0_CFG_REG + index);
> + if (val < 0)
> + return val;
> +
> + val |= MXL86110_LEDX_CFG_TRAFFIC_ACT_BLINK_IND;
> + ret = mxl86110_write_extended_reg(phydev, MXL86110_LED0_CFG_REG + index, val);
> + if (ret < 0)
> + return ret;
> + }
> +
> + return 0;
> +};
> +
> +/**
> + * mxl86110_config_init() - initialize the PHY
> + * @phydev: pointer to the phy_device
> + *
> + * returns 0 or negative errno code
> + */
> +static int mxl86110_config_init(struct phy_device *phydev)
> +{
> + unsigned int val = 0;
> + int ret;
> +
> + phy_lock_mdio_bus(phydev);
> +
> + /* configure syncE / clk output */
> + ret = mxl86110_synce_clk_cfg(phydev);
> + if (ret < 0)
> + goto error;
> +
> + switch (phydev->interface) {
> + case PHY_INTERFACE_MODE_RGMII:
> + val = 0;
> + break;
> + case PHY_INTERFACE_MODE_RGMII_RXID:
> + val = MXL86110_EXT_RGMII_CFG1_RX_DELAY_1950PS;
> + break;
> + case PHY_INTERFACE_MODE_RGMII_TXID:
> + val = MXL86110_EXT_RGMII_CFG1_TX_1G_DELAY_1950PS |
> + MXL86110_EXT_RGMII_CFG1_TX_10MB_100MB_DELAY_1950PS;
> + break;
> + case PHY_INTERFACE_MODE_RGMII_ID:
> + val = MXL86110_EXT_RGMII_CFG1_TX_1G_DELAY_1950PS |
> + MXL86110_EXT_RGMII_CFG1_TX_10MB_100MB_DELAY_1950PS;
> + val |= MXL86110_EXT_RGMII_CFG1_RX_DELAY_1950PS;
> + break;
> + default:
> + ret = -EINVAL;
> + goto error;
> + }
> + ret = mxl86110_modify_extended_reg(phydev, MXL86110_EXT_RGMII_CFG1_REG,
> + MXL86110_EXT_RGMII_CFG1_FULL_MASK, val);
> + if (ret < 0)
> + goto error;
> +
> + /* Configure RXDLY (RGMII Rx Clock Delay) to disable the default additional
> + * delay value on RX_CLK (2 ns for 125 MHz, 8 ns for 25 MHz/2.5 MHz)
> + * and use just the digital one selected before
> + */
> + ret = mxl86110_modify_extended_reg(phydev, MXL86110_EXT_CHIP_CFG_REG,
> + MXL86110_EXT_CHIP_CFG_RXDLY_ENABLE, 0);
> + if (ret < 0)
> + goto error;
> +
> + ret = mxl86110_enable_led_activity_blink(phydev);
> + if (ret < 0)
> + goto error;
> +
> + ret = mxl86110_broadcast_cfg(phydev);
> + if (ret < 0)
> + goto error;
> +
> + phy_unlock_mdio_bus(phydev);
> + return 0;
> +error:
> + phy_unlock_mdio_bus(phydev);
> + return ret;
> +}
> +
> +static struct phy_driver mxl_phy_drvs[] = {
> + {
> + PHY_ID_MATCH_EXACT(PHY_ID_MXL86110),
> + .name = "MXL86110 Gigabit Ethernet",
> + .config_init = mxl86110_config_init,
> + .get_wol = mxl86110_get_wol,
> + .set_wol = mxl86110_set_wol,
> + .led_hw_is_supported = mxl86110_led_hw_is_supported,
> + .led_hw_control_get = mxl86110_led_hw_control_get,
> + .led_hw_control_set = mxl86110_led_hw_control_set,
> + },
> +};
> +
> +module_phy_driver(mxl_phy_drvs);
> +
> +static const struct mdio_device_id __maybe_unused mxl_tbl[] = {
> + { PHY_ID_MATCH_EXACT(PHY_ID_MXL86110) },
> + { }
> +};
> +
> +MODULE_DEVICE_TABLE(mdio, mxl_tbl);
> +
> +MODULE_DESCRIPTION("MaxLinear MXL86110 PHY driver");
> +MODULE_AUTHOR("Stefano Radaelli");
> +MODULE_LICENSE("GPL");
>
> base-commit: 894fbb55e60cab4ea740f6c65a08b5f8155221f4
> --
> 2.43.0
>
© 2016 - 2025 Red Hat, Inc.