1. Patchew
  2. linux
  3. [PATCH v1 0/4] Fix dtbs_check warnings in sensor overlays
  4. View patch

[PATCH v1 4/4] arm64: dts: ti: k3-am62x: Add required voltage supplies for TEVI-OV5640

Rishikesh Donadkar posted 4 patches 9 months, 2 weeks ago
There is a newer version of this series
[PATCH v1 4/4] arm64: dts: ti: k3-am62x: Add required voltage supplies for TEVI-OV5640
Posted by Rishikesh Donadkar 9 months, 2 weeks ago 
The device tree overlay for TEVI-OV5640 requires following voltage
supplies:

AVDD-supply: Analog voltage supply, 2.8 volts
DOVDD-supply: Digital I/O voltage supply, 1.8 volts
DVDD-supply: Digital core voltage supply, 1.5 volts

Add them in the DT overlay.

Signed-off-by: Rishikesh Donadkar <r-donadkar@ti.com>
---
 .../dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso  | 32 +++++++++++++++++++
 1 file changed, 32 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso b/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso
index b6bfdfbbdd984..123ab0e5e8dfa 100644
--- a/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso
+++ b/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso
@@ -15,6 +15,33 @@ clk_ov5640_fixed: ov5640-xclk {
 		#clock-cells = <0>;
 		clock-frequency = <24000000>;
 	};
+
+	reg_2p8v: regulator-2p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P8V";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		vin-supply = <&vcc_3v3_sys>;
+		regulator-always-on;
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3_sys>;
+		regulator-always-on;
+	};
+
+	reg_1p5v: regulator-1p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P5V";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		vin-supply = <&vcc_3v3_sys>;
+		regulator-always-on;
+	};
 };
 
 &main_i2c2 {
@@ -40,6 +67,11 @@ ov5640: camera@3c {
 
 				clocks = <&clk_ov5640_fixed>;
 				clock-names = "xclk";
+
+				AVDD-supply = <&reg_2p8v>;
+				DOVDD-supply = <&reg_1p8v>;
+				DVDD-supply = <&reg_1p5v>;
+
 				powerdown-gpios = <&exp1 13 GPIO_ACTIVE_LOW>;
 
 				port {
-- 
2.34.1
Re: [PATCH v1 4/4] arm64: dts: ti: k3-am62x: Add required voltage supplies for TEVI-OV5640
Posted by Devarsh Thakkar 9 months, 1 week ago 

On 29/04/25 21:11, Rishikesh Donadkar wrote:
> The device tree overlay for TEVI-OV5640 requires following voltage
> supplies:
> 
> AVDD-supply: Analog voltage supply, 2.8 volts
> DOVDD-supply: Digital I/O voltage supply, 1.8 volts
> DVDD-supply: Digital core voltage supply, 1.5 volts
> 

I think this contradicts the voltage mentioned in TEVI-OV56540 doc [1]
which mention digital voltage as 3.3 volts ?

> Add them in the DT overlay.
> 

[1]:
https://www.technexion.com/wp-content/uploads/2023/09/product-brief_tevi-ov5640.pdf

Regards
Devarsh
> Signed-off-by: Rishikesh Donadkar <r-donadkar@ti.com>
> ---
>  .../dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso  | 32 +++++++++++++++++++
>  1 file changed, 32 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso b/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso
> index b6bfdfbbdd984..123ab0e5e8dfa 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso
> +++ b/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso
> @@ -15,6 +15,33 @@ clk_ov5640_fixed: ov5640-xclk {
>  		#clock-cells = <0>;
>  		clock-frequency = <24000000>;
>  	};
> +
> +	reg_2p8v: regulator-2p8v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "2P8V";
> +		regulator-min-microvolt = <2800000>;
> +		regulator-max-microvolt = <2800000>;
> +		vin-supply = <&vcc_3v3_sys>;
> +		regulator-always-on;
> +	};
> +
> +	reg_1p8v: regulator-1p8v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "1P8V";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		vin-supply = <&vcc_3v3_sys>;
> +		regulator-always-on;
> +	};
> +
> +	reg_1p5v: regulator-1p5v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "1P5V";
> +		regulator-min-microvolt = <1500000>;
> +		regulator-max-microvolt = <1500000>;
> +		vin-supply = <&vcc_3v3_sys>;
> +		regulator-always-on;
> +	};
>  };
>  
>  &main_i2c2 {
> @@ -40,6 +67,11 @@ ov5640: camera@3c {
>  
>  				clocks = <&clk_ov5640_fixed>;
>  				clock-names = "xclk";
> +
> +				AVDD-supply = <&reg_2p8v>;
> +				DOVDD-supply = <&reg_1p8v>;
> +				DVDD-supply = <&reg_1p5v>;
> +
>  				powerdown-gpios = <&exp1 13 GPIO_ACTIVE_LOW>;
>  
>  				port {
Re: [PATCH v1 4/4] arm64: dts: ti: k3-am62x: Add required voltage supplies for TEVI-OV5640
Posted by Donadkar, Rishikesh 9 months, 1 week ago 
On 02-05-2025 14:37, Devarsh Thakkar wrote:
>
> On 29/04/25 21:11, Rishikesh Donadkar wrote:
>> The device tree overlay for TEVI-OV5640 requires following voltage
>> supplies:
>>
>> AVDD-supply: Analog voltage supply, 2.8 volts
>> DOVDD-supply: Digital I/O voltage supply, 1.8 volts
>> DVDD-supply: Digital core voltage supply, 1.5 volts
>>
> I think this contradicts the voltage mentioned in TEVI-OV56540 doc [1]
> which mention digital voltage as 3.3 volts ?


Thank you for pointing out, I will fix it.

>
>> Add them in the DT overlay.
>>
> [1]:
> https://www.technexion.com/wp-content/uploads/2023/09/product-brief_tevi-ov5640.pdf
>
> Regards
> Devarsh
>> Signed-off-by: Rishikesh Donadkar <r-donadkar@ti.com>
>> ---
>>   .../dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso  | 32 +++++++++++++++++++
>>   1 file changed, 32 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso b/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso
>> index b6bfdfbbdd984..123ab0e5e8dfa 100644
>> --- a/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso
>> +++ b/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso
>> @@ -15,6 +15,33 @@ clk_ov5640_fixed: ov5640-xclk {
>>   		#clock-cells = <0>;
>>   		clock-frequency = <24000000>;
>>   	};
>> +
>> +	reg_2p8v: regulator-2p8v {
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "2P8V";
>> +		regulator-min-microvolt = <2800000>;
>> +		regulator-max-microvolt = <2800000>;
>> +		vin-supply = <&vcc_3v3_sys>;
>> +		regulator-always-on;
>> +	};
>> +
>> +	reg_1p8v: regulator-1p8v {
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "1P8V";
>> +		regulator-min-microvolt = <1800000>;
>> +		regulator-max-microvolt = <1800000>;
>> +		vin-supply = <&vcc_3v3_sys>;
>> +		regulator-always-on;
>> +	};
>> +
>> +	reg_1p5v: regulator-1p5v {
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "1P5V";
>> +		regulator-min-microvolt = <1500000>;
>> +		regulator-max-microvolt = <1500000>;
>> +		vin-supply = <&vcc_3v3_sys>;
>> +		regulator-always-on;
>> +	};
>>   };
>>   
>>   &main_i2c2 {
>> @@ -40,6 +67,11 @@ ov5640: camera@3c {
>>   
>>   				clocks = <&clk_ov5640_fixed>;
>>   				clock-names = "xclk";
>> +
>> +				AVDD-supply = <&reg_2p8v>;
>> +				DOVDD-supply = <&reg_1p8v>;
>> +				DVDD-supply = <&reg_1p5v>;
>> +
>>   				powerdown-gpios = <&exp1 13 GPIO_ACTIVE_LOW>;
>>   
>>   				port {

Patchew 2.1-devel-b67e4c2

© 2016 - 2026 Red Hat, Inc.