From: Qiang Yu <quic_qianyu@quicinc.com>

Add perst, wake and clkreq sideband signals and required regulators in
PCIe3 controller and PHY device tree node. Describe the voltage rails of
the x8 PCI slots for PCIe3 port.

Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Signed-off-by: Wenbin Yao <quic_wenbyao@quicinc.com>
---
 arch/arm64/boot/dts/qcom/x1e80100-qcp.dts | 118 ++++++++++++++++++++++
 1 file changed, 118 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
index 470c4f826..88dfd2199 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
+++ b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
@@ -318,6 +318,48 @@ vreg_wcn_3p3: regulator-wcn-3p3 {
 		regulator-boot-on;
 	};
 
+	vreg_pcie_12v: regulator-pcie-12v {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_PCIE_12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+
+		gpio = <&pm8550ve_8_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pcie_x8_12v>;
+	};
+
+	vreg_pcie_3v3_aux: regulator-pcie-3v3-aux {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_PCIE_3P3_AUX";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pmc8380_3_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pm_sde7_aux_3p3_en>;
+	};
+
+	vreg_pcie_3v3: regulator-pcie-3v3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_PCIE_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pmc8380_3_gpios 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pm_sde7_main_3p3_en>;
+};
+
 	usb-1-ss0-sbu-mux {
 		compatible = "onnn,fsusb42", "gpio-sbu-mux";
 
@@ -909,6 +951,59 @@ &mdss_dp3_phy {
 	status = "okay";
 };
 
+&pm8550ve_8_gpios {
+	pcie_x8_12v: pcie-12v-default-state {
+		pins = "gpio8";
+		function = "normal";
+		output-enable;
+		output-high;
+		bias-pull-down;
+		power-source = <0>;
+	};
+};
+
+&pmc8380_3_gpios {
+	pm_sde7_aux_3p3_en: pcie-aux-3p3-default-state {
+		pins = "gpio8";
+		function = "normal";
+		output-enable;
+		output-high;
+		bias-pull-down;
+		power-source = <0>;
+	};
+
+	pm_sde7_main_3p3_en: pcie-main-3p3-default-state {
+		pins = "gpio6";
+		function = "normal";
+		output-enable;
+		output-high;
+		bias-pull-down;
+		power-source = <0>;
+	};
+};
+
+&pcie3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie3_default>;
+	perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+};
+
+&pcie3_phy {
+	vdda-phy-supply = <&vreg_l3c_0p8>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&pcie3port {
+	vpcie12v-supply = <&vreg_pcie_12v>;
+	vpcie3v3-supply = <&vreg_pcie_3v3>;
+	vpcie3v3aux-supply = <&vreg_pcie_3v3_aux>;
+};
+
 &pcie4 {
 	perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
 	wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
@@ -1120,6 +1215,29 @@ nvme_reg_en: nvme-reg-en-state {
 		bias-disable;
 	};
 
+	pcie3_default: pcie3-default-state {
+		clkreq-n-pins {
+			pins = "gpio144";
+			function = "pcie3_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio143";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		wake-n-pins {
+			pins = "gpio145";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
 	pcie4_default: pcie4-default-state {
 		clkreq-n-pins {
 			pins = "gpio147";
-- 
2.34.1

On 4/25/25 11:29 AM, Wenbin Yao wrote:
> From: Qiang Yu <quic_qianyu@quicinc.com>
> 
> Add perst, wake and clkreq sideband signals and required regulators in
> PCIe3 controller and PHY device tree node. Describe the voltage rails of
> the x8 PCI slots for PCIe3 port.
> 
> Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
> Signed-off-by: Wenbin Yao <quic_wenbyao@quicinc.com>
> ---
>  arch/arm64/boot/dts/qcom/x1e80100-qcp.dts | 118 ++++++++++++++++++++++
>  1 file changed, 118 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
> index 470c4f826..88dfd2199 100644
> --- a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
> +++ b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
> @@ -318,6 +318,48 @@ vreg_wcn_3p3: regulator-wcn-3p3 {
>  		regulator-boot-on;
>  	};
>  
> +	vreg_pcie_12v: regulator-pcie-12v {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "VREG_PCIE_12V";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +
> +		gpio = <&pm8550ve_8_gpios 8 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pcie_x8_12v>;

Please keep the 

property-n
property-names

order

throughout the patch

with that:

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad