1. Patchew
  2. linux
  3. View series

[RESEND v2] mmc: mtk-sd: Add condition to enable 'single' burst type

Axe Yang posted 1 patch 4 weeks, 1 day ago 
drivers/mmc/host/mtk-sd.c | 16 ++++++++++++----
1 file changed, 12 insertions(+), 4 deletions(-)
[RESEND v2] mmc: mtk-sd: Add condition to enable 'single' burst type
Posted by Axe Yang 4 weeks, 1 day ago 
This change add a condition for 'single' burst type selection.

Read AXI_LEN field from EMMC50_CFG2(AHB2AXI wrapper) register, if the
value is not 0, it means the HWIP is using AXI as AMBA bus, which do
not support 'single' burst type.

Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Axe Yang <axe.yang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
This change dependents on 'mmc: mtk-sd: Cleanups for register R/W':

https://patchwork.kernel.org/project/linux-mediatek/cover/20250325110701.52623-1-angelogioacchino.delregno@collabora.com/
---
 drivers/mmc/host/mtk-sd.c | 16 ++++++++++++----
 1 file changed, 12 insertions(+), 4 deletions(-)

diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
index ceeae1aeac94..2e4bd5166c17 100644
--- a/drivers/mmc/host/mtk-sd.c
+++ b/drivers/mmc/host/mtk-sd.c
@@ -84,6 +84,7 @@
 #define EMMC51_CFG0	 0x204
 #define EMMC50_CFG0      0x208
 #define EMMC50_CFG1      0x20c
+#define EMMC50_CFG2      0x21c
 #define EMMC50_CFG3      0x220
 #define SDC_FIFO_CFG     0x228
 #define CQHCI_SETTING	 0x7fc
@@ -306,7 +307,10 @@
 /* EMMC50_CFG1 mask */
 #define EMMC50_CFG1_DS_CFG        BIT(28)  /* RW */
 
-#define EMMC50_CFG3_OUTS_WR       GENMASK(4, 0)  /* RW */
+/* EMMC50_CFG2 mask */
+#define EMMC50_CFG2_AXI_SET_LEN   GENMASK(27, 24) /* RW */
+
+#define EMMC50_CFG3_OUTS_WR       GENMASK(4, 0)   /* RW */
 
 #define SDC_FIFO_CFG_WRVALIDSEL   BIT(24)  /* RW */
 #define SDC_FIFO_CFG_RDVALIDSEL   BIT(25)  /* RW */
@@ -1917,9 +1921,13 @@ static void msdc_init_hw(struct msdc_host *host)
 	pb1_val |= FIELD_PREP(MSDC_PATCH_BIT1_CMDTA, 1);
 	pb1_val |= MSDC_PB1_DDR_CMD_FIX_SEL;
 
-	/* Set single burst mode, auto sync state clear, block gap stop clk */
-	pb1_val |= MSDC_PB1_SINGLE_BURST | MSDC_PB1_RSVD20 |
-		   MSDC_PB1_AUTO_SYNCST_CLR | MSDC_PB1_MARK_POP_WATER;
+	/* Support 'single' burst type only when AXI_LEN is 0 */
+	sdr_get_field(host->base + EMMC50_CFG2, EMMC50_CFG2_AXI_SET_LEN, &val);
+	if (!val)
+		pb1_val |= MSDC_PB1_SINGLE_BURST;
+
+	/* Set auto sync state clear, block gap stop clk */
+	pb1_val |= MSDC_PB1_RSVD20 | MSDC_PB1_AUTO_SYNCST_CLR | MSDC_PB1_MARK_POP_WATER;
 
 	/* Set low power DCM, use HCLK for GDMA, use MSDC CLK for everything else */
 	pb1_val |= MSDC_PB1_LP_DCM_EN | MSDC_PB1_RSVD3 |
-- 
2.46.0
Re: [RESEND v2] mmc: mtk-sd: Add condition to enable 'single' burst type
Posted by Ulf Hansson 2 weeks, 4 days ago 
On Fri, 11 Apr 2025 at 07:41, Axe Yang <axe.yang@mediatek.com> wrote:
>
> This change add a condition for 'single' burst type selection.
>
> Read AXI_LEN field from EMMC50_CFG2(AHB2AXI wrapper) register, if the
> value is not 0, it means the HWIP is using AXI as AMBA bus, which do
> not support 'single' burst type.
>
> Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
> Signed-off-by: Axe Yang <axe.yang@mediatek.com>
> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Applied for next, thanks!

Kind regards
Uffe


> ---
> This change dependents on 'mmc: mtk-sd: Cleanups for register R/W':
>
> https://patchwork.kernel.org/project/linux-mediatek/cover/20250325110701.52623-1-angelogioacchino.delregno@collabora.com/
> ---
>  drivers/mmc/host/mtk-sd.c | 16 ++++++++++++----
>  1 file changed, 12 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
> index ceeae1aeac94..2e4bd5166c17 100644
> --- a/drivers/mmc/host/mtk-sd.c
> +++ b/drivers/mmc/host/mtk-sd.c
> @@ -84,6 +84,7 @@
>  #define EMMC51_CFG0     0x204
>  #define EMMC50_CFG0      0x208
>  #define EMMC50_CFG1      0x20c
> +#define EMMC50_CFG2      0x21c
>  #define EMMC50_CFG3      0x220
>  #define SDC_FIFO_CFG     0x228
>  #define CQHCI_SETTING   0x7fc
> @@ -306,7 +307,10 @@
>  /* EMMC50_CFG1 mask */
>  #define EMMC50_CFG1_DS_CFG        BIT(28)  /* RW */
>
> -#define EMMC50_CFG3_OUTS_WR       GENMASK(4, 0)  /* RW */
> +/* EMMC50_CFG2 mask */
> +#define EMMC50_CFG2_AXI_SET_LEN   GENMASK(27, 24) /* RW */
> +
> +#define EMMC50_CFG3_OUTS_WR       GENMASK(4, 0)   /* RW */
>
>  #define SDC_FIFO_CFG_WRVALIDSEL   BIT(24)  /* RW */
>  #define SDC_FIFO_CFG_RDVALIDSEL   BIT(25)  /* RW */
> @@ -1917,9 +1921,13 @@ static void msdc_init_hw(struct msdc_host *host)
>         pb1_val |= FIELD_PREP(MSDC_PATCH_BIT1_CMDTA, 1);
>         pb1_val |= MSDC_PB1_DDR_CMD_FIX_SEL;
>
> -       /* Set single burst mode, auto sync state clear, block gap stop clk */
> -       pb1_val |= MSDC_PB1_SINGLE_BURST | MSDC_PB1_RSVD20 |
> -                  MSDC_PB1_AUTO_SYNCST_CLR | MSDC_PB1_MARK_POP_WATER;
> +       /* Support 'single' burst type only when AXI_LEN is 0 */
> +       sdr_get_field(host->base + EMMC50_CFG2, EMMC50_CFG2_AXI_SET_LEN, &val);
> +       if (!val)
> +               pb1_val |= MSDC_PB1_SINGLE_BURST;
> +
> +       /* Set auto sync state clear, block gap stop clk */
> +       pb1_val |= MSDC_PB1_RSVD20 | MSDC_PB1_AUTO_SYNCST_CLR | MSDC_PB1_MARK_POP_WATER;
>
>         /* Set low power DCM, use HCLK for GDMA, use MSDC CLK for everything else */
>         pb1_val |= MSDC_PB1_LP_DCM_EN | MSDC_PB1_RSVD3 |
> --
> 2.46.0
>

Patchew 2.1-devel-b67e4c2

© 2016 - 2025 Red Hat, Inc.