1. Patchew
  2. linux
  3. [net-next v4 0/5] net: mtip: Add support for MTIP imx287 L2 switch driver
  4. View patch

[net-next v4 1/5] dt-bindings: net: Add MTIP L2 switch description

Lukasz Majewski posted 5 patches 10 months, 1 week ago
There is a newer version of this series
[net-next v4 1/5] dt-bindings: net: Add MTIP L2 switch description
Posted by Lukasz Majewski 10 months, 1 week ago 
This patch provides description of the MTIP L2 switch available in some
NXP's SOCs - e.g. imx287.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
---
Changes for v2:
- Rename the file to match exactly the compatible
  (nxp,imx287-mtip-switch)

Changes for v3:
- Remove '-' from const:'nxp,imx287-mtip-switch'
- Use '^port@[12]+$' for port patternProperties
- Drop status = "okay";
- Provide proper indentation for 'example' binding (replace 8
  spaces with 4 spaces)
- Remove smsc,disable-energy-detect; property
- Remove interrupt-parent and interrupts properties as not required
- Remove #address-cells and #size-cells from required properties check
- remove description from reg:
- Add $ref: ethernet-switch.yaml#

Changes for v4:
- Use $ref: ethernet-switch.yaml#/$defs/ethernet-ports and remove already
  referenced properties
- Rename file to nxp,imx28-mtip-switch.yaml
---
 .../bindings/net/nxp,imx28-mtip-switch.yaml   | 126 ++++++++++++++++++
 1 file changed, 126 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/nxp,imx28-mtip-switch.yaml

diff --git a/Documentation/devicetree/bindings/net/nxp,imx28-mtip-switch.yaml b/Documentation/devicetree/bindings/net/nxp,imx28-mtip-switch.yaml
new file mode 100644
index 000000000000..1afaf8029725
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/nxp,imx28-mtip-switch.yaml
@@ -0,0 +1,126 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/nxp,imx28-mtip-switch.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP SoC Ethernet Switch Controller (L2 MoreThanIP switch)
+
+maintainers:
+  - Lukasz Majewski <lukma@denx.de>
+
+description:
+  The 2-port switch ethernet subsystem provides ethernet packet (L2)
+  communication and can be configured as an ethernet switch. It provides the
+  reduced media independent interface (RMII), the management data input
+  output (MDIO) for physical layer device (PHY) management.
+
+$ref: ethernet-switch.yaml#/$defs/ethernet-ports
+
+patternProperties:
+  "^(ethernet-)?ports$":
+    type: object
+    additionalProperties: true
+
+properties:
+  compatible:
+    const: nxp,imx28-mtip-switch
+
+  reg:
+    maxItems: 1
+
+  phy-supply:
+    description:
+      Regulator that powers Ethernet PHYs.
+
+  clocks:
+    items:
+      - description: Register accessing clock
+      - description: Bus access clock
+      - description: Output clock for external device - e.g. PHY source clock
+      - description: IEEE1588 timer clock
+
+  clock-names:
+    items:
+      - const: ipg
+      - const: ahb
+      - const: enet_out
+      - const: ptp
+
+  interrupts:
+    items:
+      - description: Switch interrupt
+      - description: ENET0 interrupt
+      - description: ENET1 interrupt
+
+  pinctrl-names: true
+
+  mdio:
+    type: object
+    $ref: mdio.yaml#
+    unevaluatedProperties: false
+    description:
+      Specifies the mdio bus in the switch, used as a container for phy nodes.
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - interrupts
+  - mdio
+  - ethernet-ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include<dt-bindings/interrupt-controller/irq.h>
+    switch@800f0000 {
+        compatible = "nxp,imx28-mtip-switch";
+        reg = <0x800f0000 0x20000>;
+        pinctrl-names = "default";
+        pinctrl-0 = <&mac0_pins_a>, <&mac1_pins_a>;
+        phy-supply = <&reg_fec_3v3>;
+        interrupts = <100>, <101>, <102>;
+        clocks = <&clks 57>, <&clks 57>, <&clks 64>, <&clks 35>;
+        clock-names = "ipg", "ahb", "enet_out", "ptp";
+
+        ethernet-ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            mtip_port1: ethernet-port@1 {
+                reg = <1>;
+                label = "lan0";
+                local-mac-address = [ 00 00 00 00 00 00 ];
+                phy-mode = "rmii";
+                phy-handle = <&ethphy0>;
+            };
+
+            mtip_port2: ethernet-port@2 {
+                reg = <2>;
+                label = "lan1";
+                local-mac-address = [ 00 00 00 00 00 00 ];
+                phy-mode = "rmii";
+                phy-handle = <&ethphy1>;
+            };
+        };
+
+        mdio_sw: mdio {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            reset-gpios = <&gpio2 13 0>;
+            reset-delay-us = <25000>;
+            reset-post-delay-us = <10000>;
+
+            ethphy0: ethernet-phy@0 {
+                reg = <0>;
+            };
+
+            ethphy1: ethernet-phy@1 {
+                reg = <1>;
+            };
+        };
+    };
-- 
2.39.5
Re: [net-next v4 1/5] dt-bindings: net: Add MTIP L2 switch description
Posted by Rob Herring 10 months ago 
On Mon, Apr 07, 2025 at 04:51:53PM +0200, Lukasz Majewski wrote:
> This patch provides description of the MTIP L2 switch available in some
> NXP's SOCs - e.g. imx287.
> 
> Signed-off-by: Lukasz Majewski <lukma@denx.de>
> ---
> Changes for v2:
> - Rename the file to match exactly the compatible
>   (nxp,imx287-mtip-switch)
> 
> Changes for v3:
> - Remove '-' from const:'nxp,imx287-mtip-switch'
> - Use '^port@[12]+$' for port patternProperties
> - Drop status = "okay";
> - Provide proper indentation for 'example' binding (replace 8
>   spaces with 4 spaces)
> - Remove smsc,disable-energy-detect; property
> - Remove interrupt-parent and interrupts properties as not required
> - Remove #address-cells and #size-cells from required properties check
> - remove description from reg:
> - Add $ref: ethernet-switch.yaml#
> 
> Changes for v4:
> - Use $ref: ethernet-switch.yaml#/$defs/ethernet-ports and remove already
>   referenced properties
> - Rename file to nxp,imx28-mtip-switch.yaml
> ---
>  .../bindings/net/nxp,imx28-mtip-switch.yaml   | 126 ++++++++++++++++++
>  1 file changed, 126 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/nxp,imx28-mtip-switch.yaml
> 
> diff --git a/Documentation/devicetree/bindings/net/nxp,imx28-mtip-switch.yaml b/Documentation/devicetree/bindings/net/nxp,imx28-mtip-switch.yaml
> new file mode 100644
> index 000000000000..1afaf8029725
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/nxp,imx28-mtip-switch.yaml
> @@ -0,0 +1,126 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/net/nxp,imx28-mtip-switch.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: NXP SoC Ethernet Switch Controller (L2 MoreThanIP switch)
> +
> +maintainers:
> +  - Lukasz Majewski <lukma@denx.de>
> +
> +description:
> +  The 2-port switch ethernet subsystem provides ethernet packet (L2)
> +  communication and can be configured as an ethernet switch. It provides the
> +  reduced media independent interface (RMII), the management data input
> +  output (MDIO) for physical layer device (PHY) management.
> +
> +$ref: ethernet-switch.yaml#/$defs/ethernet-ports
> +

> +patternProperties:
> +  "^(ethernet-)?ports$":

New bindings should only use 'ethernet-ports'.

> +    type: object
> +    additionalProperties: true

But what's this for? I thought you had some constrants for phy-mode and 
phy-handle?

> +
> +properties:
> +  compatible:
> +    const: nxp,imx28-mtip-switch
> +
> +  reg:
> +    maxItems: 1
> +
> +  phy-supply:
> +    description:
> +      Regulator that powers Ethernet PHYs.
> +
> +  clocks:
> +    items:
> +      - description: Register accessing clock
> +      - description: Bus access clock
> +      - description: Output clock for external device - e.g. PHY source clock
> +      - description: IEEE1588 timer clock
> +
> +  clock-names:
> +    items:
> +      - const: ipg
> +      - const: ahb
> +      - const: enet_out
> +      - const: ptp
> +
> +  interrupts:
> +    items:
> +      - description: Switch interrupt
> +      - description: ENET0 interrupt
> +      - description: ENET1 interrupt
> +
> +  pinctrl-names: true
> +
> +  mdio:
> +    type: object
> +    $ref: mdio.yaml#
> +    unevaluatedProperties: false
> +    description:
> +      Specifies the mdio bus in the switch, used as a container for phy nodes.
> +
> +required:
> +  - compatible
> +  - reg
> +  - clocks
> +  - clock-names
> +  - interrupts
> +  - mdio
> +  - ethernet-ports
> +
> +additionalProperties: false

unevaluatedProperties: false

> +
> +examples:
> +  - |
> +    #include<dt-bindings/interrupt-controller/irq.h>
> +    switch@800f0000 {
> +        compatible = "nxp,imx28-mtip-switch";
> +        reg = <0x800f0000 0x20000>;
> +        pinctrl-names = "default";
> +        pinctrl-0 = <&mac0_pins_a>, <&mac1_pins_a>;
> +        phy-supply = <&reg_fec_3v3>;
> +        interrupts = <100>, <101>, <102>;
> +        clocks = <&clks 57>, <&clks 57>, <&clks 64>, <&clks 35>;
> +        clock-names = "ipg", "ahb", "enet_out", "ptp";
> +
> +        ethernet-ports {
> +            #address-cells = <1>;
> +            #size-cells = <0>;
> +
> +            mtip_port1: ethernet-port@1 {
> +                reg = <1>;
> +                label = "lan0";
> +                local-mac-address = [ 00 00 00 00 00 00 ];
> +                phy-mode = "rmii";
> +                phy-handle = <&ethphy0>;
> +            };
> +
> +            mtip_port2: ethernet-port@2 {
> +                reg = <2>;
> +                label = "lan1";
> +                local-mac-address = [ 00 00 00 00 00 00 ];
> +                phy-mode = "rmii";
> +                phy-handle = <&ethphy1>;
> +            };
> +        };
> +
> +        mdio_sw: mdio {
> +            #address-cells = <1>;
> +            #size-cells = <0>;
> +
> +            reset-gpios = <&gpio2 13 0>;
> +            reset-delay-us = <25000>;
> +            reset-post-delay-us = <10000>;
> +
> +            ethphy0: ethernet-phy@0 {
> +                reg = <0>;
> +            };
> +
> +            ethphy1: ethernet-phy@1 {
> +                reg = <1>;
> +            };
> +        };
> +    };
> -- 
> 2.39.5
>
Re: [net-next v4 1/5] dt-bindings: net: Add MTIP L2 switch description
Posted by Lukasz Majewski 10 months ago 
Hi Rob,

> On Mon, Apr 07, 2025 at 04:51:53PM +0200, Lukasz Majewski wrote:
> > This patch provides description of the MTIP L2 switch available in
> > some NXP's SOCs - e.g. imx287.
> > 
> > Signed-off-by: Lukasz Majewski <lukma@denx.de>
> > ---
> > Changes for v2:
> > - Rename the file to match exactly the compatible
> >   (nxp,imx287-mtip-switch)
> > 
> > Changes for v3:
> > - Remove '-' from const:'nxp,imx287-mtip-switch'
> > - Use '^port@[12]+$' for port patternProperties
> > - Drop status = "okay";
> > - Provide proper indentation for 'example' binding (replace 8
> >   spaces with 4 spaces)
> > - Remove smsc,disable-energy-detect; property
> > - Remove interrupt-parent and interrupts properties as not required
> > - Remove #address-cells and #size-cells from required properties
> > check
> > - remove description from reg:
> > - Add $ref: ethernet-switch.yaml#
> > 
> > Changes for v4:
> > - Use $ref: ethernet-switch.yaml#/$defs/ethernet-ports and remove
> > already referenced properties
> > - Rename file to nxp,imx28-mtip-switch.yaml
> > ---
> >  .../bindings/net/nxp,imx28-mtip-switch.yaml   | 126
> > ++++++++++++++++++ 1 file changed, 126 insertions(+)
> >  create mode 100644
> > Documentation/devicetree/bindings/net/nxp,imx28-mtip-switch.yaml
> > 
> > diff --git
> > a/Documentation/devicetree/bindings/net/nxp,imx28-mtip-switch.yaml
> > b/Documentation/devicetree/bindings/net/nxp,imx28-mtip-switch.yaml
> > new file mode 100644 index 000000000000..1afaf8029725 --- /dev/null
> > +++
> > b/Documentation/devicetree/bindings/net/nxp,imx28-mtip-switch.yaml
> > @@ -0,0 +1,126 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR
> > BSD-2-Clause) +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/net/nxp,imx28-mtip-switch.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: NXP SoC Ethernet Switch Controller (L2 MoreThanIP switch)
> > +
> > +maintainers:
> > +  - Lukasz Majewski <lukma@denx.de>
> > +
> > +description:
> > +  The 2-port switch ethernet subsystem provides ethernet packet
> > (L2)
> > +  communication and can be configured as an ethernet switch. It
> > provides the
> > +  reduced media independent interface (RMII), the management data
> > input
> > +  output (MDIO) for physical layer device (PHY) management.
> > +
> > +$ref: ethernet-switch.yaml#/$defs/ethernet-ports
> > +  
> 
> > +patternProperties:
> > +  "^(ethernet-)?ports$":  
> 
> New bindings should only use 'ethernet-ports'.

Ok.

> 
> > +    type: object
> > +    additionalProperties: true  
> 
> But what's this for? I thought you had some constrants for phy-mode
> and phy-handle?
> 

I've prepared following changes:

--- a/Documentation/devicetree/bindings/net/nxp,imx28-mtip-switch.yaml
+++ b/Documentation/devicetree/bindings/net/nxp,imx28-mtip-switch.yaml
@@ -17,11 +17,6 @@ description:
 
 $ref: ethernet-switch.yaml#/$defs/ethernet-ports
 
-patternProperties:
-  "^(ethernet-)?ports$":
-    type: object
-    additionalProperties: true
-
 properties:
   compatible:
     const: nxp,imx28-mtip-switch
@@ -55,6 +50,26 @@ properties:
 
   pinctrl-names: true
 
+  ethernet-ports:
+    type: object
+    additionalProperties: true
+    properties:
+      ethernet-port:
+        type: object
+        unevaluatedProperties: false
+
+        properties:
+          reg:
+            items:
+              - enum: [1, 2]
+            description: MTIP L2 switch port number
+
+        required:
+          - reg
+          - label
+          - phy-mode
+          - phy-handle
+
   mdio:
     type: object
     $ref: mdio.yaml#
@@ -71,7 +86,7 @@ required:
   - mdio
   - ethernet-ports
 
-additionalProperties: false
+unevaluatedProperties: false
 
 examples:

To be applied on top of this patch. It takes into account the
"required:" for 'ethernet-port' and also reuses the 
$ref: ethernet-switch.yaml#/$defs/ethernet-ports

Last, but not least:
make dt_binding_check DT_SCHEMA_FILES=nxp,imx28-mtip-switch.yaml
make CHECK_DTBS=y DT_SCHEMA_FILES=nxp,imx28-mtip-switch.yaml
nxp/mxs/imx28-xea.dtb

show no errors.


> > +
> > +properties:
> > +  compatible:
> > +    const: nxp,imx28-mtip-switch
> > +
> > +  reg:
> > +    maxItems: 1
> > +
> > +  phy-supply:
> > +    description:
> > +      Regulator that powers Ethernet PHYs.
> > +
> > +  clocks:
> > +    items:
> > +      - description: Register accessing clock
> > +      - description: Bus access clock
> > +      - description: Output clock for external device - e.g. PHY
> > source clock
> > +      - description: IEEE1588 timer clock
> > +
> > +  clock-names:
> > +    items:
> > +      - const: ipg
> > +      - const: ahb
> > +      - const: enet_out
> > +      - const: ptp
> > +
> > +  interrupts:
> > +    items:
> > +      - description: Switch interrupt
> > +      - description: ENET0 interrupt
> > +      - description: ENET1 interrupt
> > +
> > +  pinctrl-names: true
> > +
> > +  mdio:
> > +    type: object
> > +    $ref: mdio.yaml#
> > +    unevaluatedProperties: false
> > +    description:
> > +      Specifies the mdio bus in the switch, used as a container
> > for phy nodes. +
> > +required:
> > +  - compatible
> > +  - reg
> > +  - clocks
> > +  - clock-names
> > +  - interrupts
> > +  - mdio
> > +  - ethernet-ports
> > +
> > +additionalProperties: false  
> 
> unevaluatedProperties: false

Ok.

> 
> > +
> > +examples:
> > +  - |
> > +    #include<dt-bindings/interrupt-controller/irq.h>
> > +    switch@800f0000 {
> > +        compatible = "nxp,imx28-mtip-switch";
> > +        reg = <0x800f0000 0x20000>;
> > +        pinctrl-names = "default";
> > +        pinctrl-0 = <&mac0_pins_a>, <&mac1_pins_a>;
> > +        phy-supply = <&reg_fec_3v3>;
> > +        interrupts = <100>, <101>, <102>;
> > +        clocks = <&clks 57>, <&clks 57>, <&clks 64>, <&clks 35>;
> > +        clock-names = "ipg", "ahb", "enet_out", "ptp";
> > +
> > +        ethernet-ports {
> > +            #address-cells = <1>;
> > +            #size-cells = <0>;
> > +
> > +            mtip_port1: ethernet-port@1 {
> > +                reg = <1>;
> > +                label = "lan0";
> > +                local-mac-address = [ 00 00 00 00 00 00 ];
> > +                phy-mode = "rmii";
> > +                phy-handle = <&ethphy0>;
> > +            };
> > +
> > +            mtip_port2: ethernet-port@2 {
> > +                reg = <2>;
> > +                label = "lan1";
> > +                local-mac-address = [ 00 00 00 00 00 00 ];
> > +                phy-mode = "rmii";
> > +                phy-handle = <&ethphy1>;
> > +            };
> > +        };
> > +
> > +        mdio_sw: mdio {
> > +            #address-cells = <1>;
> > +            #size-cells = <0>;
> > +
> > +            reset-gpios = <&gpio2 13 0>;
> > +            reset-delay-us = <25000>;
> > +            reset-post-delay-us = <10000>;
> > +
> > +            ethphy0: ethernet-phy@0 {
> > +                reg = <0>;
> > +            };
> > +
> > +            ethphy1: ethernet-phy@1 {
> > +                reg = <1>;
> > +            };
> > +        };
> > +    };
> > -- 
> > 2.39.5
> >   


Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH,      Managing Director: Erika Unter
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma@denx.de

Patchew 2.1-devel-b67e4c2

© 2016 - 2026 Red Hat, Inc.