drivers/net/phy/realtek/realtek_main.c | 106 +++++++++++++++++++++++-- 1 file changed, 100 insertions(+), 6 deletions(-)
Like the RTL8211F, the RTL8211E PHY supports up to three LEDs.
Add netdev trigger support for them, too.
Signed-off-by: Michael Klein <michael@fossekall.de>
---
drivers/net/phy/realtek/realtek_main.c | 106 +++++++++++++++++++++++--
1 file changed, 100 insertions(+), 6 deletions(-)
diff --git a/drivers/net/phy/realtek/realtek_main.c b/drivers/net/phy/realtek/realtek_main.c
index abea2291b0f4..ade265cc13f3 100644
--- a/drivers/net/phy/realtek/realtek_main.c
+++ b/drivers/net/phy/realtek/realtek_main.c
@@ -37,6 +37,20 @@
#define RTL8211E_TX_DELAY BIT(12)
#define RTL8211E_RX_DELAY BIT(11)
+#define RTL8211E_LEDCR_EXT_PAGE 0x2c
+
+#define RTL8211E_LEDCR1 0x1a
+#define RTL8211E_LEDCR1_ACT_TXRX BIT(4)
+#define RTL8211E_LEDCR1_MASK BIT(4)
+#define RTL8211E_LEDCR1_SHIFT 1
+
+#define RTL8211E_LEDCR2 0x1c
+#define RTL8211E_LEDCR2_LINK_1000 BIT(2)
+#define RTL8211E_LEDCR2_LINK_100 BIT(1)
+#define RTL8211E_LEDCR2_LINK_10 BIT(0)
+#define RTL8211E_LEDCR2_MASK GENMASK(2, 0)
+#define RTL8211E_LEDCR2_SHIFT 4
+
#define RTL8211F_PHYCR1 0x18
#define RTL8211F_PHYCR2 0x19
#define RTL8211F_INSR 0x1d
@@ -113,7 +127,8 @@
#define RTL_8221B_VN_CG 0x001cc84a
#define RTL_8251B 0x001cc862
-#define RTL8211F_LED_COUNT 3
+/* RTL8211E and RTL8211F support up to three LEDs */
+#define RTL8211x_LED_COUNT 3
MODULE_DESCRIPTION("Realtek PHY driver");
MODULE_AUTHOR("Johnson Leung");
@@ -534,7 +549,7 @@ static int rtl821x_resume(struct phy_device *phydev)
return 0;
}
-static int rtl8211f_led_hw_is_supported(struct phy_device *phydev, u8 index,
+static int rtl8211x_led_hw_is_supported(struct phy_device *phydev, u8 index,
unsigned long rules)
{
const unsigned long mask = BIT(TRIGGER_NETDEV_LINK_10) |
@@ -553,9 +568,11 @@ static int rtl8211f_led_hw_is_supported(struct phy_device *phydev, u8 index,
* rates and Active indication always at all three 10+100+1000
* link rates.
* This code currently uses mode B only.
+ *
+ * RTL8211E PHY LED has one mode, which works like RTL8211F mode B.
*/
- if (index >= RTL8211F_LED_COUNT)
+ if (index >= RTL8211x_LED_COUNT)
return -EINVAL;
/* Filter out any other unsupported triggers. */
@@ -574,7 +591,7 @@ static int rtl8211f_led_hw_control_get(struct phy_device *phydev, u8 index,
{
int val;
- if (index >= RTL8211F_LED_COUNT)
+ if (index >= RTL8211x_LED_COUNT)
return -EINVAL;
val = phy_read_paged(phydev, 0xd04, RTL8211F_LEDCR);
@@ -607,7 +624,7 @@ static int rtl8211f_led_hw_control_set(struct phy_device *phydev, u8 index,
const u16 mask = RTL8211F_LEDCR_MASK << (RTL8211F_LEDCR_SHIFT * index);
u16 reg = 0;
- if (index >= RTL8211F_LED_COUNT)
+ if (index >= RTL8211x_LED_COUNT)
return -EINVAL;
if (test_bit(TRIGGER_NETDEV_LINK_10, &rules))
@@ -630,6 +647,80 @@ static int rtl8211f_led_hw_control_set(struct phy_device *phydev, u8 index,
return phy_modify_paged(phydev, 0xd04, RTL8211F_LEDCR, mask, reg);
}
+static int rtl8211e_led_hw_control_get(struct phy_device *phydev, u8 index,
+ unsigned long *rules)
+{
+ int ret;
+ u16 cr1, cr2;
+
+ if (index >= RTL8211x_LED_COUNT)
+ return -EINVAL;
+
+ ret = rtl8211e_read_ext_page(phydev, RTL8211E_LEDCR_EXT_PAGE, RTL8211E_LEDCR1);
+ if (ret < 0)
+ return ret;
+
+ cr1 = ret >> RTL8211E_LEDCR1_SHIFT * index;
+ if (cr1 & RTL8211E_LEDCR1_ACT_TXRX) {
+ set_bit(TRIGGER_NETDEV_RX, rules);
+ set_bit(TRIGGER_NETDEV_TX, rules);
+ }
+
+ ret = rtl8211e_read_ext_page(phydev, RTL8211E_LEDCR_EXT_PAGE, RTL8211E_LEDCR2);
+ if (ret < 0)
+ return ret;
+
+ cr2 = ret >> RTL8211E_LEDCR2_SHIFT * index;
+ if (cr2 & RTL8211E_LEDCR2_LINK_10)
+ set_bit(TRIGGER_NETDEV_LINK_10, rules);
+
+ if (cr2 & RTL8211E_LEDCR2_LINK_100)
+ set_bit(TRIGGER_NETDEV_LINK_100, rules);
+
+ if (cr2 & RTL8211E_LEDCR2_LINK_1000)
+ set_bit(TRIGGER_NETDEV_LINK_1000, rules);
+
+ return ret;
+}
+
+static int rtl8211e_led_hw_control_set(struct phy_device *phydev, u8 index,
+ unsigned long rules)
+{
+ const u16 cr1mask = RTL8211E_LEDCR1_MASK << (RTL8211E_LEDCR1_SHIFT * index);
+ const u16 cr2mask = RTL8211E_LEDCR2_MASK << (RTL8211E_LEDCR2_SHIFT * index);
+ u16 cr1 = 0, cr2 = 0;
+ int ret;
+
+ if (index >= RTL8211x_LED_COUNT)
+ return -EINVAL;
+
+ if (test_bit(TRIGGER_NETDEV_RX, &rules) ||
+ test_bit(TRIGGER_NETDEV_TX, &rules)) {
+ cr1 |= RTL8211E_LEDCR1_ACT_TXRX;
+ }
+
+ cr1 <<= RTL8211E_LEDCR1_SHIFT * index;
+ ret = rtl8211e_modify_ext_page(phydev, RTL8211E_LEDCR_EXT_PAGE,
+ RTL8211E_LEDCR1, cr1mask, cr1);
+ if (ret < 0)
+ return ret;
+
+ if (test_bit(TRIGGER_NETDEV_LINK_10, &rules))
+ cr2 |= RTL8211E_LEDCR2_LINK_10;
+
+ if (test_bit(TRIGGER_NETDEV_LINK_100, &rules))
+ cr2 |= RTL8211E_LEDCR2_LINK_100;
+
+ if (test_bit(TRIGGER_NETDEV_LINK_1000, &rules))
+ cr2 |= RTL8211E_LEDCR2_LINK_1000;
+
+ cr2 <<= RTL8211E_LEDCR2_SHIFT * index;
+ ret = rtl8211e_modify_ext_page(phydev, RTL8211E_LEDCR_EXT_PAGE,
+ RTL8211E_LEDCR2, cr2mask, cr2);
+
+ return ret;
+}
+
static int rtl8211e_config_init(struct phy_device *phydev)
{
const u16 delay_mask = RTL8211E_CTRL_DELAY |
@@ -1405,6 +1496,9 @@ static struct phy_driver realtek_drvs[] = {
.resume = genphy_resume,
.read_page = rtl821x_read_page,
.write_page = rtl821x_write_page,
+ .led_hw_is_supported = rtl8211x_led_hw_is_supported,
+ .led_hw_control_get = rtl8211e_led_hw_control_get,
+ .led_hw_control_set = rtl8211e_led_hw_control_set,
}, {
PHY_ID_MATCH_EXACT(0x001cc916),
.name = "RTL8211F Gigabit Ethernet",
@@ -1418,7 +1512,7 @@ static struct phy_driver realtek_drvs[] = {
.read_page = rtl821x_read_page,
.write_page = rtl821x_write_page,
.flags = PHY_ALWAYS_CALL_SUSPEND,
- .led_hw_is_supported = rtl8211f_led_hw_is_supported,
+ .led_hw_is_supported = rtl8211x_led_hw_is_supported,
.led_hw_control_get = rtl8211f_led_hw_control_get,
.led_hw_control_set = rtl8211f_led_hw_control_set,
}, {
--
2.39.5© 2016 - 2026 Red Hat, Inc.