On QCM2290-based devices the SE3 is used for the Bluetooth chips. Add
corresponding device node.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/qcm2290.dtsi | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcm2290.dtsi b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
index f0746123e594d5ce5cc314c956eaca11556a9211..5f92eb16482a0ea5f8436cfa7e55849f171ebd24 100644
--- a/arch/arm64/boot/dts/qcom/qcm2290.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
@@ -1239,6 +1239,21 @@ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
 				status = "disabled";
 			};
 
+			uart3: serial@4a8c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x04a8c000 0x0 0x4000>;
+				interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				clock-names = "se";
+				interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+						 &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+						<&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
+						 &config_noc MASTER_APPSS_PROC RPM_ALWAYS_TAG>;
+				interconnect-names = "qup-core",
+						     "qup-config";
+				status = "disabled";
+			};
+
 			i2c4: i2c@4a90000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0x0 0x04a90000 0x0 0x4000>;

-- 
2.39.5

On 1.02.2025 10:18 AM, Dmitry Baryshkov wrote:
> On QCM2290-based devices the SE3 is used for the Bluetooth chips. Add
> corresponding device node.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/qcm2290.dtsi | 15 +++++++++++++++
>  1 file changed, 15 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/qcm2290.dtsi b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
> index f0746123e594d5ce5cc314c956eaca11556a9211..5f92eb16482a0ea5f8436cfa7e55849f171ebd24 100644
> --- a/arch/arm64/boot/dts/qcom/qcm2290.dtsi
> +++ b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
> @@ -1239,6 +1239,21 @@ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
>  				status = "disabled";
>  			};
>  
> +			uart3: serial@4a8c000 {
> +				compatible = "qcom,geni-uart";
> +				reg = <0x0 0x04a8c000 0x0 0x4000>;
> +				interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
> +				clock-names = "se";
> +				interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
> +						 &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
> +						<&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
> +						 &config_noc MASTER_APPSS_PROC RPM_ALWAYS_TAG>;

This path doesn't look quite right.. there'MASTER_APPSS_PROC is only
on one of these.

+ RPM_ACTIVE_TAG

Konrad

On Sat, Feb 01, 2025 at 04:19:01PM +0100, Konrad Dybcio wrote:
> On 1.02.2025 10:18 AM, Dmitry Baryshkov wrote:
> > On QCM2290-based devices the SE3 is used for the Bluetooth chips. Add
> > corresponding device node.
> > 
> > Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> > ---
> >  arch/arm64/boot/dts/qcom/qcm2290.dtsi | 15 +++++++++++++++
> >  1 file changed, 15 insertions(+)
> > 
> > diff --git a/arch/arm64/boot/dts/qcom/qcm2290.dtsi b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
> > index f0746123e594d5ce5cc314c956eaca11556a9211..5f92eb16482a0ea5f8436cfa7e55849f171ebd24 100644
> > --- a/arch/arm64/boot/dts/qcom/qcm2290.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
> > @@ -1239,6 +1239,21 @@ &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
> >  				status = "disabled";
> >  			};
> >  
> > +			uart3: serial@4a8c000 {
> > +				compatible = "qcom,geni-uart";
> > +				reg = <0x0 0x04a8c000 0x0 0x4000>;
> > +				interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>;
> > +				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
> > +				clock-names = "se";
> > +				interconnects = <&qup_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
> > +						 &qup_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
> > +						<&bimc MASTER_APPSS_PROC RPM_ALWAYS_TAG
> > +						 &config_noc MASTER_APPSS_PROC RPM_ALWAYS_TAG>;
> 
> This path doesn't look quite right.. there'MASTER_APPSS_PROC is only
> on one of these.

Hmm. I should check my c&p source then.

> 
> + RPM_ACTIVE_TAG
> 
> Konrad

-- 
With best wishes
Dmitry