wcd937x codec contains soundwire RX and TX slave devices
and can convert digital audio to analog audio and vice versa.
The codec node also requires description of reset pin/gpio.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
---
arch/arm64/boot/dts/qcom/qrb4210-rb2.dts | 47 ++++++++++++++++++++++++
1 file changed, 47 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts b/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts
index edfb18c85da8..6217bc6e6282 100644
--- a/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts
+++ b/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts
@@ -5,6 +5,7 @@
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/sound/qcom,q6afe.h>
#include <dt-bindings/sound/qcom,q6asm.h>
@@ -146,6 +147,25 @@ codec {
};
};
+ wcd937x: codec {
+ compatible = "qcom,wcd9370-codec";
+ pinctrl-0 = <&wcd_reset_n>;
+ pinctrl-names = "default";
+ reset-gpios = <&tlmm 82 GPIO_ACTIVE_LOW>;
+ vdd-buck-supply = <&vreg_l9a_1p8>;
+ vdd-rxtx-supply = <&vreg_l9a_1p8>;
+ vdd-px-supply = <&vreg_l9a_1p8>;
+ vdd-mic-bias-supply = <&vdc_vbat_som>;
+ qcom,micbias1-microvolt = <1800000>;
+ qcom,micbias2-microvolt = <1800000>;
+ qcom,micbias3-microvolt = <1800000>;
+ qcom,micbias4-microvolt = <1800000>;
+ qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+ qcom,rx-device = <&wcd937x_rx>;
+ qcom,tx-device = <&wcd937x_tx>;
+ #sound-dai-cells = <1>;
+ };
+
vreg_hdmi_out_1p2: regulator-hdmi-out-1p2 {
compatible = "regulator-fixed";
regulator-name = "VREG_HDMI_OUT_1P2";
@@ -599,6 +619,26 @@ &sleep_clk {
clock-frequency = <32000>;
};
+&swr1 {
+ status = "okay";
+
+ wcd937x_rx: codec@0,4 {
+ compatible = "sdw20217010a00";
+ reg = <0 4>;
+ qcom,rx-port-mapping = <1 2 3 4 5>;
+ };
+};
+
+&swr0 {
+ status = "okay";
+
+ wcd937x_tx: codec@0,3 {
+ compatible = "sdw20217010a00";
+ reg = <0 3>;
+ qcom,tx-port-mapping = <1 1 2 3>;
+ };
+};
+
&tlmm {
gpio-reserved-ranges = <43 2>, <49 1>, <54 1>,
<56 3>, <61 2>, <64 1>,
@@ -683,6 +723,13 @@ sdc2_card_det_n: sd-card-det-n-state {
drive-strength = <2>;
bias-pull-up;
};
+
+ wcd_reset_n: wcd-reset-n-state {
+ pins = "gpio82";
+ function = "gpio";
+ drive-strength = <16>;
+ output-high;
+ };
};
&uart3 {
--
2.45.2