This series aims to enable display on the QCS615 platform

1.Add MDSS & DPU support for QCS615
2.Add DSI support for QCS615

QCS615 platform supports DisplayPort, and this feature will be added in a future patch

Only dts part of this patch series depends on the following patch series
The other dependency patches have already been merged into linux-next
- dispcc
https://lore.kernel.org/all/20241108-qcs615-mm-clockcontroller-v3-0-7d3b2d235fdf@quicinc.com/
- dispcc dts
https://lore.kernel.org/lkml/20241108-qcs615-mm-dt-nodes-v1-0-b2669cac0624@quicinc.com/

Signed-off-by: Li Liu <quic_lliu6@quicinc.com>
Signed-off-by: Fange Zhang <quic_fangez@quicinc.com>
---
Changes in v4:
- Add dp-connector node for anx_7625_out [Dmitry]
- Add missing qcom,sm6150-dsi-ctrl for dsi-controller-main.yaml [Krzysztof]
- Change VIG_SDM845_MASK to VIG_SDM845_MASK_SDMA for sm6150_sspp [Abhinav]
- Change DMA_SDM845_MASK to DMA_SDM845_MASK_SDMA for sm6150_sspp [Abhinav]
- Remove redundant annotation from sdm845_dsi_cfg [Dmitry]
- Remove redundant blocks from sm6150_intf [Dmitry]
- Update mdp_opp_table opp clk to correct value
- Link to v3: https://lore.kernel.org/r/20241122-add-display-support-for-qcs615-platform-v3-0-35252e3a51fe@quicinc.com

Changes in v3:
- Add reg_bus_bw for sm6150_data [Dmitry]
- Remove patch for SX150X defconfig [Dmitry]
- Remove dsi0_hpd_cfg_pins from ioexp [Dmitry]
- Remove dsi0_cdet_cfg_pins from ioexpa [Dmitry]
- Remove tlmm node for ioexp_intr_active and ioAexp_reset_active [Dmitry]
- Remove qcs615_dsi_regulators and reuse sdm845_dsi_cfg [Dmitry, Konrad]
- Rename qcs615/QCS615 to sm6150/SM6150 for whole patch [Dmitry]
- Rename qcom,dsi-phy-14nm-615 to qcom,sm6150-dsi-phy-14nm [Dmitry]
- Rename qcom,qcs615-dsi-ctrl to qcom,sm6150-dsi-ctrl [Dmitry]
- Rename qcom,qcs615-dpu to qcom,sm6150-dpu [Dmitry]
- Rename qcom,qcs615-mdss to qcom,sm6150-mdss [Dmitry]
- Split drm dsi patch to dsi and dsi phy [Dmitry]
- Update yaml clocks node with ephemeral nodes and remove unsed include [Dmitry, Rob]
- Link to v2: https://lore.kernel.org/r/20241113-add-display-support-for-qcs615-platform-v2-0-2873eb6fb869@quicinc.com

Changes in v2:
- Add QCS615 DP controller comment in commit message [Dmitry]
- Add comments for dsi_dp_hpd_cfg_pins and dsi_dp_cdet_cfg_pins [Dmitry]
- Add missing port@1 for connector for anx7625 [Dmitry]
- Change 0 to QCOM_ICC_TAG_ALWAYS for mdss interconnects [Dmitry]
- Change 0 to GPIO_ACTIVE_HIGH for GPIO flags [Dmitry]
- Move anx_7625 to same node [Dmitry]
- Move status to last in mdss_dsi0 [Dmitry]
- Rename dsi0_hpd_cfg_pins to dsi_dp_hpd_cfg_pins in ioexp [Dmitry]
- Rename dsi0_cdet_cfg_pins to dsi_dp_cdet_cfg_pins in ioexp [Dmitry]
- Rename anx_7625_1 to dsi_anx_7625 in ioexp [Dmitry]
- Remove absent block in qcs615_lm [Dmitry]
- Remove merge_3d value in qcs615_pp [Dmitry]
- Remove redundant annotation in qcs615_sspp [Dmitry]
- Remove unsupported dsi clk from dsi0_opp_table [Dmitry]
- Remove dp_hpd_cfg_pins node from ioexp [Dmitry]
- Splite drm driver patches to mdss, dpu and dsi [Dmitry]
- Link to v1: https://lore.kernel.org/r/20241014-add_display_support_for_qcs615-v1-0-4efa191dbdd4@quicinc.com

---
Li Liu (9):
      dt-bindings: display/msm: Add SM6150 DSI phy
      dt-bindings: display/msm: dsi-controller-main: Document SM6150
      dt-bindings: display/msm: Add SM6150 MDSS & DPU
      drm/msm: mdss: Add SM6150 support
      drm/msm/dpu: Add SM6150 support
      drm/msm/dsi: Add dsi phy support for SM6150
      drm/msm/dsi: Add support for SM6150
      arm64: dts: qcom: Add display support for QCS615
      arm64: dts: qcom: Add display support for QCS615 RIDE board

 .../bindings/display/msm/dsi-controller-main.yaml  |   2 +
 .../bindings/display/msm/dsi-phy-14nm.yaml         |   1 +
 .../bindings/display/msm/qcom,sm6150-dpu.yaml      | 108 +++++++++
 .../bindings/display/msm/qcom,sm6150-mdss.yaml     | 245 ++++++++++++++++++++
 arch/arm64/boot/dts/qcom/qcs615-ride.dts           |  89 ++++++++
 arch/arm64/boot/dts/qcom/qcs615.dtsi               | 181 ++++++++++++++-
 .../gpu/drm/msm/disp/dpu1/catalog/dpu_5_3_sm6150.h | 254 +++++++++++++++++++++
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c     |   1 +
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h     |   1 +
 drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c            |   1 +
 drivers/gpu/drm/msm/dsi/dsi_cfg.c                  |   2 +
 drivers/gpu/drm/msm/dsi/dsi_cfg.h                  |   1 +
 drivers/gpu/drm/msm/dsi/phy/dsi_phy.c              |   2 +
 drivers/gpu/drm/msm/dsi/phy/dsi_phy.h              |   1 +
 drivers/gpu/drm/msm/dsi/phy/dsi_phy_14nm.c         |  21 ++
 drivers/gpu/drm/msm/msm_mdss.c                     |   8 +
 16 files changed, 917 insertions(+), 1 deletion(-)
---
base-commit: 1031240d9d007339c6661dddfbe2efda0b3859e9
change-id: 20241209-add-display-support-for-qcs615-platform-22b8e8848f87

Best regards,
-- 
fangez <quic_fangez@quicinc.com>

On Tue, Dec 10, 2024 at 02:53:51PM +0800, Fange Zhang wrote:
> This series aims to enable display on the QCS615 platform
> 
> 1.Add MDSS & DPU support for QCS615
> 2.Add DSI support for QCS615
> 
> QCS615 platform supports DisplayPort, and this feature will be added in a future patch
> 
> Only dts part of this patch series depends on the following patch series
> The other dependency patches have already been merged into linux-next
> - dispcc
> https://lore.kernel.org/all/20241108-qcs615-mm-clockcontroller-v3-0-7d3b2d235fdf@quicinc.com/
> - dispcc dts
> https://lore.kernel.org/lkml/20241108-qcs615-mm-dt-nodes-v1-0-b2669cac0624@quicinc.com/
> 

I don't understand why you send patches to the list with dependencies on
patches that has received feedback and requests for changes. Now you're
forcing me to go see if perhaps there was a new version of that series
that I have merged.

I can't find a v2 of that series, so your series is spam in my inbox.

> Signed-off-by: Li Liu <quic_lliu6@quicinc.com>
> Signed-off-by: Fange Zhang <quic_fangez@quicinc.com>
> ---
> Changes in v4:
> - Add dp-connector node for anx_7625_out [Dmitry]
> - Add missing qcom,sm6150-dsi-ctrl for dsi-controller-main.yaml [Krzysztof]
> - Change VIG_SDM845_MASK to VIG_SDM845_MASK_SDMA for sm6150_sspp [Abhinav]
> - Change DMA_SDM845_MASK to DMA_SDM845_MASK_SDMA for sm6150_sspp [Abhinav]
> - Remove redundant annotation from sdm845_dsi_cfg [Dmitry]
> - Remove redundant blocks from sm6150_intf [Dmitry]
> - Update mdp_opp_table opp clk to correct value
> - Link to v3: https://lore.kernel.org/r/20241122-add-display-support-for-qcs615-platform-v3-0-35252e3a51fe@quicinc.com
> 
> Changes in v3:
> - Add reg_bus_bw for sm6150_data [Dmitry]
> - Remove patch for SX150X defconfig [Dmitry]
> - Remove dsi0_hpd_cfg_pins from ioexp [Dmitry]
> - Remove dsi0_cdet_cfg_pins from ioexpa [Dmitry]
> - Remove tlmm node for ioexp_intr_active and ioAexp_reset_active [Dmitry]
> - Remove qcs615_dsi_regulators and reuse sdm845_dsi_cfg [Dmitry, Konrad]
> - Rename qcs615/QCS615 to sm6150/SM6150 for whole patch [Dmitry]
> - Rename qcom,dsi-phy-14nm-615 to qcom,sm6150-dsi-phy-14nm [Dmitry]
> - Rename qcom,qcs615-dsi-ctrl to qcom,sm6150-dsi-ctrl [Dmitry]
> - Rename qcom,qcs615-dpu to qcom,sm6150-dpu [Dmitry]
> - Rename qcom,qcs615-mdss to qcom,sm6150-mdss [Dmitry]
> - Split drm dsi patch to dsi and dsi phy [Dmitry]
> - Update yaml clocks node with ephemeral nodes and remove unsed include [Dmitry, Rob]
> - Link to v2: https://lore.kernel.org/r/20241113-add-display-support-for-qcs615-platform-v2-0-2873eb6fb869@quicinc.com
> 
> Changes in v2:
> - Add QCS615 DP controller comment in commit message [Dmitry]
> - Add comments for dsi_dp_hpd_cfg_pins and dsi_dp_cdet_cfg_pins [Dmitry]
> - Add missing port@1 for connector for anx7625 [Dmitry]
> - Change 0 to QCOM_ICC_TAG_ALWAYS for mdss interconnects [Dmitry]
> - Change 0 to GPIO_ACTIVE_HIGH for GPIO flags [Dmitry]
> - Move anx_7625 to same node [Dmitry]
> - Move status to last in mdss_dsi0 [Dmitry]
> - Rename dsi0_hpd_cfg_pins to dsi_dp_hpd_cfg_pins in ioexp [Dmitry]
> - Rename dsi0_cdet_cfg_pins to dsi_dp_cdet_cfg_pins in ioexp [Dmitry]
> - Rename anx_7625_1 to dsi_anx_7625 in ioexp [Dmitry]
> - Remove absent block in qcs615_lm [Dmitry]
> - Remove merge_3d value in qcs615_pp [Dmitry]
> - Remove redundant annotation in qcs615_sspp [Dmitry]
> - Remove unsupported dsi clk from dsi0_opp_table [Dmitry]
> - Remove dp_hpd_cfg_pins node from ioexp [Dmitry]
> - Splite drm driver patches to mdss, dpu and dsi [Dmitry]
> - Link to v1: https://lore.kernel.org/r/20241014-add_display_support_for_qcs615-v1-0-4efa191dbdd4@quicinc.com
> 
> ---
> Li Liu (9):
>       dt-bindings: display/msm: Add SM6150 DSI phy
>       dt-bindings: display/msm: dsi-controller-main: Document SM6150
>       dt-bindings: display/msm: Add SM6150 MDSS & DPU
>       drm/msm: mdss: Add SM6150 support
>       drm/msm/dpu: Add SM6150 support
>       drm/msm/dsi: Add dsi phy support for SM6150
>       drm/msm/dsi: Add support for SM6150
>       arm64: dts: qcom: Add display support for QCS615
>       arm64: dts: qcom: Add display support for QCS615 RIDE board

Don't write "..for <soc>", use the same format as all other changes to
such files: "arm64: dts: qcom: <soc>[-board]: change subject"

Regards,
Bjorn
> 
>  .../bindings/display/msm/dsi-controller-main.yaml  |   2 +
>  .../bindings/display/msm/dsi-phy-14nm.yaml         |   1 +
>  .../bindings/display/msm/qcom,sm6150-dpu.yaml      | 108 +++++++++
>  .../bindings/display/msm/qcom,sm6150-mdss.yaml     | 245 ++++++++++++++++++++
>  arch/arm64/boot/dts/qcom/qcs615-ride.dts           |  89 ++++++++
>  arch/arm64/boot/dts/qcom/qcs615.dtsi               | 181 ++++++++++++++-
>  .../gpu/drm/msm/disp/dpu1/catalog/dpu_5_3_sm6150.h | 254 +++++++++++++++++++++
>  drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c     |   1 +
>  drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h     |   1 +
>  drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c            |   1 +
>  drivers/gpu/drm/msm/dsi/dsi_cfg.c                  |   2 +
>  drivers/gpu/drm/msm/dsi/dsi_cfg.h                  |   1 +
>  drivers/gpu/drm/msm/dsi/phy/dsi_phy.c              |   2 +
>  drivers/gpu/drm/msm/dsi/phy/dsi_phy.h              |   1 +
>  drivers/gpu/drm/msm/dsi/phy/dsi_phy_14nm.c         |  21 ++
>  drivers/gpu/drm/msm/msm_mdss.c                     |   8 +
>  16 files changed, 917 insertions(+), 1 deletion(-)
> ---
> base-commit: 1031240d9d007339c6661dddfbe2efda0b3859e9
> change-id: 20241209-add-display-support-for-qcs615-platform-22b8e8848f87
> 
> Best regards,
> -- 
> fangez <quic_fangez@quicinc.com>
>

On Tue, 10 Dec 2024 14:53:51 +0800, Fange Zhang wrote:
> This series aims to enable display on the QCS615 platform
> 
> 1.Add MDSS & DPU support for QCS615
> 2.Add DSI support for QCS615
> 
> QCS615 platform supports DisplayPort, and this feature will be added in a future patch
> 
> [...]

Applied, thanks!

[1/9] dt-bindings: display/msm: Add SM6150 DSI phy
      https://gitlab.freedesktop.org/lumag/msm/-/commit/5902cd2212eb
[2/9] dt-bindings: display/msm: dsi-controller-main: Document SM6150
      https://gitlab.freedesktop.org/lumag/msm/-/commit/e9280f124b3c
[3/9] dt-bindings: display/msm: Add SM6150 MDSS & DPU
      https://gitlab.freedesktop.org/lumag/msm/-/commit/701da2861cbc
[4/9] drm/msm: mdss: Add SM6150 support
      https://gitlab.freedesktop.org/lumag/msm/-/commit/b8871563eb96
[5/9] drm/msm/dpu: Add SM6150 support
      https://gitlab.freedesktop.org/lumag/msm/-/commit/cb2f9144693b
[6/9] drm/msm/dsi: Add dsi phy support for SM6150
      https://gitlab.freedesktop.org/lumag/msm/-/commit/fbf937a89ad2
[7/9] drm/msm/dsi: Add support for SM6150
      https://gitlab.freedesktop.org/lumag/msm/-/commit/8a570c93fb67

Best regards,
-- 
Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

On 2024/12/15 21:10, Dmitry Baryshkov wrote:
> 
> On Tue, 10 Dec 2024 14:53:51 +0800, Fange Zhang wrote:
>> This series aims to enable display on the QCS615 platform
>>
>> 1.Add MDSS & DPU support for QCS615
>> 2.Add DSI support for QCS615
>>
>> QCS615 platform supports DisplayPort, and this feature will be added in a future patch
>>
>> [...]
> 
> Applied, thanks!
ok, got it,thank you!
will only include DTS changes and remove following patches in the next 
update
> 
> [1/9] dt-bindings: display/msm: Add SM6150 DSI phy
>        https://gitlab.freedesktop.org/lumag/msm/-/commit/5902cd2212eb
> [2/9] dt-bindings: display/msm: dsi-controller-main: Document SM6150
>        https://gitlab.freedesktop.org/lumag/msm/-/commit/e9280f124b3c
> [3/9] dt-bindings: display/msm: Add SM6150 MDSS & DPU
>        https://gitlab.freedesktop.org/lumag/msm/-/commit/701da2861cbc
> [4/9] drm/msm: mdss: Add SM6150 support
>        https://gitlab.freedesktop.org/lumag/msm/-/commit/b8871563eb96
> [5/9] drm/msm/dpu: Add SM6150 support
>        https://gitlab.freedesktop.org/lumag/msm/-/commit/cb2f9144693b
> [6/9] drm/msm/dsi: Add dsi phy support for SM6150
>        https://gitlab.freedesktop.org/lumag/msm/-/commit/fbf937a89ad2
> [7/9] drm/msm/dsi: Add support for SM6150
>        https://gitlab.freedesktop.org/lumag/msm/-/commit/8a570c93fb67
> 
> Best regards,