The BMP{2,3,5}80 and BME280 devices have an SPI interface, so include it
in the device-tree.

Signed-off-by: Vasileios Amoiridis <vassilisamir@gmail.com>
---
 .../bindings/iio/pressure/bmp085.yaml         | 35 +++++++++++++++++++
 1 file changed, 35 insertions(+)

diff --git a/Documentation/devicetree/bindings/iio/pressure/bmp085.yaml b/Documentation/devicetree/bindings/iio/pressure/bmp085.yaml
index cb201cecfa1a..cbddc7bb26a6 100644
--- a/Documentation/devicetree/bindings/iio/pressure/bmp085.yaml
+++ b/Documentation/devicetree/bindings/iio/pressure/bmp085.yaml
@@ -55,12 +55,16 @@ properties:
       If not set, defaults to push-pull configuration.
     type: boolean
 
+  spi-max-frequency:
+    maximum: 10000000
+
 required:
   - compatible
   - vddd-supply
   - vdda-supply
 
 allOf:
+  - $ref: /schemas/spi/spi-peripheral-props.yaml#
   - if:
       properties:
         compatible:
@@ -73,6 +77,19 @@ allOf:
     then:
       properties:
         interrupts: false
+  - if:
+      properties:
+        compatible:
+          not:
+            contains:
+              enum:
+                - bosch,bmp280
+                - bosch,bme280
+                - bosch,bmp380
+                - bosch,bmp580
+    then:
+      properties:
+        spi-max-frequency: false
 
 additionalProperties: false
 
@@ -93,3 +110,21 @@ examples:
             vdda-supply = <&bar>;
         };
     };
+  - |
+    # include <dt-bindings/gpio/gpio.h>
+    # include <dt-bindings/interrupt-controller/irq.h>
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        pressure@0 {
+            compatible = "bosch,bmp280";
+            reg = <0>;
+            spi-max-frequency = <10000000>;
+            interrupt-parent = <&gpio0>;
+            interrupts = <25 IRQ_TYPE_EDGE_RISING>;
+            reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+            vddd-supply = <&foo>;
+            vdda-supply = <&bar>;
+        };
+    };
+
-- 
2.43.0

On Fri, Nov 29, 2024 at 12:24:48AM +0100, Vasileios Amoiridis wrote:
> @@ -73,6 +77,19 @@ allOf:
>      then:
>        properties:
>          interrupts: false
> +  - if:
> +      properties:
> +        compatible:
> +          not:
> +            contains:
> +              enum:

You have just two variants in this "not-containts", so invert your
clause. Easier code.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

On Fri, Nov 29, 2024 at 08:22:00AM +0100, Krzysztof Kozlowski wrote:
> On Fri, Nov 29, 2024 at 12:24:48AM +0100, Vasileios Amoiridis wrote:
> > @@ -73,6 +77,19 @@ allOf:
> >      then:
> >        properties:
> >          interrupts: false
> > +  - if:
> > +      properties:
> > +        compatible:
> > +          not:
> > +            contains:
> > +              enum:
> 
> You have just two variants in this "not-containts", so invert your
> clause. Easier code.
> 
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> 
> Best regards,
> Krzysztof
>

Hi Krzysztof,

Thank you very much for the review! I will fix it in the next version.

Cheers,
Vasilis