1. Patchew
  2. linux
  3. View series

[PATCH] drm/bridge: adv7511_audio: Update Audio InfoFrame properly

Stefan Ekenberg posted 1 patch 1 week, 2 days ago
There is a newer version of this series
drivers/gpu/drm/bridge/adv7511/adv7511_audio.c | 14 ++++++++++++--
1 file changed, 12 insertions(+), 2 deletions(-)
[PATCH] drm/bridge: adv7511_audio: Update Audio InfoFrame properly
Posted by Stefan Ekenberg 1 week, 2 days ago 
AUDIO_UPDATE bit (Bit 5 of MAIN register 0x4A) needs to be set to 1
while updating Audio InfoFrame information and then set to 0 when done.
Otherwise partially updated Audio InfoFrames could be sent out. Two
cases where this rule were not followed are fixed:
 - In adv7511_hdmi_hw_params() make sure AUDIO_UPDATE bit is updated
   before/after setting ADV7511_REG_AUDIO_INFOFRAME.
 - In audio_startup() use the correct register for clearing
   AUDIO_UPDATE bit.

The problem with corrupted audio infoframes were discovered by letting
a HDMI logic analyser check the output of ADV7535.

Signed-off-by: Stefan Ekenberg <stefan.ekenberg@axis.com>
---
 drivers/gpu/drm/bridge/adv7511/adv7511_audio.c | 14 ++++++++++++--
 1 file changed, 12 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c b/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c
index 61f4a38e7d2bf6905683cbc9e762b28ecc999d05..8f786592143b6c81e5a434768b51508d5e5f3c73 100644
--- a/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c
+++ b/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c
@@ -153,7 +153,16 @@ static int adv7511_hdmi_hw_params(struct device *dev, void *data,
 			   ADV7511_AUDIO_CFG3_LEN_MASK, len);
 	regmap_update_bits(adv7511->regmap, ADV7511_REG_I2C_FREQ_ID_CFG,
 			   ADV7511_I2C_FREQ_ID_CFG_RATE_MASK, rate << 4);
-	regmap_write(adv7511->regmap, 0x73, 0x1);
+
+	/* send current Audio infoframe values while updating */
+	regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE,
+			   BIT(5), BIT(5));
+
+	regmap_write(adv7511->regmap, ADV7511_REG_AUDIO_INFOFRAME(0), 0x1);
+
+	/* use Audio infoframe updated info */
+	regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE,
+			   BIT(5), 0);
 
 	return 0;
 }
@@ -184,8 +193,9 @@ static int audio_startup(struct device *dev, void *data)
 	regmap_update_bits(adv7511->regmap, ADV7511_REG_GC(0),
 				BIT(7) | BIT(6), BIT(7));
 	/* use Audio infoframe updated info */
-	regmap_update_bits(adv7511->regmap, ADV7511_REG_GC(1),
+	regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE,
 				BIT(5), 0);
+
 	/* enable SPDIF receiver */
 	if (adv7511->audio_source == ADV7511_AUDIO_SOURCE_SPDIF)
 		regmap_update_bits(adv7511->regmap, ADV7511_REG_AUDIO_CONFIG,

---
base-commit: 59b723cd2adbac2a34fc8e12c74ae26ae45bf230
change-id: 20241108-adv7511-audio-info-frame-54614dd4bf57

Best regards,
-- 
Stefan Ekenberg <stefan.ekenberg@axis.com>
Re: [PATCH] drm/bridge: adv7511_audio: Update Audio InfoFrame properly
Posted by Dmitry Baryshkov 1 week ago 
On Wed, Nov 13, 2024 at 08:38:11AM +0100, Stefan Ekenberg wrote:
> AUDIO_UPDATE bit (Bit 5 of MAIN register 0x4A) needs to be set to 1
> while updating Audio InfoFrame information and then set to 0 when done.
> Otherwise partially updated Audio InfoFrames could be sent out. Two
> cases where this rule were not followed are fixed:
>  - In adv7511_hdmi_hw_params() make sure AUDIO_UPDATE bit is updated
>    before/after setting ADV7511_REG_AUDIO_INFOFRAME.
>  - In audio_startup() use the correct register for clearing
>    AUDIO_UPDATE bit.
> 
> The problem with corrupted audio infoframes were discovered by letting
> a HDMI logic analyser check the output of ADV7535.
> 
> Signed-off-by: Stefan Ekenberg <stefan.ekenberg@axis.com>

Missing Fixes tag,

> ---
>  drivers/gpu/drm/bridge/adv7511/adv7511_audio.c | 14 ++++++++++++--
>  1 file changed, 12 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c b/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c
> index 61f4a38e7d2bf6905683cbc9e762b28ecc999d05..8f786592143b6c81e5a434768b51508d5e5f3c73 100644
> --- a/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c
> +++ b/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c
> @@ -153,7 +153,16 @@ static int adv7511_hdmi_hw_params(struct device *dev, void *data,
>  			   ADV7511_AUDIO_CFG3_LEN_MASK, len);
>  	regmap_update_bits(adv7511->regmap, ADV7511_REG_I2C_FREQ_ID_CFG,
>  			   ADV7511_I2C_FREQ_ID_CFG_RATE_MASK, rate << 4);
> -	regmap_write(adv7511->regmap, 0x73, 0x1);
> +
> +	/* send current Audio infoframe values while updating */
> +	regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE,
> +			   BIT(5), BIT(5));
> +
> +	regmap_write(adv7511->regmap, ADV7511_REG_AUDIO_INFOFRAME(0), 0x1);
> +
> +	/* use Audio infoframe updated info */
> +	regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE,
> +			   BIT(5), 0);
>  
>  	return 0;
>  }
> @@ -184,8 +193,9 @@ static int audio_startup(struct device *dev, void *data)
>  	regmap_update_bits(adv7511->regmap, ADV7511_REG_GC(0),
>  				BIT(7) | BIT(6), BIT(7));
>  	/* use Audio infoframe updated info */
> -	regmap_update_bits(adv7511->regmap, ADV7511_REG_GC(1),
> +	regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE,
>  				BIT(5), 0);

Should the REG_GC(1) still be written?

> +
>  	/* enable SPDIF receiver */
>  	if (adv7511->audio_source == ADV7511_AUDIO_SOURCE_SPDIF)
>  		regmap_update_bits(adv7511->regmap, ADV7511_REG_AUDIO_CONFIG,
> 
> ---
> base-commit: 59b723cd2adbac2a34fc8e12c74ae26ae45bf230
> change-id: 20241108-adv7511-audio-info-frame-54614dd4bf57
> 
> Best regards,
> -- 
> Stefan Ekenberg <stefan.ekenberg@axis.com>
> 

-- 
With best wishes
Dmitry
Re: [PATCH] drm/bridge: adv7511_audio: Update Audio InfoFrame properly
Posted by Stefan Ekenberg 1 week ago 
On 11/15/24 09:16, Dmitry Baryshkov wrote:
> On Wed, Nov 13, 2024 at 08:38:11AM +0100, Stefan Ekenberg wrote:
>> AUDIO_UPDATE bit (Bit 5 of MAIN register 0x4A) needs to be set to 1
>> while updating Audio InfoFrame information and then set to 0 when done.
>> Otherwise partially updated Audio InfoFrames could be sent out. Two
>> cases where this rule were not followed are fixed:
>>   - In adv7511_hdmi_hw_params() make sure AUDIO_UPDATE bit is updated
>>     before/after setting ADV7511_REG_AUDIO_INFOFRAME.
>>   - In audio_startup() use the correct register for clearing
>>     AUDIO_UPDATE bit.
>>
>> The problem with corrupted audio infoframes were discovered by letting
>> a HDMI logic analyser check the output of ADV7535.
>>
>> Signed-off-by: Stefan Ekenberg <stefan.ekenberg@axis.com>
> 
> Missing Fixes tag,

Ok, I will add Fixes tag.

> 
>> ---
>>   drivers/gpu/drm/bridge/adv7511/adv7511_audio.c | 14 ++++++++++++--
>>   1 file changed, 12 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c b/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c
>> index 61f4a38e7d2bf6905683cbc9e762b28ecc999d05..8f786592143b6c81e5a434768b51508d5e5f3c73 100644
>> --- a/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c
>> +++ b/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c
>> @@ -153,7 +153,16 @@ static int adv7511_hdmi_hw_params(struct device *dev, void *data,
>>   			   ADV7511_AUDIO_CFG3_LEN_MASK, len);
>>   	regmap_update_bits(adv7511->regmap, ADV7511_REG_I2C_FREQ_ID_CFG,
>>   			   ADV7511_I2C_FREQ_ID_CFG_RATE_MASK, rate << 4);
>> -	regmap_write(adv7511->regmap, 0x73, 0x1);
>> +
>> +	/* send current Audio infoframe values while updating */
>> +	regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE,
>> +			   BIT(5), BIT(5));
>> +
>> +	regmap_write(adv7511->regmap, ADV7511_REG_AUDIO_INFOFRAME(0), 0x1);
>> +
>> +	/* use Audio infoframe updated info */
>> +	regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE,
>> +			   BIT(5), 0);
>>   
>>   	return 0;
>>   }
>> @@ -184,8 +193,9 @@ static int audio_startup(struct device *dev, void *data)
>>   	regmap_update_bits(adv7511->regmap, ADV7511_REG_GC(0),
>>   				BIT(7) | BIT(6), BIT(7));
>>   	/* use Audio infoframe updated info */
>> -	regmap_update_bits(adv7511->regmap, ADV7511_REG_GC(1),
>> +	regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE,
>>   				BIT(5), 0);
> 
> Should the REG_GC(1) still be written?

The comment before this line states "use Audio infoframe updated info" 
and, before my change, bit 5 of REG_GC(1) was cleared by the line I 
removed. Bit 5 is positioned within field GC_PP[3:0] and that field 
doesn't control audio infoframe and is read-only. My conclusion 
therefore was that the author if this code actually meant to clear bit 5 
of REG_INFOFRAME_UPDATE from the very beginning. In short, clearing bit 
5 of REG_GC(1) is invalid since it is a read-only field.

> 
>> +
>>   	/* enable SPDIF receiver */
>>   	if (adv7511->audio_source == ADV7511_AUDIO_SOURCE_SPDIF)
>>   		regmap_update_bits(adv7511->regmap, ADV7511_REG_AUDIO_CONFIG,
>>
>> ---
>> base-commit: 59b723cd2adbac2a34fc8e12c74ae26ae45bf230
>> change-id: 20241108-adv7511-audio-info-frame-54614dd4bf57
>>
>> Best regards,
>> -- 
>> Stefan Ekenberg <stefan.ekenberg@axis.com>
>>
>
Re: [PATCH] drm/bridge: adv7511_audio: Update Audio InfoFrame properly
Posted by Dmitry Baryshkov 1 week ago 
On Fri, 15 Nov 2024 at 14:25, Stefan Ekenberg <stefan.ekenberg@axis.com> wrote:
>
> On 11/15/24 09:16, Dmitry Baryshkov wrote:
> > On Wed, Nov 13, 2024 at 08:38:11AM +0100, Stefan Ekenberg wrote:
> >> AUDIO_UPDATE bit (Bit 5 of MAIN register 0x4A) needs to be set to 1
> >> while updating Audio InfoFrame information and then set to 0 when done.
> >> Otherwise partially updated Audio InfoFrames could be sent out. Two
> >> cases where this rule were not followed are fixed:
> >>   - In adv7511_hdmi_hw_params() make sure AUDIO_UPDATE bit is updated
> >>     before/after setting ADV7511_REG_AUDIO_INFOFRAME.
> >>   - In audio_startup() use the correct register for clearing
> >>     AUDIO_UPDATE bit.
> >>
> >> The problem with corrupted audio infoframes were discovered by letting
> >> a HDMI logic analyser check the output of ADV7535.
> >>
> >> Signed-off-by: Stefan Ekenberg <stefan.ekenberg@axis.com>
> >
> > Missing Fixes tag,
>
> Ok, I will add Fixes tag.
>
> >
> >> ---
> >>   drivers/gpu/drm/bridge/adv7511/adv7511_audio.c | 14 ++++++++++++--
> >>   1 file changed, 12 insertions(+), 2 deletions(-)
> >>
> >> diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c b/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c
> >> index 61f4a38e7d2bf6905683cbc9e762b28ecc999d05..8f786592143b6c81e5a434768b51508d5e5f3c73 100644
> >> --- a/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c
> >> +++ b/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c
> >> @@ -153,7 +153,16 @@ static int adv7511_hdmi_hw_params(struct device *dev, void *data,
> >>                         ADV7511_AUDIO_CFG3_LEN_MASK, len);
> >>      regmap_update_bits(adv7511->regmap, ADV7511_REG_I2C_FREQ_ID_CFG,
> >>                         ADV7511_I2C_FREQ_ID_CFG_RATE_MASK, rate << 4);
> >> -    regmap_write(adv7511->regmap, 0x73, 0x1);
> >> +
> >> +    /* send current Audio infoframe values while updating */
> >> +    regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE,
> >> +                       BIT(5), BIT(5));
> >> +
> >> +    regmap_write(adv7511->regmap, ADV7511_REG_AUDIO_INFOFRAME(0), 0x1);
> >> +
> >> +    /* use Audio infoframe updated info */
> >> +    regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE,
> >> +                       BIT(5), 0);
> >>
> >>      return 0;
> >>   }
> >> @@ -184,8 +193,9 @@ static int audio_startup(struct device *dev, void *data)
> >>      regmap_update_bits(adv7511->regmap, ADV7511_REG_GC(0),
> >>                              BIT(7) | BIT(6), BIT(7));
> >>      /* use Audio infoframe updated info */
> >> -    regmap_update_bits(adv7511->regmap, ADV7511_REG_GC(1),
> >> +    regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE,
> >>                              BIT(5), 0);
> >
> > Should the REG_GC(1) still be written?
>
> The comment before this line states "use Audio infoframe updated info"
> and, before my change, bit 5 of REG_GC(1) was cleared by the line I
> removed. Bit 5 is positioned within field GC_PP[3:0] and that field
> doesn't control audio infoframe and is read-only. My conclusion
> therefore was that the author if this code actually meant to clear bit 5
> of REG_INFOFRAME_UPDATE from the very beginning. In short, clearing bit
> 5 of REG_GC(1) is invalid since it is a read-only field.

Ack, thanks for the explanation. It might be nice if you can include
this into the commit message.

>
> >
> >> +
> >>      /* enable SPDIF receiver */
> >>      if (adv7511->audio_source == ADV7511_AUDIO_SOURCE_SPDIF)
> >>              regmap_update_bits(adv7511->regmap, ADV7511_REG_AUDIO_CONFIG,
> >>
> >> ---
> >> base-commit: 59b723cd2adbac2a34fc8e12c74ae26ae45bf230
> >> change-id: 20241108-adv7511-audio-info-frame-54614dd4bf57
> >>
> >> Best regards,
> >> --
> >> Stefan Ekenberg <stefan.ekenberg@axis.com>
> >>
> >
>


-- 
With best wishes
Dmitry
Re: [PATCH] drm/bridge: adv7511_audio: Update Audio InfoFrame properly
Posted by Stefan Ekenberg 4 days, 21 hours ago 
On 11/15/24 20:49, Dmitry Baryshkov wrote:
> On Fri, 15 Nov 2024 at 14:25, Stefan Ekenberg <stefan.ekenberg@axis.com> wrote:
>>
>> On 11/15/24 09:16, Dmitry Baryshkov wrote:
>>> On Wed, Nov 13, 2024 at 08:38:11AM +0100, Stefan Ekenberg wrote:
>>>> AUDIO_UPDATE bit (Bit 5 of MAIN register 0x4A) needs to be set to 1
>>>> while updating Audio InfoFrame information and then set to 0 when done.
>>>> Otherwise partially updated Audio InfoFrames could be sent out. Two
>>>> cases where this rule were not followed are fixed:
>>>>    - In adv7511_hdmi_hw_params() make sure AUDIO_UPDATE bit is updated
>>>>      before/after setting ADV7511_REG_AUDIO_INFOFRAME.
>>>>    - In audio_startup() use the correct register for clearing
>>>>      AUDIO_UPDATE bit.
>>>>
>>>> The problem with corrupted audio infoframes were discovered by letting
>>>> a HDMI logic analyser check the output of ADV7535.
>>>>
>>>> Signed-off-by: Stefan Ekenberg <stefan.ekenberg@axis.com>
>>>
>>> Missing Fixes tag,
>>
>> Ok, I will add Fixes tag.
>>
>>>
>>>> ---
>>>>    drivers/gpu/drm/bridge/adv7511/adv7511_audio.c | 14 ++++++++++++--
>>>>    1 file changed, 12 insertions(+), 2 deletions(-)
>>>>
>>>> diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c b/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c
>>>> index 61f4a38e7d2bf6905683cbc9e762b28ecc999d05..8f786592143b6c81e5a434768b51508d5e5f3c73 100644
>>>> --- a/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c
>>>> +++ b/drivers/gpu/drm/bridge/adv7511/adv7511_audio.c
>>>> @@ -153,7 +153,16 @@ static int adv7511_hdmi_hw_params(struct device *dev, void *data,
>>>>                          ADV7511_AUDIO_CFG3_LEN_MASK, len);
>>>>       regmap_update_bits(adv7511->regmap, ADV7511_REG_I2C_FREQ_ID_CFG,
>>>>                          ADV7511_I2C_FREQ_ID_CFG_RATE_MASK, rate << 4);
>>>> -    regmap_write(adv7511->regmap, 0x73, 0x1);
>>>> +
>>>> +    /* send current Audio infoframe values while updating */
>>>> +    regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE,
>>>> +                       BIT(5), BIT(5));
>>>> +
>>>> +    regmap_write(adv7511->regmap, ADV7511_REG_AUDIO_INFOFRAME(0), 0x1);
>>>> +
>>>> +    /* use Audio infoframe updated info */
>>>> +    regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE,
>>>> +                       BIT(5), 0);
>>>>
>>>>       return 0;
>>>>    }
>>>> @@ -184,8 +193,9 @@ static int audio_startup(struct device *dev, void *data)
>>>>       regmap_update_bits(adv7511->regmap, ADV7511_REG_GC(0),
>>>>                               BIT(7) | BIT(6), BIT(7));
>>>>       /* use Audio infoframe updated info */
>>>> -    regmap_update_bits(adv7511->regmap, ADV7511_REG_GC(1),
>>>> +    regmap_update_bits(adv7511->regmap, ADV7511_REG_INFOFRAME_UPDATE,
>>>>                               BIT(5), 0);
>>>
>>> Should the REG_GC(1) still be written?
>>
>> The comment before this line states "use Audio infoframe updated info"
>> and, before my change, bit 5 of REG_GC(1) was cleared by the line I
>> removed. Bit 5 is positioned within field GC_PP[3:0] and that field
>> doesn't control audio infoframe and is read-only. My conclusion
>> therefore was that the author if this code actually meant to clear bit 5
>> of REG_INFOFRAME_UPDATE from the very beginning. In short, clearing bit
>> 5 of REG_GC(1) is invalid since it is a read-only field.
> 
> Ack, thanks for the explanation. It might be nice if you can include
> this into the commit message.

No problem, I will extend the commit message with this information.

> 
>>
>>>
>>>> +
>>>>       /* enable SPDIF receiver */
>>>>       if (adv7511->audio_source == ADV7511_AUDIO_SOURCE_SPDIF)
>>>>               regmap_update_bits(adv7511->regmap, ADV7511_REG_AUDIO_CONFIG,
>>>>
>>>> ---
>>>> base-commit: 59b723cd2adbac2a34fc8e12c74ae26ae45bf230
>>>> change-id: 20241108-adv7511-audio-info-frame-54614dd4bf57
>>>>
>>>> Best regards,
>>>> --
>>>> Stefan Ekenberg <stefan.ekenberg@axis.com>
>>>>
>>>
>>
> 
>

Patchew 2.1-devel-b67e4c2

© 2016 - 2024 Red Hat, Inc.