1. Patchew
  2. linux
  3. [PATCH v2 0/6] dts: qcom: Introduce SM8750 device trees
  4. View patch

[PATCH v2 2/6] arm64: dts: qcom: Add pmd8028 and pmih0108 PMICs

Melody Olvera posted 6 patches 1 year, 2 months ago
There is a newer version of this series
[PATCH v2 2/6] arm64: dts: qcom: Add pmd8028 and pmih0108 PMICs
Posted by Melody Olvera 1 year, 2 months ago 
From: Jishnu Prakash <quic_jprakash@quicinc.com>

Add descriptions of pmd8028 and pmih0108 PMICs used on SM8750
platforms.

Signed-off-by: Jishnu Prakash <quic_jprakash@quicinc.com>
Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
---
 arch/arm64/boot/dts/qcom/pmd8028.dtsi  | 56 +++++++++++++++++++++++
 arch/arm64/boot/dts/qcom/pmih0108.dtsi | 62 ++++++++++++++++++++++++++
 2 files changed, 118 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/pmd8028.dtsi
 create mode 100644 arch/arm64/boot/dts/qcom/pmih0108.dtsi

diff --git a/arch/arm64/boot/dts/qcom/pmd8028.dtsi b/arch/arm64/boot/dts/qcom/pmd8028.dtsi
new file mode 100644
index 000000000000..f8ef8e133854
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pmd8028.dtsi
@@ -0,0 +1,56 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pmd8028-thermal {
+			polling-delay-passive = <100>;
+			thermal-sensors = <&pmd8028_temp_alarm>;
+
+			trips {
+				pmd8028_trip0: trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				pmd8028_trip1: trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+	pmd8028: pmic@4 {
+		compatible = "qcom,pmd8028", "qcom,spmi-pmic";
+		reg = <0x4 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmd8028_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmd8028_gpios: gpio@8800 {
+			compatible = "qcom,pmd8028-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmd8028_gpios 0 0 4>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/pmih0108.dtsi b/arch/arm64/boot/dts/qcom/pmih0108.dtsi
new file mode 100644
index 000000000000..3907d8fbcf78
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pmih0108.dtsi
@@ -0,0 +1,62 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pmih0108-thermal {
+			polling-delay-passive = <100>;
+			thermal-sensors = <&pmih0108_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+	pmih0108: pmic@7 {
+		compatible = "qcom,pmih0108", "qcom,spmi-pmic";
+		reg = <0x7 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmih0108_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x7 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmih0108_gpios: gpio@8800 {
+			compatible = "qcom,pmih0108-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmih0108_gpios 0 0 18>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pmih0108_eusb2_repeater: phy@fd00 {
+			compatible = "qcom,pm8550b-eusb2-repeater";
+			reg = <0xfd00>;
+			#phy-cells = <0>;
+		};
+	};
+};
-- 
2.46.1
Re: [PATCH v2 2/6] arm64: dts: qcom: Add pmd8028 and pmih0108 PMICs
Posted by Dmitry Baryshkov 1 year, 2 months ago 
On Mon, Nov 11, 2024 at 04:49:32PM -0800, Melody Olvera wrote:
> From: Jishnu Prakash <quic_jprakash@quicinc.com>
> 
> Add descriptions of pmd8028 and pmih0108 PMICs used on SM8750
> platforms.

Up/lower case?

> 
> Signed-off-by: Jishnu Prakash <quic_jprakash@quicinc.com>
> Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
> ---
>  arch/arm64/boot/dts/qcom/pmd8028.dtsi  | 56 +++++++++++++++++++++++
>  arch/arm64/boot/dts/qcom/pmih0108.dtsi | 62 ++++++++++++++++++++++++++

Those two are independent changes. Please use two separate patches.

>  2 files changed, 118 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/pmd8028.dtsi
>  create mode 100644 arch/arm64/boot/dts/qcom/pmih0108.dtsi
> 
> diff --git a/arch/arm64/boot/dts/qcom/pmd8028.dtsi b/arch/arm64/boot/dts/qcom/pmd8028.dtsi
> new file mode 100644
> index 000000000000..f8ef8e133854
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/pmd8028.dtsi
> @@ -0,0 +1,56 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
> + */
> +
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/spmi/spmi.h>
> +
> +/ {
> +	thermal-zones {
> +		pmd8028-thermal {
> +			polling-delay-passive = <100>;
> +			thermal-sensors = <&pmd8028_temp_alarm>;
> +
> +			trips {
> +				pmd8028_trip0: trip0 {
> +					temperature = <95000>;
> +					hysteresis = <0>;
> +					type = "passive";
> +				};
> +
> +				pmd8028_trip1: trip1 {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "hot";

"critical" ?

> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&spmi_bus {
> +	pmd8028: pmic@4 {
> +		compatible = "qcom,pmd8028", "qcom,spmi-pmic";
> +		reg = <0x4 SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pmd8028_temp_alarm: temp-alarm@a00 {
> +			compatible = "qcom,spmi-temp-alarm";
> +			reg = <0xa00>;
> +			interrupts = <0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> +			#thermal-sensor-cells = <0>;
> +		};
> +
> +		pmd8028_gpios: gpio@8800 {
> +			compatible = "qcom,pmd8028-gpio", "qcom,spmi-gpio";
> +			reg = <0x8800>;
> +			gpio-controller;
> +			gpio-ranges = <&pmd8028_gpios 0 0 4>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/qcom/pmih0108.dtsi b/arch/arm64/boot/dts/qcom/pmih0108.dtsi
> new file mode 100644
> index 000000000000..3907d8fbcf78
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/pmih0108.dtsi
> @@ -0,0 +1,62 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
> + */
> +
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/spmi/spmi.h>
> +
> +/ {
> +	thermal-zones {
> +		pmih0108-thermal {
> +			polling-delay-passive = <100>;
> +			thermal-sensors = <&pmih0108_temp_alarm>;
> +
> +			trips {
> +				trip0 {
> +					temperature = <95000>;
> +					hysteresis = <0>;
> +					type = "passive";
> +				};
> +
> +				trip1 {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "hot";

"critical" ?

> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&spmi_bus {
> +	pmih0108: pmic@7 {
> +		compatible = "qcom,pmih0108", "qcom,spmi-pmic";
> +		reg = <0x7 SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pmih0108_temp_alarm: temp-alarm@a00 {
> +			compatible = "qcom,spmi-temp-alarm";
> +			reg = <0xa00>;
> +			interrupts = <0x7 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> +			#thermal-sensor-cells = <0>;
> +		};
> +
> +		pmih0108_gpios: gpio@8800 {
> +			compatible = "qcom,pmih0108-gpio", "qcom,spmi-gpio";
> +			reg = <0x8800>;
> +			gpio-controller;
> +			gpio-ranges = <&pmih0108_gpios 0 0 18>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		pmih0108_eusb2_repeater: phy@fd00 {
> +			compatible = "qcom,pm8550b-eusb2-repeater";
> +			reg = <0xfd00>;
> +			#phy-cells = <0>;
> +		};
> +	};
> +};
> -- 
> 2.46.1
> 

-- 
With best wishes
Dmitry
Re: [PATCH v2 2/6] arm64: dts: qcom: Add pmd8028 and pmih0108 PMICs
Posted by Melody Olvera 1 year, 2 months ago 

On 11/15/2024 6:58 AM, Dmitry Baryshkov wrote:
> On Mon, Nov 11, 2024 at 04:49:32PM -0800, Melody Olvera wrote:
>> From: Jishnu Prakash <quic_jprakash@quicinc.com>
>>
>> Add descriptions of pmd8028 and pmih0108 PMICs used on SM8750
>> platforms.
> Up/lower case?

Up; will change.

>
>> Signed-off-by: Jishnu Prakash <quic_jprakash@quicinc.com>
>> Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
>> ---
>>   arch/arm64/boot/dts/qcom/pmd8028.dtsi  | 56 +++++++++++++++++++++++
>>   arch/arm64/boot/dts/qcom/pmih0108.dtsi | 62 ++++++++++++++++++++++++++
> Those two are independent changes. Please use two separate patches.

Sure thing. Will split.

>
>>   2 files changed, 118 insertions(+)
>>   create mode 100644 arch/arm64/boot/dts/qcom/pmd8028.dtsi
>>   create mode 100644 arch/arm64/boot/dts/qcom/pmih0108.dtsi
>>
>> diff --git a/arch/arm64/boot/dts/qcom/pmd8028.dtsi b/arch/arm64/boot/dts/qcom/pmd8028.dtsi
>> new file mode 100644
>> index 000000000000..f8ef8e133854
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/pmd8028.dtsi
>> @@ -0,0 +1,56 @@
>> +// SPDX-License-Identifier: BSD-3-Clause
>> +/*
>> + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
>> + */
>> +
>> +#include <dt-bindings/interrupt-controller/irq.h>
>> +#include <dt-bindings/spmi/spmi.h>
>> +
>> +/ {
>> +	thermal-zones {
>> +		pmd8028-thermal {
>> +			polling-delay-passive = <100>;
>> +			thermal-sensors = <&pmd8028_temp_alarm>;
>> +
>> +			trips {
>> +				pmd8028_trip0: trip0 {
>> +					temperature = <95000>;
>> +					hysteresis = <0>;
>> +					type = "passive";
>> +				};
>> +
>> +				pmd8028_trip1: trip1 {
>> +					temperature = <115000>;
>> +					hysteresis = <0>;
>> +					type = "hot";
> "critical" ?

Will add.

>
>> +				};
>> +			};
>> +		};
>> +	};
>> +};
>> +
>> +&spmi_bus {
>> +	pmd8028: pmic@4 {
>> +		compatible = "qcom,pmd8028", "qcom,spmi-pmic";
>> +		reg = <0x4 SPMI_USID>;
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		pmd8028_temp_alarm: temp-alarm@a00 {
>> +			compatible = "qcom,spmi-temp-alarm";
>> +			reg = <0xa00>;
>> +			interrupts = <0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
>> +			#thermal-sensor-cells = <0>;
>> +		};
>> +
>> +		pmd8028_gpios: gpio@8800 {
>> +			compatible = "qcom,pmd8028-gpio", "qcom,spmi-gpio";
>> +			reg = <0x8800>;
>> +			gpio-controller;
>> +			gpio-ranges = <&pmd8028_gpios 0 0 4>;
>> +			#gpio-cells = <2>;
>> +			interrupt-controller;
>> +			#interrupt-cells = <2>;
>> +		};
>> +	};
>> +};
>> diff --git a/arch/arm64/boot/dts/qcom/pmih0108.dtsi b/arch/arm64/boot/dts/qcom/pmih0108.dtsi
>> new file mode 100644
>> index 000000000000..3907d8fbcf78
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/pmih0108.dtsi
>> @@ -0,0 +1,62 @@
>> +// SPDX-License-Identifier: BSD-3-Clause
>> +/*
>> + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
>> + */
>> +
>> +#include <dt-bindings/interrupt-controller/irq.h>
>> +#include <dt-bindings/spmi/spmi.h>
>> +
>> +/ {
>> +	thermal-zones {
>> +		pmih0108-thermal {
>> +			polling-delay-passive = <100>;
>> +			thermal-sensors = <&pmih0108_temp_alarm>;
>> +
>> +			trips {
>> +				trip0 {
>> +					temperature = <95000>;
>> +					hysteresis = <0>;
>> +					type = "passive";
>> +				};
>> +
>> +				trip1 {
>> +					temperature = <115000>;
>> +					hysteresis = <0>;
>> +					type = "hot";
> "critical" ?

Will add.

Thanks,
Melody

>
>> +				};
>> +			};
>> +		};
>> +	};
>> +};
>> +[...]

Patchew 2.1-devel-b67e4c2

© 2016 - 2026 Red Hat, Inc.