The X Elite QCP board has 3 USB-A ports. The ones labed as USB3 and
USB4/6 are both connected to the multiport controller, each one via a
separate NXP PTN3222 eUSB2-to-USB2 redriver to the eUSB2 PHY for
High-Speed support, with a dedicated QMP PHY for SuperSpeed support.

Describe these two redrivers and enable each pair of PHYs along with the
USB controller, all in order to enable support for these 2 USB-A ports.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/x1e80100-qcp.dts | 86 +++++++++++++++++++++++++++++++
 1 file changed, 86 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
index 5ef030c60abe2998d093ee60a6754a90cd5aaf72..f52ead28eb7d16847f5049185ea5ff0d8edb10e7 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
+++ b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
@@ -616,6 +616,40 @@ zap-shader {
 	};
 };
 
+&i2c5 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	eusb3_repeater: redriver@47 {
+		compatible = "nxp,ptn3222";
+		reg = <0x47>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+
+		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb3_reset_n>;
+		pinctrl-names = "default";
+	};
+
+	eusb6_repeater: redriver@4f {
+		compatible = "nxp,ptn3222";
+		reg = <0x4f>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+
+		reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb6_reset_n>;
+		pinctrl-names = "default";
+	};
+};
+
 &lpass_tlmm {
 	spkr_01_sd_n_active: spkr-01-sd-n-active-state {
 		pins = "gpio12";
@@ -819,6 +853,22 @@ edp_reg_en: edp-reg-en-state {
 		bias-disable;
 	};
 
+	eusb3_reset_n: eusb3-reset-n-state {
+		pins = "gpio6";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	eusb6_reset_n: eusb6-reset-n-state {
+		pins = "gpio184";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
 	nvme_reg_en: nvme-reg-en-state {
 		pins = "gpio18";
 		function = "gpio";
@@ -981,3 +1031,39 @@ &usb_1_ss2_dwc3_hs {
 &usb_1_ss2_qmpphy_out {
 	remote-endpoint = <&pmic_glink_ss2_ss_in>;
 };
+
+&usb_mp {
+	status = "okay";
+};
+
+&usb_mp_hsphy0 {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb6_repeater>;
+
+	status = "okay";
+};
+
+&usb_mp_qmpphy0 {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3c_0p8>;
+
+	status = "okay";
+};
+
+&usb_mp_hsphy1 {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb3_repeater>;
+
+	status = "okay";
+};
+
+&usb_mp_qmpphy1 {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3c_0p8>;
+
+	status = "okay";
+};

-- 
2.34.1