Add the missing HID supplies to avoid relying on other consumers to keep
them on.

This also avoids the following warnings on boot:

	i2c_hid_of 0-0010: supply vdd not found, using dummy regulator
	i2c_hid_of 0-0010: supply vddl not found, using dummy regulator
	i2c_hid_of 1-0015: supply vdd not found, using dummy regulator
	i2c_hid_of 1-0015: supply vddl not found, using dummy regulator
	i2c_hid_of 1-003a: supply vdd not found, using dummy regulator
	i2c_hid_of 1-003a: supply vddl not found, using dummy regulator

Note that VREG_MISC_3P3 is also used for things like the fingerprint
reader which are not yet fully described so mark the regulator as always
on for now.

Fixes: d7e03cce0400 ("arm64: dts: qcom: x1e80100-crd: Enable more support")
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
---

Changes in v3
 - move 'pinctrl-names' after 'pinctrl-0'

Changes in v2:
 - amend the pin config in order not to rely on the boot firmware


 arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 40 +++++++++++++++++++++++
 1 file changed, 40 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
index b50accb220e5..88f6b1fa7c74 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
+++ b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
@@ -8,6 +8,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/gpio-keys.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 
 #include "x1e80100.dtsi"
@@ -277,6 +278,23 @@ vreg_edp_3p3: regulator-edp-3p3 {
 		regulator-boot-on;
 	};
 
+	vreg_misc_3p3: regulator-misc-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_MISC_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pm8550ve_8_gpios 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&misc_3p3_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
 	vreg_nvme: regulator-nvme {
 		compatible = "regulator-fixed";
 
@@ -691,6 +709,9 @@ touchpad@15 {
 		hid-descr-addr = <0x1>;
 		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
 
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
 		pinctrl-0 = <&tpad_default>;
 		pinctrl-names = "default";
 
@@ -704,6 +725,9 @@ keyboard@3a {
 		hid-descr-addr = <0x1>;
 		interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
 
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
 		pinctrl-0 = <&kybd_default>;
 		pinctrl-names = "default";
 
@@ -723,6 +747,9 @@ touchscreen@10 {
 		hid-descr-addr = <0x1>;
 		interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;
 
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l15b_1p8>;
+
 		pinctrl-0 = <&ts0_default>;
 		pinctrl-names = "default";
 	};
@@ -856,6 +883,19 @@ &pcie6a_phy {
 	status = "okay";
 };
 
+&pm8550ve_8_gpios {
+	misc_3p3_reg_en: misc-3p3-reg-en-state {
+		pins = "gpio6";
+		function = "normal";
+		bias-disable;
+		drive-push-pull;
+		input-disable;
+		output-enable;
+		power-source = <1>; /* 1.8 V */
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+	};
+};
+
 &pmc8380_3_gpios {
 	edp_bl_en: edp-bl-en-state {
 		pins = "gpio4";
-- 
2.45.2