gpio0 is the same as gpio1 with a different base address.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
---
 arch/arm64/boot/dts/intel/socfpga_agilex5.dtsi | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/arch/arm64/boot/dts/intel/socfpga_agilex5.dtsi b/arch/arm64/boot/dts/intel/socfpga_agilex5.dtsi
index 1162978329c1637aa0fd9a4adef16a9ae5017ac3..57c28e284cccdb99ede6cea2bc0e8dd8aaf47fe9 100644
--- a/arch/arm64/boot/dts/intel/socfpga_agilex5.dtsi
+++ b/arch/arm64/boot/dts/intel/socfpga_agilex5.dtsi
@@ -222,6 +222,26 @@ i3c1: i3c@10da1000 {
 			status = "disabled";
 		};
 
+		gpio0: gpio@10c03200 {
+			compatible = "snps,dw-apb-gpio";
+			reg = <0x10c03200 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			resets = <&rst GPIO0_RESET>;
+			status = "disabled";
+
+			porta: gpio-controller@0 {
+				compatible = "snps,dw-apb-gpio-port";
+				reg = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <24>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
 		gpio1: gpio@10c03300 {
 			compatible = "snps,dw-apb-gpio";
 			reg = <0x10c03300 0x100>;

-- 
2.46.0

On 30/10/2024 13:10, Steffen Trumtrar wrote:
> gpio0 is the same as gpio1 with a different base address.
> 
> Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
> ---
>  arch/arm64/boot/dts/intel/socfpga_agilex5.dtsi | 20 ++++++++++++++++++++
>  1 file changed, 20 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/intel/socfpga_agilex5.dtsi b/arch/arm64/boot/dts/intel/socfpga_agilex5.dtsi
> index 1162978329c1637aa0fd9a4adef16a9ae5017ac3..57c28e284cccdb99ede6cea2bc0e8dd8aaf47fe9 100644
> --- a/arch/arm64/boot/dts/intel/socfpga_agilex5.dtsi
> +++ b/arch/arm64/boot/dts/intel/socfpga_agilex5.dtsi
> @@ -222,6 +222,26 @@ i3c1: i3c@10da1000 {
>  			status = "disabled";
>  		};
>  
> +		gpio0: gpio@10c03200 {
> +			compatible = "snps,dw-apb-gpio";
> +			reg = <0x10c03200 0x100>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			resets = <&rst GPIO0_RESET>;
> +			status = "disabled";

Why is this node disabled? Any external resources missing?

Best regards,
Krzysztof