The RDP433 is a Qualcomm Reference Design Platform based on the
IPQ9574. It has three QCN9274 WiFi devices connected to PCIe1, PCIe2,
and PCIe3. These devices are also connected among themselves via
WSI connection. This WSI connection is essential to exchange control
information among these devices
The WSI connection in RDP433 is represented below:
+-------+ +-------+ +-------+
| pcie2 | | pcie3 | | pcie1 |
| | | | | |
+----->| wsi |------->| wsi |------->| wsi |-----+
| | grp 0 | | grp 0 | | grp 0 | |
| +-------+ +-------+ +-------+ |
+------------------------------------------------------+
Based on the above, the WSI properties for QCN9274 at pcie2 are
(considering QCN9274 at pcie2 is WSI master):
qcom,wsi-group-id = 0
qcom,wsi-master
ports:
tx-port (port@0): endpoint at pcie3 RX port.
rx-port (port@1): endpoint at pcie1 TX port.
Hence, add WiFi nodes with WSI properties for all three QCN9274
devices connected to RDP433.
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
---
arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts | 116 +++++++++++++++++++-
1 file changed, 115 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
index 165ebbb59511..d0ecaefe5b41 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
+++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
@@ -3,7 +3,7 @@
* IPQ9574 RDP433 board device tree source
*
* Copyright (c) 2020-2021 The Linux Foundation. All rights reserved.
- * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2023-2024 Qualcomm Innovation Center, Inc. All rights reserved.
*/
/dts-v1/;
@@ -27,6 +27,44 @@ &pcie1 {
perst-gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
wake-gpios = <&tlmm 27 GPIO_ACTIVE_LOW>;
status = "okay";
+
+ pcie@0 {
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi1@0 {
+ compatible = "pci17cb,1109";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+
+ wsi {
+ qcom,wsi-group-id = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ wifi1_wsi_tx: endpoint {
+ remote-endpoint = <&wifi2_wsi_rx>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ wifi1_wsi_rx: endpoint {
+ remote-endpoint = <&wifi3_wsi_tx>;
+ };
+ };
+ };
+ };
+ };
+ };
};
&pcie2_phy {
@@ -40,6 +78,45 @@ &pcie2 {
perst-gpios = <&tlmm 29 GPIO_ACTIVE_LOW>;
wake-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
status = "okay";
+
+ pcie@0 {
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi2@0 {
+ compatible = "pci17cb,1109";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+
+ wsi {
+ qcom,wsi-group-id = <0>;
+ qcom,wsi-master;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ wifi2_wsi_tx: endpoint {
+ remote-endpoint = <&wifi3_wsi_rx>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ wifi2_wsi_rx: endpoint {
+ remote-endpoint = <&wifi1_wsi_tx>;
+ };
+ };
+ };
+ };
+ };
+ };
};
&pcie3_phy {
@@ -53,6 +130,43 @@ &pcie3 {
perst-gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
wake-gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
status = "okay";
+
+ pcie@0 {
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi3@0 {
+ compatible = "pci17cb,1109";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+
+ wsi {
+ qcom,wsi-group-id = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ wifi3_wsi_tx: endpoint {
+ remote-endpoint = <&wifi1_wsi_rx>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ wifi3_wsi_rx: endpoint {
+ remote-endpoint = <&wifi2_wsi_tx>;
+ };
+ };
+ };
+ };
+ };
+ };
};
&sdhc_1 {
--
2.34.1On 29/10/2024 18:30, Raj Kumar Bhagat wrote:
> The RDP433 is a Qualcomm Reference Design Platform based on the
> IPQ9574. It has three QCN9274 WiFi devices connected to PCIe1, PCIe2,
> and PCIe3. These devices are also connected among themselves via
> WSI connection. This WSI connection is essential to exchange control
> information among these devices
>
> The WSI connection in RDP433 is represented below:
>
> +-------+ +-------+ +-------+
> | pcie2 | | pcie3 | | pcie1 |
> | | | | | |
> +----->| wsi |------->| wsi |------->| wsi |-----+
> | | grp 0 | | grp 0 | | grp 0 | |
> | +-------+ +-------+ +-------+ |
> +------------------------------------------------------+
>
> Based on the above, the WSI properties for QCN9274 at pcie2 are
> (considering QCN9274 at pcie2 is WSI master):
>
> qcom,wsi-group-id = 0
> qcom,wsi-master
> ports:
> tx-port (port@0): endpoint at pcie3 RX port.
> rx-port (port@1): endpoint at pcie1 TX port.
>
> Hence, add WiFi nodes with WSI properties for all three QCN9274
> devices connected to RDP433.
>
> Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
> ---
> arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts | 116 +++++++++++++++++++-
> 1 file changed, 115 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
> index 165ebbb59511..d0ecaefe5b41 100644
> --- a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
> +++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
> @@ -3,7 +3,7 @@
> * IPQ9574 RDP433 board device tree source
> *
> * Copyright (c) 2020-2021 The Linux Foundation. All rights reserved.
> - * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
> + * Copyright (c) 2023-2024 Qualcomm Innovation Center, Inc. All rights reserved.
> */
>
> /dts-v1/;
> @@ -27,6 +27,44 @@ &pcie1 {
> perst-gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
> wake-gpios = <&tlmm 27 GPIO_ACTIVE_LOW>;
> status = "okay";
> +
> + pcie@0 {
> + device_type = "pci";
> + reg = <0x0 0x0 0x0 0x0 0x0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + ranges;
> +
> + wifi1@0 {
Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
Best regards,
Krzysztof
© 2016 - 2024 Red Hat, Inc.